Sun Fire V210 NIC's don't work
Hi,
I attempted to configure a second nic on my server and added the new
config to the /etc/network/interfaces file however I am left with dmesg
errors:
[ 44.418128] tg3 0003:00:02.0: eth1: Tigon3 [partno(none) rev 2100]
(PCI:66MHz:64-bit) MAC address 00:14:4f:5d:1e:80
[ 44.555470] tg3 0003:00:02.0: eth1: attached PHY is 5704
(10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 44.675644] tg3 0003:00:02.0: eth1: RXcsums[1] LinkChgREG[0] MIirq[0]
ASF[0] TSOcap[1]
[ 44.779719] tg3 0003:00:02.0: eth1: dma_rwctrl[763f0000] dma_mask[32-bit]
[ 91.472697] tg3 0003:00:02.0: eth1: Failed to load firmware
"tigon/tg3_tso.bin"
[ 91.568824] tg3 0003:00:02.0: eth1: TSO capability disabled
[ 92.927145] tg3 0003:00:02.0: eth1: No firmware running
[ 93.034647] ADDRCONF(NETDEV_UP): eth1: link is not ready
[31557.037820] tg3 0003:00:02.0: eth1: Failed to load firmware
"tigon/tg3_tso.bin"
[31557.134305] tg3 0003:00:02.0: eth1: TSO capability disabled
[31558.558344] ADDRCONF(NETDEV_UP): eth1: link is not ready
[31734.774354] tg3 0003:00:02.0: eth1: Failed to load firmware
"tigon/tg3_tso.bin"
[31734.870823] tg3 0003:00:02.0: eth1: TSO capability disabled
[31736.351600] ADDRCONF(NETDEV_UP): eth1: link is not ready
The switch which the port is connected to shows physical link and is
provisioned properly for the correct vlan, the first NIC eth0 is also
connected to the same switch and is working fine but still producing errors:
[ 42.672840] tg3 0000:00:02.0: eth0: Tigon3 [partno(none) rev 2100]
(PCI:66MHz:64-bit) MAC address 00:14:4f:5d:1e:7e
[ 42.810136] tg3 0000:00:02.0: eth0: attached PHY is 5704
(10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 42.930317] tg3 0000:00:02.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0]
ASF[0] TSOcap[1]
[ 43.034393] tg3 0000:00:02.0: eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[ 81.804867] tg3 0000:00:02.0: eth0: Failed to load firmware
"tigon/tg3_tso.bin"
[ 81.901028] tg3 0000:00:02.0: eth0: TSO capability disabled
[ 83.261266] tg3 0000:00:02.0: eth0: No firmware running
[ 84.321904] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 84.921250] tg3 0000:00:02.0: eth0: Link is up at 100 Mbps, full duplex
[ 85.008173] tg3 0000:00:02.0: eth0: Flow control is off for TX and
off for RX
[ 85.103732] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
I have tried loading the firmware from:
http://wiki.debian.org/Firmware
and putting it into /lib/firmware/tigon however then both NICs fail??
Could anyone suggest anything? With any other OS the system is fine so
I'm guessing it's a kernel bug or so.....
Regards,
Kaya
Reply to: