Re: Blade 100 and 2.6.{22,23}
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Luigi Gangitano schrieb:
> Hi sparcers,
> since last official debian kernel running on my SunBlade100 is
> 2.6.21-2, today I investigated what is going wrong in 2.6.22 and
> 2.6.23. Both kernels hang at boot with and without the
> video=atyfb:off parameter.
>
> A -p output of 2.6.23 follows, it seems that while scanning the PCI
> bus devices get added multiple times. For the record 0000:00:03.0 is
> the PMU and 07.0 is the ISA bridge.
>
> Any ideas?
>
> Regards,
>
> L
2.6.22 (linux-image-2.6.22-3-sparc64 2.6.22-6~bpo40+1) from bpo just
works here
here's my dmesg:
PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:31'
PROMLIB: Root node compatible:
Linux version 2.6.22-3-sparc64 (Debian 2.6.22-6~bpo40+1)
(nobse@backports.org) (gcc version 4.1.2 20061115 (prerelease) (Debian
4.1.1-21)) #1 Tue Nov 13 09:20:56 UTC 2007
ARCH: SUN4U
Ethernet address: 00:03:ba:0b:6e:fc
PROM: Built device tree with 60206 bytes of memory.
On node 0 totalpages: 130356
Normal zone: 894 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 129462 pages, LIFO batch:15
Built 1 zonelists. Total pages: 129462
Kernel command line: root=/dev/hda1 ro
PID hash table entries: 4096 (order: 12, 32768 bytes)
clocksource: mult[b40001] shift[16]
clockevent: mult[16c16bf] shift[32]
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 6, 524288 bytes)
Memory: 1020832k available (2392k kernel code, 840k data, 152k init)
[fffff80000000000,000000003fdf0000]
Calibrating delay using timer specific routine.. 11.11 BogoMIPS
(lpj=22225)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing for controllers.
/pci@1f,0: SABRE PCI Bus Module
/pci@1f,0: PCI IO[1fe02000000] MEM[1ff00000000]
PCI: Scanning PBM /pci@1f,0
PCI quirk: region 0800-083f claimed by ali7101 ACPI
PCI quirk: region 0600-061f claimed by ali7101 SMB
isa0: [dma -> (floppy) (parallel)] [power] [serial] [serial]
ebus0: [flashprom] [eeprom] [idprom]
power: Control reg at 1fe02000800 ... powerd running.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
/pci@1f,0/ebus@c/eeprom@1,0: Clock regs at 000001fff1000000
NET: Registered protocol family 2
Time: hbtick clocksource has been installed.
IP route cache hash table entries: 8192 (order: 3, 65536 bytes)
TCP established hash table entries: 32768 (order: 6, 524288 bytes)
TCP bind hash table entries: 32768 (order: 5, 262144 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5205k freed
audit: initializing netlink socket (disabled)
audit(1198183803.448:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
PCI: Enabling device: (0000:00:13.0), cmd 83
atyfb: 3D RAGE XL (Mach64 GR, PCI-33) [0x4752 rev 0x27]
atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL, 83 Mhz MCLK,
63 MHz XCLK
Console: switching to colour frame buffer device 160x64
atyfb: fb0: ATY Mach64 frame buffer device on PCI
rtc_init: no PC rtc found
[drm] Initialized drm 1.1.0 20060810
f007d64c: ttyS0 at MMIO 0x1fe020003f8 (irq = 9) is a 16550A
f007f1a4: ttyS1 at MMIO 0x1fe020002e8 (irq = 9) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
rtc_sun_init: Registered Mostek RTC driver.
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
PHY ID: 437421, addr: 1
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:ba:0b:6e:fc
eth0: Found Generic MII PHY
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <becker@scyld.com>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device: (0000:01:00.0), cmd 3
natsemi eth1: NatSemi DP8381[56] at 0x1ff03000000 (0000:01:00.0),
00:40:f4:3c:fa:e9, IRQ 16, port TP.
Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
firewire_ohci: Added fw-ohci device 0000:00:0c.2, OHCI version 1.0
PCI: Enabling device: (0000:01:01.0), cmd 3
tulip0: MII transceiver #1 config 1000 status 7809 advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 33 at Port 0x1fe02001100,
00:A0:CC:3B:41:74, IRQ 17.
PCI: Enabling device: (0000:01:02.0), cmd 3
tulip1: EEPROM default media type Autosense.
tulip1: Index #0 - Media 10baseT (#0) described by a 21140 non-MII
(0) block.
tulip1: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII
(0) block.
tulip1: Index #2 - Media 10baseT-FDX (#4) described by a 21140
non-MII (0) block.
tulip1: Index #3 - Media 100baseTx-FDX (#5) described by a 21140
non-MII (0) block.
tulip1: MII transceiver #1 config 3100 status 7809 advertising 05e1.
eth1: Digital DS21140 Tulip rev 34 at Port 0x1fe02001200,
00:40:33:A2:B1:76, IRQ 18.
ohci_hcd 0000:00:0c.3: OHCI Host Controller
ohci_hcd 0000:00:0c.3: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0c.3: irq 13, io mem 0x1ff02000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ALI15X3: IDE controller at PCI slot 0000:00:0d.0
PCI: Enabling device: (0000:00:0d.0), cmd 5
ALI15X3: chipset revision 195
ALI15X3: 100% native mode on irq 15
ide0: BM-DMA at 0x1fe02000a20-0x1fe02000a27, BIOS settings:
hda:pio, hdb:pio
ide1: BM-DMA at 0x1fe02000a28-0x1fe02000a2f, BIOS settings:
hdc:pio, hdd:pio
Probing IDE interface ide0...
firewire_core: created new fw device fw0 (0 config rom retries)
usb 1-3: new low speed USB device using ohci_hcd and address 2
hda: Hitachi HDS721680PLAT80, ATA DISK drive
usb 1-3: configuration #1 chosen from 1 choice
input: HID 0430:0005 as /class/input/input0
input: USB HID v1.00 Keyboard [HID 0430:0005] on usb-0000:00:0c.3-3
eth2: Link is up at 100 Mbps, full-duplex.
hdb: LTN486S, ATAPI CD/DVD-ROM drive
hda: selected mode 0x44
ide0 at 0x1fe02000a00-0x1fe02000a07,0x1fe02000a1a on irq 15
Probing IDE interface ide1...
SCSI subsystem initialized
libata version 2.21 loaded.
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/7376KiB Cache, CHS=16383/255/63,
UDMA(66)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: ATAPI 48X CD-ROM drive, 120kB Cache
Uniform CD-ROM driver Revision: 3.20
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
PCI: Enabling device: (0000:00:08.0), cmd 3
EXT3 FS on hda1, internal journal
Probing IDE interface ide1...
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth2: Link is up at 100 Mbps, full-duplex.
eth2: Pause is disabled
eth2: Link is up at 100 Mbps, full-duplex.
eth2: Pause is disabled
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth2: no IPv6 routers present
greets Uwe
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (MingW32)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iD8DBQFHatcfmDkRS+2sqmURAi6BAJwP5kQQOFYmUnPjHRnn32TsyxXKoACfex3R
M6AEMRHSWeTi0MK6lQVhc4Q=
=Gc8a
-----END PGP SIGNATURE-----
Reply to: