Re: SunFire V120 and sym53c8xx (was Re: Unofficial Squeeze installer image available)
On Thu, Feb 10, 2011 at 10:49:39AM +0000, Richard Mortimer wrote:
> [Cc'd to 611314@bugs.debian.org]
>
> On 10/02/2011 08:36, Jurij Smakov wrote:
> >On Wed, Feb 09, 2011 at 11:07:49PM +0000, Richard Mortimer wrote:
> >>On 09/02/2011 21:43, Jurij Smakov wrote:
> ... snip ...
> >>>
> >>>http://www.wooyd.org/debian/squeeze/
> >>>
> ...
> >
> >Sure, I have just uploaded a netboot image to the same location.
> >
> >>>If you have encountered problems during Squeeze installation, please
> >>>test this image and report the results, as a positive confirmation of
> >>>fixes on a variety of different systems is essential for getting all
> >>>these fixes into the first Squeeze point release.
> >>>
> >>I did spot a couple of issues with the installer when I gave squeeze
> >>a try a couple of weeks back. I only got chance to file an
> >>installation report about one of them
> >>http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=611314
> >>Its not a massive show stopper and has an easy workaround but if
> >>that can be fixed then it will make others lives easier.
> >
> >Yeah, this bug was pointed out to me just yesterday. I don't know
> >what's going on there yet, it appears that the PCI IDs of your
> >card match the ones which are supported by the driver, so if module is
> >not loaded at all there is probably something wrong with udev. At a
> >point where it says it cannot detect the disks, can you drop back to
> >shell and see whether the driver actually isn't loaded (as opposed to
> >being loaded but failing to find the disks anyway)? Maybe there is
> >something relevant showing up in dmesg or /var/log/messages?
> >
> >If not, I'll try to come up with some udev debugging commands to try
> >and understand why this detection is failing.
>
> I tested with your netboot image and it exhibits the same behaviour
> as the official installer. The sym53c8xx driver does get loaded
> automatically. I'm pretty sure that this is a timing issue. I
> confirmed that all of the /dev/sd* files were present along with
> /dev/disk/* entries.
Ok, I think the magic happens in the disk_found() function in
disk-detect.sh [0]. It looks like it will retry up to 3 times to see
whether devices have showed up (with list-devices disk), sleeping 2
seconds between attempts... If it takes up to 7 seconds for driver to
initialize itself, we might be cutting it just a bit too short.
Unfortunately, I don't see how we can test it easily, as neither
netboot image nor miniiso contain the udebs, they are downloaded off
the network.
[0] http://git.debian.org/?p=d-i/hw-detect.git;a=blob_plain;f=disk-detect.sh;hb=HEAD
> Looking at the dmesg output I can see a 7 second delay whilst the
> driver/scsi subsystem settles itself down. (I also see a similar
> issue when I boot after install with raid/lvm setup - but both
> rootdelay & the scsi probe sync option fixes that). After dropping
> to the installer shell I can re-enter the "Detect disks" screen and
> it find them without problem.
>
> Regards
>
> Richard
>
>
> Full console output below just in case it is useful.
>
>
>
> BusyBox v1.17.1 (Debian 1:1.17.1-8) built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> ~ #
> ~ # lsmod
> Module Size Used by
> sd_mod 31548 0
> crc_t10dif 1292 1 sd_mod
> ata_generic 3199 0
> libata 147511 1 ata_generic
> sym53c8xx 71569 0
> scsi_transport_spi 20705 1 sym53c8xx
> alim15x3 4002 0
> usb_storage 41983 0
> scsi_mod 132037 5
> sd_mod,libata,sym53c8xx,scsi_transport_spi,usb_storage
> ohci_hcd 18603 0
> uhci_hcd 20343 0
> ehci_hcd 33777 0
> sungem 25663 0
> usbcore 117062 5 usb_storage,ohci_hcd,uhci_hcd,ehci_hcd
> nls_base 6649 1 usbcore
> sungem_phy 9430 1 sungem
> ~ #
> ~ # ls /dev
> block shm tty42
> bsg stderr tty43
> bus stdin tty44
> char stdout tty45
> console tty tty46
> core tty0 tty47
> cpu_dma_latency tty1 tty48
> disk tty10 tty49
> fd tty11 tty5
> full tty12 tty50
> input tty13 tty51
> kmsg tty14 tty52
> log tty15 tty53
> loop0 tty16 tty54
> mdesc tty17 tty55
> mem tty18 tty56
> net tty19 tty57
> network_latency tty2 tty58
> network_throughput tty20 tty59
> null tty21 tty6
> openprom tty22 tty60
> port tty23 tty61
> ppp tty24 tty62
> psaux tty25 tty63
> ptmx tty26 tty7
> pts tty27 tty8
> random tty28 tty9
> rtc0 tty29 ttyS0
> sda tty3 ttyS1
> sda1 tty30 urandom
> sda2 tty31 vcs
> sda3 tty32 vcs1
> sda7 tty33 vcs2
> sdb tty34 vcs3
> sdb1 tty35 vcs4
> sdb2 tty36 vcsa
> sdb3 tty37 vcsa1
> sdb4 tty38 vcsa2
> sdb5 tty39 vcsa3
> sdb6 tty4 vcsa4
> sdb7 tty40 vga_arbiter
> sdb8 tty41 zero
> ~ # ls -l /dev/sd*
> brw-rw-rw- 1 root root 8, 0 Feb 10 10:20 /dev/sda
> brw-rw-rw- 1 root root 8, 1 Feb 10 10:20 /dev/sda1
> brw-rw-rw- 1 root root 8, 2 Feb 10 10:20 /dev/sda2
> brw-rw-rw- 1 root root 8, 3 Feb 10 10:20 /dev/sda3
> brw-rw-rw- 1 root root 8, 7 Feb 10 10:20 /dev/sda7
> brw-rw-rw- 1 root root 8, 16 Feb 10 10:20 /dev/sdb
> brw-rw-rw- 1 root root 8, 17 Feb 10 10:20 /dev/sdb1
> brw-rw-rw- 1 root root 8, 18 Feb 10 10:20 /dev/sdb2
> brw-rw-rw- 1 root root 8, 19 Feb 10 10:20 /dev/sdb3
> brw-rw-rw- 1 root root 8, 20 Feb 10 10:20 /dev/sdb4
> brw-rw-rw- 1 root root 8, 21 Feb 10 10:20 /dev/sdb5
> brw-rw-rw- 1 root root 8, 22 Feb 10 10:20 /dev/sdb6
> brw-rw-rw- 1 root root 8, 23 Feb 10 10:20 /dev/sdb7
> brw-rw-rw- 1 root root 8, 24 Feb 10 10:20 /dev/sdb8
> ~ # ls -l /dev/disk/
> drwxr-xr-x 2 root root 280 Feb 10 10:20 by-id
> drwxr-xr-x 2 root root 280 Feb 10 10:20 by-path
> drwxr-xr-x 2 root root 60 Feb 10 10:20 by-uuid
> ~ # ls -l /dev/disk/*
> /dev/disk/by-id:
> lrwxrwxrwx 1 root root 9 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436 -> ../../sdb
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part1 -> ../../sdb1
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part2 -> ../../sdb2
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part4 -> ../../sdb4
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part5 -> ../../sdb5
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part6 -> ../../sdb6
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part7 -> ../../sdb7
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-1HITACHI_DK32EJ-14NC_404W3436-part8 -> ../../sdb8
> lrwxrwxrwx 1 root root 9 Feb 10 10:20
> scsi-SSEAGATE_ST318404LSUN18G3BT064HY000010431618 -> ../../sda
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-SSEAGATE_ST318404LSUN18G3BT064HY000010431618-part1 ->
> ../../sda1
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-SSEAGATE_ST318404LSUN18G3BT064HY000010431618-part2 ->
> ../../sda2
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> scsi-SSEAGATE_ST318404LSUN18G3BT064HY000010431618-part7 ->
> ../../sda7
>
> /dev/disk/by-path:
> lrwxrwxrwx 1 root root 9 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:0:0 -> ../../sda
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:0:0-part1 -> ../../sda1
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:0:0-part2 -> ../../sda2
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:0:0-part7 -> ../../sda7
> lrwxrwxrwx 1 root root 9 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0 -> ../../sdb
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part1 -> ../../sdb1
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part2 -> ../../sdb2
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part4 -> ../../sdb4
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part5 -> ../../sdb5
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part6 -> ../../sdb6
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part7 -> ../../sdb7
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> pci-0000:02:08.0-scsi-0:0:1:0-part8 -> ../../sdb8
>
> /dev/disk/by-uuid:
> lrwxrwxrwx 1 root root 10 Feb 10 10:20
> b58ad5ab-b4e8-40a5-9d5b-b2cabb7eb8b1 -> ../../sdb4
> ~ #
> ~ # lspci
> 00:01.0 PCI bridge: Oracle Corporation Simba Advanced PCI Bridge (rev 13)
> 00:01.1 PCI bridge: Oracle Corporation Simba Advanced PCI Bridge (rev 13)
> 01:03.0 Non-VGA unclassified device: ALi Corporation M7101 Power
> Management Controller [PMU]
> 01:05.1 Ethernet controller: Oracle Corporation RIO 10/100 Ethernet
> [eri] (rev 01)
> 01:05.3 USB Controller: Oracle Corporation RIO USB (rev 01)
> 01:07.0 ISA bridge: ALi Corporation M1533/M1535/M1543 PCI to ISA
> Bridge [Aladdin IV/V/V+]
> 01:0c.0 Bridge: Oracle Corporation RIO EBUS (rev 01)
> 01:0c.1 Ethernet controller: Oracle Corporation RIO 10/100 Ethernet
> [eri] (rev 01)
> 01:0c.3 USB Controller: Oracle Corporation RIO USB (rev 01)
> 01:0d.0 IDE interface: ALi Corporation M5229 IDE (rev c3)
> 02:05.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
> 1.1 Controller (rev 61)
> 02:05.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
> 1.1 Controller (rev 61)
> 02:05.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
> 02:05.3 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8
> [Fire II(M)] IEEE 1394 OHCI Controller (rev 46)
> 02:08.0 SCSI storage controller: LSI Logic / Symbios Logic
> 53C896/897 (rev 07)
> 02:08.1 SCSI storage controller: LSI Logic / Symbios Logic
> 53C896/897 (rev 07)
> ~ #
>
>
>
> [ 200.468985] mice: PS/2 mouse device common for all mice
> [ 200.538418] rtc-m48t59 rtc-m48t59.0: rtc core: registered m48t59 as rtc0
> [ 200.628329] TCP cubic registered
> [ 200.671447] NET: Registered protocol family 10
> [ 200.732131] lo: Disabled Privacy Extensions
> [ 200.788794] Mobile IPv6
> [ 200.820869] NET: Registered protocol family 17
> [ 200.879755] registered taskstats version 1
> [ 200.934254] rtc-m48t59 rtc-m48t59.0: setting system clock to
> 2011-02-10 10:16:44 UTC (1297333004)
> [ 201.051070] Initalizing network drop monitor service
> [ 201.711894] usbcore: registered new interface driver usbfs
> [ 201.791254] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
> [ 201.876037] PCI: Enabling device: (0000:01:0c.1), cmd 146
> [ 201.877133] usbcore: registered new interface driver hub
> [ 201.949086] PHY ID: 437421, addr: 1
> [ 201.952526] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet
> 00:03:ba:2d:9e:0c
> [ 202.044179] eth0: Found Generic MII PHY
> [ 202.096002] usbcore: registered new device driver usb
> [ 202.177753] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 202.267647] PHY ID: 437421, addr: 1
> [ 202.271488] eth1: Sun GEM (PCI) 10/100/1000BaseT Ethernet
> 00:03:ba:2d:9e:0d
> [ 202.363094] eth1: Found Generic MII PHY
> [ 202.414713] PCI: Enabling device: (0000:02:05.2), cmd 2
> [ 202.414741] ehci_hcd 0000:02:05.2: EHCI Host Controller
> [ 202.484009] ehci_hcd 0000:02:05.2: new USB bus registered,
> assigned bus number 1
> [ 202.633387] ehci_hcd 0000:02:05.2: Enabling legacy PCI PM
> [ 202.707958] ehci_hcd 0000:02:05.2: irq 14, io mem 0x1ff0000a000
> [ 202.839880] ehci_hcd 0000:02:05.2: USB 2.0 started, EHCI 1.00
> [ 202.916606] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 203.005972] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 203.101045] usb usb1: Product: EHCI Host Controller
> [ 203.165333] usb usb1: Manufacturer: Linux 2.6.32-5-sparc64 ehci_hcd
> [ 203.247778] usb usb1: SerialNumber: 0000:02:05.2
> [ 203.310069] usb usb1: configuration #1 chosen from 1 choice
> [ 203.384212] hub 1-0:1.0: USB hub found
> [ 203.434393] hub 1-0:1.0: 4 ports detected
> [ 203.501542] uhci_hcd: USB Universal Host Controller Interface driver
> [ 203.602188] PCI: Enabling device: (0000:02:05.0), cmd 1
> [ 203.602227] uhci_hcd 0000:02:05.0: UHCI Host Controller
> [ 203.681193] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 203.766667] uhci_hcd 0000:02:05.0: new USB bus registered,
> assigned bus number 2
> [ 203.864910] PCI: Enabling device: (0000:01:0c.3), cmd 2
> [ 203.864948] ohci_hcd 0000:01:0c.3: OHCI Host Controller
> [ 203.934099] ohci_hcd 0000:01:0c.3: new USB bus registered,
> assigned bus number 3
> [ 204.032201] uhci_hcd 0000:02:05.0: irq 12, io base 0x1fe02c00200
> [ 204.111891] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
> [ 204.201175] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 204.296244] usb usb2: Product: UHCI Host Controller
> [ 204.360398] usb usb2: Manufacturer: Linux 2.6.32-5-sparc64 uhci_hcd
> [ 204.443112] eth0: Link is up at 100 Mbps, full-duplex.
> [ 204.510707] usb usb2: SerialNumber: 0000:02:05.0
> [ 204.572320] ohci_hcd 0000:01:0c.3: irq 7, io mem 0x1ffe2000000
> [ 204.650168] usb usb2: configuration #1 chosen from 1 choice
> [ 204.723753] eth1: Link is up at 100 Mbps, full-duplex.
> [ 204.796468] hub 2-0:1.0: USB hub found
> [ 204.845805] hub 2-0:1.0: 2 ports detected
> [ 204.899404] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
> [ 204.988762] usb usb3: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 205.083852] usb usb3: Product: OHCI Host Controller
> [ 205.147981] usb usb3: Manufacturer: Linux 2.6.32-5-sparc64 ohci_hcd
> [ 205.230464] usb usb3: SerialNumber: 0000:01:0c.3
> [ 205.292050] PCI: Enabling device: (0000:02:05.1), cmd 1
> [ 205.292079] uhci_hcd 0000:02:05.1: UHCI Host Controller
> [ 205.361767] usb usb3: configuration #1 chosen from 1 choice
> [ 205.436254] hub 3-0:1.0: USB hub found
> [ 205.485581] hub 3-0:1.0: 4 ports detected
> [ 205.539131] uhci_hcd 0000:02:05.1: new USB bus registered,
> assigned bus number 4
> [ 205.636981] PCI: Enabling device: (0000:01:05.3), cmd 2
> [ 205.637014] ohci_hcd 0000:01:05.3: OHCI Host Controller
> [ 205.706604] ohci_hcd 0000:01:05.3: new USB bus registered,
> assigned bus number 5
> [ 205.804356] uhci_hcd 0000:02:05.1: irq 13, io base 0x1fe02c00220
> [ 205.884207] ohci_hcd 0000:01:05.3: irq 10, io mem 0x1ffe5000000
> [ 205.962888] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
> [ 206.052196] usb usb4: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 206.147258] usb usb4: Product: UHCI Host Controller
> [ 206.211407] usb usb4: Manufacturer: Linux 2.6.32-5-sparc64 uhci_hcd
> [ 206.293889] usb usb4: SerialNumber: 0000:02:05.1
> [ 206.360014] usb usb4: configuration #1 chosen from 1 choice
> [ 206.434027] hub 4-0:1.0: USB hub found
> [ 206.483726] hub 4-0:1.0: 2 ports detected
> [ 206.537071] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
> [ 206.626452] usb usb5: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 206.721511] usb usb5: Product: OHCI Host Controller
> [ 206.785661] usb usb5: Manufacturer: Linux 2.6.32-5-sparc64 ohci_hcd
> [ 206.868146] usb usb5: SerialNumber: 0000:01:05.3
> [ 206.945846] usb usb5: configuration #1 chosen from 1 choice
> [ 207.020142] hub 5-0:1.0: USB hub found
> [ 207.074466] hub 5-0:1.0: 4 ports detected
> [ 255.161214] SCSI subsystem initialized
> [ 255.191455] Initializing USB Mass Storage driver...
> [ 255.191654] usbcore: registered new interface driver usb-storage
> [ 255.192726] USB Mass Storage support registered.
> [ 258.088311] eth0: Link is up at 100 Mbps, full-duplex.
> [ 258.088328] eth0: Pause is disabled
> [ 258.133052] eth1: Link is up at 100 Mbps, full-duplex.
> [ 258.133071] eth1: Pause is disabled
> [ 259.266698] eth0: Link is up at 100 Mbps, full-duplex.
> [ 259.266717] eth0: Pause is disabled
> [ 270.246218] eth0: Link is up at 100 Mbps, full-duplex.
> [ 270.246237] eth0: Pause is disabled
> [ 293.593968] lo: Disabled Privacy Extensions
> [ 293.629428] eth0: Link is up at 100 Mbps, full-duplex.
> [ 293.629445] eth0: Pause is disabled
> [ 311.225451] lo: Disabled Privacy Extensions
> [ 311.260996] eth0: Link is up at 100 Mbps, full-duplex.
> [ 311.261015] eth0: Pause is disabled
> [ 435.628895] alim15x3 0000:01:0d.0: IDE controller (0x10b9:0x5229
> rev 0xc3)
> [ 435.628935] PCI: Enabling device: (0000:01:0d.0), cmd 5
> [ 435.629060] alim15x3 0000:01:0d.0: 100% native mode on irq 8
> [ 435.629083] ide0: BM-DMA at 0x1fe02000420-0x1fe02000427
> [ 435.629152] ide1: BM-DMA at 0x1fe02000428-0x1fe0200042f
> [ 435.629206] Probing IDE interface ide0...
> [ 435.632190] ide0: no devices on the port
> [ 435.633249] Probing IDE interface ide1...
> [ 435.663719] PCI: Enabling device: (0000:02:08.0), cmd 147
> [ 435.880411] sym0: <896> rev 0x7 at pci 0000:02:08.0 irq 11
> [ 435.883300] sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
> [ 435.890503] sym0: SCSI BUS has been reset.
> [ 435.890564] scsi0 : sym-2.2.3
> [ 435.892106] PCI: Enabling device: (0000:02:08.1), cmd 147
> [ 436.108204] sym1: <896> rev 0x7 at pci 0000:02:08.1 irq 11
> [ 436.111533] sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
> [ 436.118701] sym1: SCSI BUS has been reset.
> [ 436.118775] scsi1 : sym-2.2.3
> [ 436.556103] ide0 at 0x1fe02000400-0x1fe02000407,0x1fe0200041a on irq 8
> [ 436.556158] ide1 at 0x1fe02000410-0x1fe02000417,0x1fe0200040a on irq 8
> [ 436.665718] libata version 3.00 loaded.
> [ 438.901946] scsi 0:0:0:0: Direct-Access SEAGATE
> ST318404LSUN18G 5221 PQ: 0 ANSI: 3
> [ 438.901985] scsi target0:0:0: tagged command queuing enabled,
> command queue depth 16.
> [ 438.902027] scsi target0:0:0: Beginning Domain Validation
> [ 438.910250] scsi target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25
> ns, offset 31)
> [ 438.913914] scsi target0:0:0: Domain Validation skipping write tests
> [ 438.913927] scsi target0:0:0: Ending Domain Validation
> [ 438.923619] scsi 0:0:1:0: Direct-Access HITACHI
> DK32EJ14NSUN146G PQ0B PQ: 0 ANSI: 3
> [ 438.923640] scsi target0:0:1: tagged command queuing enabled,
> command queue depth 16.
> [ 438.923673] scsi target0:0:1: Beginning Domain Validation
> [ 438.948952] scsi target0:0:1: FAST-40 WIDE SCSI 80.0 MB/s ST (25
> ns, offset 31)
> [ 438.961993] scsi target0:0:1: Domain Validation skipping write tests
> [ 438.962005] scsi target0:0:1: Ending Domain Validation
> [ 442.871430] sd 0:0:0:0: [sda] 35378533 512-byte logical blocks:
> (18.1 GB/16.8 GiB)
> [ 442.875606] sd 0:0:0:0: [sda] Write Protect is off
> [ 442.875623] sd 0:0:0:0: [sda] Mode Sense: cf 00 10 08
> [ 442.877279] sd 0:0:1:0: [sdb] 286739329 512-byte logical blocks:
> (146 GB/136 GiB)
> [ 442.878836] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
> enabled, supports DPO and FUA
> [ 442.883570] sda:
> [ 442.893149] sd 0:0:1:0: [sdb] Write Protect is off
> [ 442.893165] sd 0:0:1:0: [sdb] Mode Sense: fb 00 10 08
> [ 442.894816] sda1 sda2 sda3 sda7
> [ 442.900613] sd 0:0:1:0: [sdb] Write cache: disabled, read cache:
> enabled, supports DPO and FUA
> [ 442.904536] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 442.923823] sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
> [ 442.962062] sd 0:0:1:0: [sdb] Attached SCSI disk
> ~ #
>
>
> --
> To UNSUBSCRIBE, email to debian-sparc-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
> Archive: [🔎] 4D53C2C3.6080406@oldelvet.org.uk">http://lists.debian.org/[🔎] 4D53C2C3.6080406@oldelvet.org.uk
--
Jurij Smakov jurij@wooyd.org
Key: http://www.wooyd.org/pgpkey/ KeyID: C99E03CC
Reply to: