Dear team,
I could able to install debian wheezy on sun v890 server with help of firmware files(downloaded from
http://cdimage.debian.org/cdimage/un...i-arch/iso-cd/ uploaded by USB stick).
But after completing the installation ,while booting from disk im getting below error.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
and everything stops there,nothing comes next.I need to hard reset the server for rebooting.
I have tried giving "install video=atyfb:off" on boot: prompt before installing wheezy.but still it is not working.
please see the output below
{2} ok
{2} ok
{2} ok probe-scsi
This command may hang the system if a Stop-A or halt command
has been executed. Please type reset-all to reset the system
before executing this command.
Do you wish to continue? (y/n) n
{2} ok boot disk
Resetting ...
Software Reset
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory.. Done
Initializing OpenBoot
Probing system devices
ChassisSerialNumber 0638AM1097
Probing I/O buses
screen not found.
keyboard not found.
Keyboard not present. Using ttya for input and output.
Probing system devices
ChassisSerialNumber 0638AM1097
Probing I/O buses
Sun Fire V890, No Keyboard
Copyright 2006 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.24, 8192 MB memory installed, Serial #72026096.
Ethernet address 0:14:4f:4b:7:f0, Host ID: 844b07f0.
Rebooting with command: boot disk
Boot device: /pci@8,600000/SUNW,qlc@2/fp@0,0/disk@0,0 File and args:
SILO Version 1.4.14
boot:
Allocated 64 Megs of memory at 0x40000000 for kernel
Uncompressing image...
Loaded kernel version 3.2.57
Loading initial ramdisk (11001924 bytes at 0xA1FF000000 phys, 0x40C00000 virt)...
/
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.22.24 2006/12/08 10:07'
[ 0.000000] PROMLIB: Root node compatible:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-sparc64-smp (
debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.57-3
[ 0.000000] bootconsole [earlyprom0] enabled
[ 0.000000] ARCH: SUN4U
[ 0.000000] Ethernet address: 00:14:4f:4b:07:f0
[ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.000000] Remapping the kernel... done.
[ 0.000000] OF stdout device is: /pci@9,700000/ebus@1/serial@1,400000:a
[ 0.000000] PROM: Built device tree with 117403 bytes of memory.
[ 0.000000] Top of RAM: 0xa1ffb14000, Total RAM: 0x1ffb02000
[ 0.000000] Memory hole size: 655360MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x05000000 -> 0x050ffd8a
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x05000000 -> 0x050ff7ff
[ 0.000000] 0: 0x050ff800 -> 0x050ffd73
[ 0.000000] 0: 0x050ffd7b -> 0x050ffd8a
[ 0.000000] Booting Linux...
[ 0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,ultra3,mul32,div32]
[ 0.000000] CPU CAPS: [v8plus,popc,vis,vis2]
[ 0.000000] PERCPU: Embedded 6 pages/cpu @fffff8a004c00000 s20416 r8192 d20544 u1048576
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1039749
[ 0.000000] Kernel command line: root=/dev/sdb2 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 10, 8388608 bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 9, 4194304 bytes)
[ 0.000000] Memory: 8288000k available (3592k kernel code, 1480k data, 232k init) [fffff80000000000,000000a1ffb14000]
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:255
[ 0.000000] clocksource: mult[64000000] shift[24]
[ 0.000000] clockevent: mult[28f5c29] shift[32]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
I could not able to login into server in anyway as console is also disabled.