Re: [Debian]: die arme LILO
In der Bootdisk-HOWTO steht was diese Lilo-Meldungen bedeuten; Ein Ausschnitt:
L. LILO boot error codes.
Questions about these errors are asked so often on Usenet that we
include them here as a public service. This summary is excerpted from
Werner Almsberger's LILO User Documentation, available at
<http://sunsite.unc.edu/pub/Linux/system/boot/lilo/lilo-u-20.ps.gz>.
When LILO loads itself, it displays the word ``LILO''. Each letter is
printed before or after performing some specific action. If LILO
fails at some point, the letters printed so far can be used to
identify the problem.
(nothing)
No part of LILO has been loaded. LILO either isn't installed or
the partition on which its boot sector is located isn't active.
L The first stage boot loader has been loaded and started, but it
can't load the second stage boot loader. The two-digit error
codes indicate the type of problem. (See also section ``Disk
error codes''.) This condition usually indicates a media
failure or a geometry mismatch (e.g. bad disk parameters)
LI The first stage boot loader was able to load the second stage
boot loader, but has failed to execute it. This can either be
caused by a geometry mismatch or by moving /boot/boot.b without
running the map installer.
LIL
The second stage boot loader has been started, but it can't load
the descriptor table from the map file. This is typically caused
by a media failure or by a geometry mismatch.
LIL?
The second stage boot loader has been loaded at an incorrect
address. This is typically caused by a subtle geometry mismatch
or by moving /boot/boot.b without running the map installer.
LIL-
The descriptor table is corrupt. This can either be caused by a
geometry mismatch or by moving /boot/map without running the map
installer.
LILO
All parts of LILO have been successfully loaded.
If the BIOS signals an error when LILO is trying to load a boot image,
the respective error code is displayed. These codes range from 0x00
through 0xbb. See the LILO User Guide for an explanation of these.
On Wed, 12 May
1999, Ansgar Hellwig wrote: SC>drwcy@gmx.net schrieb am Wed, May 12, 1999 um
10:33:56AM +0200: SC>>
SC>> hi...
SC>> Ich verbrachte die letzten 2 abende dabei in meinem Misch-system LILO zu
SC>> benützen, jedoch bringen mich how-to/faq und readmes nicht mehr weiter.
SC>> Also ich habe 1 SCSI(sda1(win),sda2(/swap),sda3(/home)) und 1 IDE
SC>> Platte(hda1(/boot)<1024cyl.,hda2(win),hda3(/)). Gebootet wird von scsi. jedoch
SC>> bekomme ich nicht mehr als ein "LI" zu sehen.
SC>>
SC>
SC>
SC>Hallo!
SC>
SC>Versuch mal folgendes in die lilo.conf zu schreiben:
SC>
SC>disk = /dev/sda
SC> bios = 0x80
SC>disk = /dev/hda
SC> bios = 0x81
SC>
SC>
SC>Und wech...
SC>Ansgar Hellwig
SC>
SC>--
SC>******************************************************************
SC>* Ansgar Hellwig WWW: http://hrz.uni-paderborn.de/~f35864/
SC>* Mail: aha@marvin.owl.de
SC>*
SC>------------------------------------------------
SC>Um sich aus der Liste auszutragen schicken Sie
SC>bitte eine E-Mail an majordomo@jfl.de die im Body
SC>"unsubscribe debian-user-de <deine emailadresse>"
SC>enthaelt.
SC>Bei Problemen bitte eine Mail an: Jan.Otto@jfl.de
SC>------------------------------------------------
SC>Anzahl der eingetragenen Mitglieder: 738
--
,---._________________________________
/ \ |~~\_____/~~\__ |
| Christian.Sangohn@post.rwth-aachen.de >---\______====== )-+
| ,---._______________________________/ ~~~|/~~ |
|/ ()
------------------------------------------------
Um sich aus der Liste auszutragen schicken Sie
bitte eine E-Mail an majordomo@jfl.de die im Body
"unsubscribe debian-user-de <deine emailadresse>"
enthaelt.
Bei Problemen bitte eine Mail an: Jan.Otto@jfl.de
------------------------------------------------
Anzahl der eingetragenen Mitglieder: 736
Reply to: