I'm having issues getting my sun blade 1000 to boot properly after configuring, compiling, and installing the 2.4.33.3 kernel. The old kernel (2.4.27) that installed with debian does boot correctly. When the new kernel boots, it has an issue when it uses fsck to check the filesystems. It says "No such file or directory when trying to open /dev/sda2fsck.ext3: /dev/sda2: No such file or directory". After it fails for all of the /dev/sda devices, it says to do a CONTROL-D to continue system startup, or give the root password for maintenance. At this point, CTRL+D or the root password do not do anything. The system appears to be frozen. If anybody has any advice on this issue I would appreciate it. The only thing that I can think of doing at this point is to upgrade to the 2.6 kernel. Attached is the output from dmesg (dmesg.txt) and lsmod (lsmod.txt) from the working kernel, and the configuration (kernel.config). Thanks to all in advance. Blake
PROMLIB: Sun IEEE Boot Prom 4.16.4 2004/12/18 05:18 Linux version 2.4.27-3-sparc64-smp (pbuilder@sparc) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP Thu Sep 14 06:25:40 UTC 2006 ARCH: SUN4U Ethernet address: 00:03:ba:10:0c:cd On node 0 totalpages: 261029 zone(0): 261869 pages. zone(1): 0 pages. zone(2): 0 pages. Found CPU 0 (node=f0060770,mid=0) Found CPU 1 (node=f0061108,mid=1) Found 2 CPU prom device tree node(s). Kernel command line: root=/dev/sda1 ro Console: colour dummy device 80x25 Calibrating delay loop... 499.71 BogoMIPS Memory: 2063584k available (2016k kernel code, 304k data, 168k init) [fffff80000000000,000000007fdda000] Dentry cache hash table entries: 262144 (order: 9, 4194304 bytes) Inode cache hash table entries: 131072 (order: 8, 2097152 bytes) Mount cache hash table entries: 512 (order: 0, 8192 bytes) Buffer cache hash table entries: 131072 (order: 7, 1048576 bytes) Page-cache hash table entries: 262144 (order: 8, 2097152 bytes) POSIX conformance testing by UNIFIX Entering UltraSMPenguin Mode... Calibrating delay loop... 499.71 BogoMIPS Total of 2 processors activated (999.42 BogoMIPS). CPU 1: synchronized TICK with master CPU (last diff 0 cycles,maxerr 5 cycles) Waiting on wait_init_idle (map = 0x2) All processors have done init_idle PCI: Probing for controllers. SCHIZO0 PBMB: ver[4:0], portid 8, cregs[40004400000] pregs[40004700000] SCHIZO0 PBMB: PCI CFG[7ffee000000] IO[7ffef000000] MEM[7fe00000000] SCHIZO0 PBMA: ver[4:0], portid 8, cregs[40004400000] pregs[40004600000] SCHIZO0 PBMA: PCI CFG[7ffec000000] IO[7ffed000000] MEM[7fd00000000] PCI-IRQ: Routing bus[ 0] slot[ 5] map[0] to INO[1d] PCI-IRQ: Routing bus[ 0] slot[ 5] map[0] to INO[1e] PCI-IRQ: Routing bus[ 0] slot[ 5] map[0] to INO[1f] PCI-IRQ: Routing bus[ 0] slot[ 6] map[0] to INO[18] PCI-IRQ: Routing bus[ 0] slot[ 6] map[0] to INO[19] PCI0(PBMB): Bus running at 33MHz PCI-IRQ: Routing bus[ 1] slot[ 4] map[0] to INO[04] PCI0(PBMA): Bus running at 66MHz ebus0: [flashprom] [i2c -> (nvram) (idprom) (dimm-fru) (dimm-fru) (dimm-fru) (dimm-fru) (dimm-fru) (dimm-fru) (dimm-fru) (dimm-fru)] [bbc] [ppm] [i2c -> (cpu-fru) (temperature) (cpu-fru) (temperature) (fan-control) (card-reader) (motherboard-fru) (i2c-bridge)] [beep] [audio] [rtc] [gpio] [pmc] [floppy] [parallel] [serial] SAB82532 serial driver version 1.65 ttyS00 at 0x7fe7e400000 (irq = 12,222) is a SAB82532 V3.2 ttyS01 at 0x7fe7e400040 (irq = 12,222) is a SAB82532 V3.2 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket chmc0: US3 memory controller at 0000040000400000 [ACTIVE] chmc1: US3 memory controller at 0000040000c00000 [ACTIVE] Starting kswapd VFS: Disk quotas vdquot_6.5.1 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Console: switching to colour frame buffer device 144x54 fb0: Elite 3D at 000007f800000000 type 35 DAC 0 kbd_init: Assuming USB keyboard. 8042(speaker): iobase[000007fe7e000032] pty: 256 Unix98 ptys configured Real Time Clock Driver v1.10f RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: registered new driver usbmouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver usbkbd usbkbd.c: :USB HID Boot Protocol keyboard driver mice: PS/2 mouse device common for all mice Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 16384 buckets, 256Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 2976 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done. Freeing initrd memory: 2976k freed VFS: Mounted root (cramfs filesystem). Unimplemented SPARC system call 188 Unimplemented SPARC system call 188 Unimplemented SPARC system call 188 Unimplemented SPARC system call 188 Unimplemented SPARC system call 188 Unimplemented SPARC system call 188 SCSI subsystem driver Revision: 1.00 sym.0.6.0: setting PCI_COMMAND_INVALIDATE. sym.0.6.1: setting PCI_COMMAND_INVALIDATE. sym0: <875> rev 0x37 on pci bus 0 device 6 function 0 irq 4,218 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: SCSI BUS has been reset. sym1: <875> rev 0x37 on pci bus 0 device 6 function 1 irq 4,219 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: SCSI BUS has been reset. scsi0 : sym-2.1.17a scsi1 : sym-2.1.17a Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1009 Type: CD-ROM ANSI SCSI revision: 02 qlogicfc0 : Could not read from NVRAM qlogicfc0 : Loop Reinitialized qlogicfc0 : Link is Up scsi2 : QLogic ISP2200 SCSI on PCI bus 01 device 20 irq 6927232 base 0x7ffed000300 qlogicfc0 : Port Database wwn: 200000e08b000000 scsi_id: 0 loop_id: 0 wwn: 21000011c6266960 scsi_id: 1 loop_id: 1 wwn: 21000011c62f9c60 scsi_id: 2 loop_id: 2 Vendor: SEAGATE Model: ST373453 CLAR72 Rev: 8A16 Type: Direct-Access ANSI SCSI revision: 03 Vendor: SEAGATE Model: ST373453 CLAR72 Rev: 8A16 Type: Direct-Access ANSI SCSI revision: 03 Attached scsi disk sda at scsi2, channel 0, id 1, lun 0 Attached scsi disk sdb at scsi2, channel 0, id 2, lun 0 SCSI device sda: 140174232 512-byte hdwr sectors (71769 MB) Partition check: /dev/scsi/host2/bus0/target1/lun0: p1 p2 p3 p4 p5 p6 p7 SCSI device sdb: 140174232 512-byte hdwr sectors (71769 MB) /dev/scsi/host2/bus0/target2/lun0: p1 p2 p3 Journalled Block Device driver loaded EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Adding Swap: 1047424k swap-space (priority -1) Adding Swap: 1728152k swap-space (priority -2) EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal sbp2: $Rev: 1074 $ Ben Collins <bcollins@debian.org> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1) Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 sym0:6: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 16) sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,17), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,4), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. ohci1394: $Rev: 1045 $ Ben Collins <bcollins@debian.org> ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[8,21e] MMIO=[7fe00120000-7fe001207ff] Max Packet=[2048] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0003bafffe100ccd] sungem.c:v0.97 3/20/02 David S. Miller (davem@redhat.com) eth%d: MII PHY ID: 18074c0 Lucent eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:ba:10:0c:cd usb-ohci.c: USB OHCI at membase 0x7fe01000000, IRQ 9,21f usb-ohci.c: usb-00:05.3, PCI device 108e:1103 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 4 ports detected hub.c: new USB device 00:05.3-3, assigned address 2 input0: USB HIDBP Mouse 0430:0100 on usb1:2.0 hub.c: new USB device 00:05.3-4, assigned address 3 input1: USB HIDBP Keyboard 0430:0005 on usb1:3.0 sys32_ioctl(usbmodules:501): Unknown cmd fd(3) cmd(c00c5512) arg(effff808) sys32_ioctl(usbmodules:501): Unknown cmd fd(3) cmd(c00c5512) arg(effff808) sys32_ioctl(usbmodules:501): Unknown cmd fd(3) cmd(c00c5512) arg(effff808) sys32_ioctl(usbmodules:510): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) sys32_ioctl(usbmodules:510): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) sys32_ioctl(usbmodules:510): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz> hid-core.c: USB HID support drivers sys32_ioctl(usbmodules:532): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:533): Unknown cmd fd(3) cmd(c00c5512) arg(effff828) sys32_ioctl(usbmodules:533): Unknown cmd fd(3) cmd(c00c5512) arg(effff828) sys32_ioctl(usbmodules:533): Unknown cmd fd(3) cmd(c00c5512) arg(effff828) sys32_ioctl(usbmodules:532): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:532): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:570): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) sys32_ioctl(usbmodules:570): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) sys32_ioctl(usbmodules:570): Unknown cmd fd(3) cmd(c00c5512) arg(effff7e8) sys32_ioctl(usbmodules:583): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:583): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:583): Unknown cmd fd(3) cmd(c00c5512) arg(effff7f8) sys32_ioctl(usbmodules:610): Unknown cmd fd(3) cmd(c00c5512) arg(effff748) sys32_ioctl(usbmodules:610): Unknown cmd fd(3) cmd(c00c5512) arg(effff748) eth0: MII PHY ID: 18074c0 Lucent eth0: Link is up at 100 Mbps, full-duplex. eth0: Pause is disabled
Module Size Used by Not tainted hid 17376 0 (unused) usb-ohci 21384 0 (unused) sungem 29064 1 crc32 3504 0 [sungem] ohci1394 29960 0 (unused) sr_mod 16644 0 (unused) cdrom 29184 0 [sr_mod] sbp2 17900 0 (unused) ieee1394 245272 0 [ohci1394 sbp2] ext3 92472 6 (autoclean) jbd 47528 6 (autoclean) [ext3] sd_mod 12816 16 (autoclean) qlogicfc 173008 8 (autoclean) sym53c8xx_2 78024 0 (autoclean) (unused) scsi_mod 99232 4 (autoclean) [sr_mod sbp2 sd_mod qlogicfc sym53c8xx_2]
Attachment:
kernel.config
Description: XML document