[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

SunFire V240 network cards

Hello to all.
I've installed Debian 7 Wheezy on SunFire V240. The server has 4 Gigabit network cards, but when I run ifconfig -a I get the following: 

eth0      Link encap:Ethernet  HWaddr 00:14:4f:8f:ca:5a
          inet addr:172.30.0.161  Bcast:172.30.0.255 Mask:255.255.255.0
          inet6 addr: fe80::214:4fff:fe8f:ca5a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:87718 errors:0 dropped:76 overruns:0 frame:0
          TX packets:490 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6650737 (6.3 MiB)  TX bytes:50656 (49.4 KiB)
          Interrupt:6

eth1      Link encap:Ethernet  HWaddr 00:14:4f:8f:ca:5c
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:31

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:692 (692.0 B)  TX bytes:692 (692.0 B)

Missing two network cards.

This is the contents of /etc/udev/rules.d/70-persistent-net.rules:

# PCI device 0x14e4:/sys/devices/root/f0069c00/pci0000:00/0000:00:02.0 (tg3)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:14:4f:8f:ca:5a", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" 

# PCI device 0x14e4:/sys/devices/root/f00859d4/pci0003:00/0003:00:02.0 (tg3)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:14:4f:8f:ca:5c", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" 

And this is what I get when I run lspci:
0000:00:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet 0000:00:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet 0001:00:06.0 Non-VGA unclassified device: ULi Electronics Inc. M7101 Power Management Controller [PMU] 0001:00:07.0 ISA bridge: ULi Electronics Inc. M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+] 0001:00:0a.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03) 
0001:00:0d.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c4)
0002:00:02.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 66MHz Ultra3 SCSI Adapter (rev 01) 0002:00:02.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 66MHz Ultra3 SCSI Adapter (rev 01) 0003:00:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet 0003:00:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet 

So, the system really gots 4 network cards but only see two of them.

Can anyone tell me how I can do to get all 4 network cards functionals?

Thanks a lot and best regards.

Maur.
Reply to: