Re: Latest Debian Sparc64 installer
On 12/17/18 04:25, John Paul Adrian Glaubitz wrote:
> Hi Thomas!
>
> On 12/17/18 8:27 AM, Thomas D Dial wrote:
>> I have found debian-10.0-sparc64-NETINST-1.iso (apparent date 5/18/18
>> and debian-9.0-sparc64-NETINST-1.iso (apparent date 4/4/18) at
>> cdimage.debian.org. Is there a later version of either?
>
> I'm working on a newer release, but I need to fix GRUB2 on sparc64 first
> which currently fails to build there due to a change in binutils.
Thanks to everyone who answered. The result of booting from the
installation CD_ROM of 20180516-10:56 is below. I generated the
diagnostic report because of reported CD-ROM failure on a prior attempt:
/pci@8,700000/scsi@6
Target 6
Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011007
{0} ok boot cdrom
Boot device: /pci@8,700000/scsi@6/disk@6,0:f File and args:
Can't open boot device
This was not a problem except with a serial console, and did not recur
after I removed a D-Link DGE-530T gigabit ethernet card that had been
/pci@8,700000: Device 2.
I apologize for the length, but don't know enough about the hardware or
Linux internals to be confident in excluding anything.
====================
@(#)OBP 4.16.4 2004/12/18 05:18
Power-On Reset
Executing Power On SelfTest
0:0>
0:0>@(#) Sun Fire[TM] V280, Sun Blade[TM] 1000 POST 4.16.3 2004/11/05 20:02
/dat/fw/common-source/firmware_re/post/post-build-4.16.3/Camelot/excal/integrated
(firmware_re)
0:0>Copyright � 2004 Sun Microsystems, Inc. All rights reserved
SUN PROPRIETARY/CONFIDENTIAL.
Use is subject to license terms.
0:0>Jump from OBP->POST.
0:0>diag-switch? configuration variable set TRUE.
0:0>Diag level set to MIN.
0:0>MFG scrpt mode set to NONE
0:0>I/O port set to serial TTYA.
0:0>Done with First Init, reset system.
0:0>Current CPU frequency is 400 MHz.
0:0> Resetting to 900
0:0>Clock Synth Reset.
0:0>
0:0>Start selftest...
0:0>CPUs present in system: 0:0 1:0
0:0>Test CPU(s).....
0:0>Init CPU
0:0> UltraSparc_III_base Version 5.11
0:0>DMMU Registers Access
0:0>DMMU TLB DATA RAM Access
0:0>DMMU TLB TAGS Access
0:0>IMMU Registers Access
0:0>IMMU TLB DATA RAM Access
0:0>IMMU TLB TAGS Access
0:0>Probe Ecache
0:0> Size = 00000000.00800000...
0:0>Ecache Data Bitwalk
0:0>Ecache Address Bitwalk
0:0>Scrub and Setup Ecache
0:0>Setup and Enable DMMU
0:0>Setup DMMU Miss Handler
0:0>Test and Init Temp Mailbox
1:0>Init CPU
1:0> UltraSparc_III_base Version 5.11
1:0>DMMU Registers Access
1:0>DMMU TLB DATA RAM Access
1:0>DMMU TLB TAGS Access
1:0>IMMU Registers Access
1:0>IMMU TLB DATA RAM Access
1:0>IMMU TLB TAGS Access
1:0>Probe Ecache
1:0> Size = 00000000.00800000...
1:0>Ecache Data Bitwalk
1:0>Ecache Address Bitwalk
1:0>Scrub and Setup Ecache
1:0>Setup and Enable DMMU
1:0>Setup DMMU Miss Handler
1:0>Test and Init Temp Mailbox
0:0>Init Scan/I2C.....
0:0>Initializing Scan Database
0:0>BBC: 1483203b
0:0>SCSI: 15060045
0:0>ICHIP: 0d1e203b
0:0>RIO: 13e5d03b
0:0>IO-Bridge: 307be06d
0:0>CPMS0: 1142903b
0:0>CPMS1: 1142903b
0:0>CPMS2: 1142903b
0:0>CPMS3: 1142903b
0:0>CPMS4: 1142903b
0:0>CPMS5: 1142903b
0:0>Init I2C
0:0>Unquiesce Safari
0:0>Blast Fans
0:0>Set Trip Temp CPU 0 to 110C
0:0>Set Trip Temp CPU 1 to 110C
0:0>TUES DEC 18 3:44:00 GMT 18
0:0>Safari quick check
0:0> to IO-bridge_0
0:0>Safari full check
0:0> to IO-bridge_0
0:0>Basic Memory Test.....
0:0>Probe and Setup Memory
0:0>INFO: 4096MB Bank 0
0:0>INFO: 4096MB Bank 1
0:0>INFO: 4096MB Bank 2
0:0>INFO: 4096MB Bank 3
0:0>
0:0>Data Bitwalk on Master
0:0> Test Bank 0.
0:0> Test Bank 1.
0:0> Test Bank 2.
0:0> Test Bank 3.
0:0>Address Bitwalk on Master
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 0: 00000000.00000000 to
00000001.00000000.
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 1: 00000001.00000000 to
00000002.00000000.
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 2: 00000002.00000000 to
00000003.00000000.
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 3: 00000003.00000000 to
00000004.00000000.
0:0>Set Mailbox
0:0>Setup Final DMMU Entries
0:0>Post Image Region Scrub
0:0>Run POST from Memory
0:0>Verifying checksum on copied image.
0:0>The Memory's CHECKSUM value is c3b1.
0:0>The Memory's Content Size value is 9b29c.
0:0>Success... Checksum on Memory Validated.
1:0>Safari quick check
1:0> to IO-bridge_0
1:0>Safari full check
1:0> to IO-bridge_0
1:0>Probe and Setup Memory
1:0>INFO: No memory on cpu 1
1:0>Set Mailbox
1:0>Data Bitwalk on mem
1:0> Test Bank 0.
1:0> Test Bank 1.
1:0> Test Bank 2.
1:0> Test Bank 3.
1:0>Setup Final DMMU Entries
1:0>Map Slave POST to master memory
1:0>Print Mem Config
1:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is OFF.
0:0>Memory Block.....
0:0>Print Mem Config
0:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is OFF.
0:0>Memory in non-interleave config:
0:0> Bank 0 4096MB : 00000000.00000000 -> 00000001.00000000.
0:0> Bank 1 4096MB : 00000001.00000000 -> 00000002.00000000.
0:0> Bank 2 4096MB : 00000002.00000000 -> 00000003.00000000.
0:0> Bank 3 4096MB : 00000003.00000000 -> 00000004.00000000.
0:0>Scrub Memory
0:0>Quick Block Mem Test
0:0>Quick Test 16777216 bytes at 00000000.00600000
0:0>40% Done...
1:0>Flush Caches
0:0>Flush Caches
1:0>Get code in ecache.
0:0>Get code in ecache.
0:0>IO-Bridge Tests.....
0:0>IO-Bridge unit 0 init test
0:0>IO-Bridge unit 0 reg test
0:0>IO-Bridge unit 0 mem test
0:0>IO-Bridge unit 0 PCI DMA A test
0:0>IO-Bridge unit 0 PCI DMA B test
0:0>IO-Bridge unit 0 PCI merg test
0:0>IO-Bridge unit 0 PCI iommu test
0:0>IO-Bridge unit 0 PCI stc test
0:0>IO-Bridge unit 0 interrupt test
1:0>IO-Bridge unit 0 init test
1:0>IO-Bridge unit 0 interrupt test
1:0>FPU Registers and Data Path
0:0>FPU Registers and Data Path
1:0>FPU Move Registers
0:0>FPU Move Registers
1:0>FSR Read/Write
0:0>FSR Read/Write
1:0>FPU BLOCK REG TEST
0:0>FPU BLOCK REG TEST
0:0>
0:0>Enable Errors.....
0:0>Turn IO-Bridge 0 errors on
0:0>Turn error traps on
0:0>INFO:
0:0> POST Passed all devices.
0:0>POST: Return to OBP.
1:0>Return to OBP, PASS
0:0>Return to OBP, PASS
@(#)OBP 4.16.4 2004/12/18 05:18
POST Results: Cpu 0
%o0 0000.0000.0000.0000
%o1 0000.0000.0000.0000
%o2 0000.0000.0000.0000
POST Results: Cpu 1
%o0 0000.0000.0000.0000
%o1 0000.0000.0000.0000
%o2 0000.0000.0000.0000
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0010.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB (small-footprint mode) Done
MMUs ON
Find dropin, Copying Done, Size 0000.0000.0000.6290
Jump to RAM Done
Find dropin, Copying Done, Size 0000.0000.0001.24a0
Diagnostic console initializedStart Reason: Initialize Machine
Configuring the machine:
�
@(#)OBP 4.16.4 2004/12/18 05:18
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0004.0000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.6290
Jump to RAM Done
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.1d90
Diagnostic console initializedSystem Reset: (SPOR) (PLL)
Probing system devices
/: gptwo at 0,0 SUNW,UltraSPARC-III (900 MHz @ 6:1, 8 MB) memory-controller
/: gptwo at 1,0 SUNW,UltraSPARC-III (900 MHz @ 6:1, 8 MB) memory-controller
/: gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device
SUNW,fru-device
Loading onboard drivers: ebus
/pci@8,700000/ebus@5: flashprom i2c bbc ppm i2c beep audio rtc gpio pmc
floppy parallel serial
/pci@8,700000/ebus@5/i2c@1,2e: nvram idprom dimm-fru dimm-fru dimm-fru
dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru
/pci@8,700000/ebus@5/i2c@1,30: cpu-fru temperature cpu-fru temperature
fan-control card-reader motherboard-fru i2c-bridge
Memory Configuration:
Segment @ Base: 0 Size: 16384 MB ( 4-Way)
Probing /upa@8,480000 Device 0,0 SUNW,afb
Probing /upa@8,480000 Device 1,0 Nothing there
/pci@8,600000: Device 4 SUNW,qlc fp disk
/pci@8,600000: Device 1 Nothing there
/pci@8,700000: Device 5 network firewire usb
/pci@8,700000: Device 6 scsi disk tape scsi disk tape
/pci@8,700000: Device 1 Nothing there
/pci@8,700000: Device 2 Nothing there
/pci@8,700000: Device 3 Nothing there
/pci@8,700000: Device 4 Nothing there
System Reset: (SPOR) (PLL)
Probing system devices
/: gptwo at 0,0 SUNW,UltraSPARC-III (900 MHz @ 6:1, 8 MB) memory-controller
/: gptwo at 1,0 SUNW,UltraSPARC-III (900 MHz @ 6:1, 8 MB) memory-controller
/: gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device
SUNW,fru-device
Loading onboard drivers: ebus
/pci@8,700000/ebus@5: flashprom i2c bbc ppm i2c beep audio rtc gpio pmc
floppy parallel serial
/pci@8,700000/ebus@5/i2c@1,2e: nvram idprom dimm-fru dimm-fru dimm-fru
dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru
/pci@8,700000/ebus@5/i2c@1,30: cpu-fru temperature cpu-fru temperature
fan-control card-reader motherboard-fru i2c-bridge
Memory Configuration:
Segment @ Base: 0 Size: 16384 MB ( 4-Way)
Probing /upa@8,480000 Device 0,0 SUNW,afb
Probing /upa@8,480000 Device 1,0 Nothing there
/pci@8,600000: Device 4 SUNW,qlc fp disk
/pci@8,600000: Device 1 Nothing there
/pci@8,700000: Device 5 network firewire usb
/pci@8,700000: Device 6 scsi disk tape scsi disk tape
/pci@8,700000: Device 1 Nothing there
/pci@8,700000: Device 2 Nothing there
/pci@8,700000: Device 3 Nothing there
/pci@8,700000: Device 4 Nothing there
SUNW,Sun-Blade-1000 (2 X UltraSPARC-III) , No Keyboard
Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.16.4, 16384 MB memory installed, Serial #53717460.
Ethernet address 0:3:ba:33:a9:d4, Host ID: 8333a9d4.
Initializing 1MB of memory at addr 3fff06000
Initializing
1MB of memory at addr 3fff00000
Initializing 15MB of memory at
addr 3ff000000
Initializing 16368MB of memory at addr
0
{0} ok probe-scsi-all
/pci@8,600000/SUNW,qlc@4
LiD HA LUN --- Port WWN --- ----- Disk description -----
1 1 0 2100002037cda534 SEAGATE ST336704FSUN36G 0726
2 2 0 21000004cf2cb3dd SEAGATE ST373405FSUN72G 0638
/pci@8,700000/scsi@6,1
/pci@8,700000/scsi@6
Target 6
Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011007
{0} ok boot cdrom
Boot device: /pci@8,700000/scsi@6/disk@6,0:f File and args:
SILO Version 1.4.14
\
Welcome to Debian GNU/Linux sid!
This is a Debian installation CDROM, built on 20180516-10:56.
Keep it once you have installed your system, as you can boot from it
to repair the system on your hard disk if that ever becomes necessary.
WARNING: You should completely back up all of your hard disks before
proceeding. The installation procedure can completely and irreversibly
erase them! If you haven't made backups yet, remove the rescue CD from
the drive and press L1-A to get back to the OpenBoot prompt.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted
by applicable law.
[ ENTER - Boot install ] [ Type "expert" - Boot into expert mode ]
[ Type "rescue" - Boot into rescue mode ]
boot:
Allocated 64 Megs of memory at 0x40000000 for kernel
Loaded kernel version 4.16.5
Loading initial ramdisk (14145050 bytes at 0x3FF000000 phys, 0x40C00000
virt)...
-
[ 0.000049] PROMLIB: Sun IEEE Boot Prom 'OBP 4.16.4 2004/12/18 05:18'
[ 0.000081] PROMLIB: Root node compatible:
[ 0.000175] Linux version 4.16.0-1-sparc64
(debian-kernel@lists.debian.org) (gcc version 7.3.0 (Debian 7.3.0-17))
#1 Debian 4.16.5-1 (2018-04-29)
[ 0.282514] bootconsole [earlyprom0] enabled
[ 0.333552] ARCH: SUN4U
[ 0.362760] Ethernet address: 00:03:ba:33:a9:d4
[ 0.416894] MM: PAGE_OFFSET is 0xfff0000000000000 (max_phys_bits == 42)
[ 0.496049] MM: VMALLOC [0x0000000100000000 --> 0x000c000000000000]
[ 0.571045] MM: VMEMMAP [0x000c000000000000 --> 0x0018000000000000]
[ 0.690429] Kernel: Using 3 locked TLB entries for main kernel image.
[ 0.765762] Remapping the kernel...
[ 0.766288] done.
[ 1.140265] OF stdout device is: /pci@8,700000/ebus@5/serial@1,400000:a
[ 1.217602] PROM: Built device tree with 109385 bytes of memory.
[ 1.289537] Top of RAM: 0x3fff08000, Total RAM: 0x3ffed2000
[ 1.356140] Memory hole size: 0MB
[ 1.725408] Allocated 8192 bytes for kernel page tables.
[ 1.787509] Zone ranges:
[ 1.817390] Normal [mem 0x0000000000000000-0x00000003fff07fff]
[ 1.891343] Movable zone start for each node
[ 1.942385] Early memory node ranges
[ 1.985094] node 0: [mem 0x0000000000000000-0x00000003feffdfff]
[ 2.060094] node 0: [mem 0x00000003ff000000-0x00000003ffeb9fff]
[ 2.135093] node 0: [mem 0x00000003ffeca000-0x00000003ffedffff]
[ 2.210092] node 0: [mem 0x00000003fff00000-0x00000003fff01fff]
[ 2.285091] node 0: [mem 0x00000003fff06000-0x00000003fff07fff]
[ 2.360094] Initmem setup node 0 [mem
0x0000000000000000-0x00000003fff07fff]
[ 2.477304] Booting Linux...
[ 2.509884] CPU CAPS: [flush,stbar,swap,muldiv,v9,ultra3,mul32,div32]
[ 2.586962] CPU CAPS: [v8plus,vis,vis2]
[ 2.632800] ------------[ cut here ]------------
[ 2.688036] WARNING: CPU: 0 PID: 0 at
/build/linux-hhlSpw/linux-4.16.5/mm/memblock.c:519
memblock_add_range+0x158/0x300
[ 2.817168] Modules linked in:
[ 2.853634] CPU: 0 PID: 0 Comm: swapper Not tainted 4.16.0-1-sparc64
#1 Debian 4.16.5-1
[ 2.949460] Call Trace:
[ 2.978642] [00000000004664b4] __warn+0xd4/0x100
[ 3.034880] [00000000004665ac] warn_slowpath_null+0x2c/0x40
[ 3.102586] [00000000005b9ed8] memblock_add_range+0x158/0x300
[ 3.172378] [00000000005ba17c] memblock_reserve+0x3c/0x80
[ 3.238010] [0000000000c9a360] __alloc_memory_core_early+0x78/0xac
[ 3.313002] [0000000000c9a778] ___alloc_bootmem_node_nopanic+0x1c/0x58
[ 3.392166] [0000000000c9a8a0] __alloc_bootmem_node+0x6c/0x8c
[ 3.461964] [0000000000c850b8] alloc_irqstack_bootmem+0x18/0x4c
[ 3.533831] [0000000000c85774] setup_arch+0x688/0x6e4
[ 3.595290] [0000000000c82728] start_kernel+0x5c/0x474
[ 3.657788] [0000000000c85090] start_early_boot+0x284/0x294
[ 3.725507] [0000000000a04d80] tlb_fixup_done+0x4c/0x6c
[ 3.789035] [0000000000000000] (null)
[ 3.844253] random: get_random_bytes called from
print_oops_end_marker+0x34/0x60 with crng_init=0
[ 3.950499] ---[ end trace 0000000000000000 ]---
[ 4.005825] kernel BUG at
/build/linux-hhlSpw/linux-4.16.5/mm/memblock.c:447!
[ 4.091122] \|/ ____ \|/
[ 4.091122] "@'/ .. \`@"
[ 4.091122] /_| \__/ |_\
[ 4.091122] \__U_/
[ 4.267156] swapper(0): Kernel bad sw trap 5 [#1]
[ 4.323409] CPU: 0 PID: 0 Comm: swapper Tainted: G W
4.16.0-1-sparc64 #1 Debian 4.16.5-1
[ 4.434865] TSTATE: 0000004480e01607 TPC: 00000000005b9064 TNPC:
00000000005b9068 Y: 0000003a Tainted: G W
[ 4.568200] TPC: <memblock_merge_regions.isra.2+0x84/0x100>
[ 4.634860] g0: 0000000000bbfa30 g1: 0000000000bebdb0 g2:
0000000000bebdb0 g3: 000000000000000e
[ 4.739026] g4: 0000000000bceb88 g5: 0000000000000000 g6:
0000000000bbc000 g7: 0000000000000052
[ 4.843192] o0: 0000000000b1a220 o1: 00000000000001bf o2:
0000000000000000 o3: fff00003ffedc000
[ 4.947357] o4: 0000000000000000 o5: 0000000000000000 sp:
0000000000bbf221 ret_pc: 00000000005b905c
[ 5.055693] RPC: <memblock_merge_regions.isra.2+0x7c/0x100>
[ 5.122357] l0: fff00003ffea5160 l1: 000000000000b160 l2:
fff00003ffe9a000 l3: 0000000000000001
[ 5.226522] l4: 0000000000000005 l5: 0000000000000006 l6:
00000000007fffff l7: 0000000000bd8800
[ 5.330688] i0: 0000000000c147b8 i1: 0000000000c147d0 i2:
000000000000058b i3: 0000000000004000
[ 5.434853] i4: 0000000000000000 i5: 0000000000000000 i6:
0000000000bbf2d1 i7: 00000000005b9eb4
[ 5.539022] I7: <memblock_add_range+0x134/0x300>
[ 5.594225] Call Trace:
[ 5.623396] [00000000005b9eb4] memblock_add_range+0x134/0x300
[ 5.693187] [00000000005ba17c] memblock_reserve+0x3c/0x80
[ 5.758812] [0000000000c9ac0c] memblock_virt_alloc_internal+0xf8/0x19c
[ 5.837977] [0000000000c9af10] memblock_virt_alloc_try_nid+0x58/0xa4
[ 5.915059] [0000000000c8276c] start_kernel+0xa0/0x474
[ 5.977559] [0000000000c85090] start_early_boot+0x284/0x294
[ 6.045267] [0000000000a04d80] tlb_fixup_done+0x4c/0x6c
[ 6.108803] [0000000000000000] (null)
[ 6.164011] Disabling lock debugging due to kernel taint
[ 6.227558] Caller[00000000005b9eb4]: memblock_add_range+0x134/0x300
[ 6.303598] Caller[00000000005ba17c]: memblock_reserve+0x3c/0x80
[ 6.375471] Caller[0000000000c9ac0c]:
memblock_virt_alloc_internal+0xf8/0x19c
[ 6.460887] Caller[0000000000c9af10]:
memblock_virt_alloc_try_nid+0x58/0xa4
[ 6.544219] Caller[0000000000c8276c]: start_kernel+0xa0/0x474
[ 6.612969] Caller[0000000000c85090]: start_early_boot+0x284/0x294
[ 6.686927] Caller[0000000000a04d80]: tlb_fixup_done+0x4c/0x6c
[ 6.756715] Caller[0000000000000000]: (null)
[ 6.818171] Instruction DUMP:
[ 6.818175] 921021bf
[ 6.853588] 7ff9bc41
[ 6.881713] 90122220
[ 6.909838] <91d02005>
[ 6.937961] c2022018
[ 6.966086] 80a08001
[ 6.994211] 324ffff4
[ 7.022336] b8072001
[ 7.050461] c459e010
[ 7.078586]
[ 7.124423] Kernel panic - not syncing: Attempted to kill the idle task!
[ 7.204637] Press Stop-A (L1-A) from sun keyboard or send break
[ 7.204637] twice on console to return to the boot prom
[ 7.337959] ---[ end Kernel panic - not syncing: Attempted to kill
the idle task!
====================
Tom
>
> It's on my TODO list for the holidays.
>
> Adrian
>
Reply to: