debian-31r0a-sparc-binary-1 install not booting correctly on ULTRA-10.
-- debian-31r0a-sparc-binary-1 install not booting correctly on ULTRA-10.
This is the sunULTRA 5/10 with single UltraSparc-IIi 333mHz CPU.
The OpenBoot is v3.19. There is 768MB of 50ns memory.
All stages of the background SS20 install of my previous post went
normally with the commands and errors showing on the black screen only
after booting. With the ULTRA-10 install the commands and errors
appered on the black screen right away:
FDC 0is a National Semiconductor Pc87306
RAMDISK driver initialized: 16 RAMDISKS of 16384k size 1024 blocksize
Uniform Multi-platform E-IDC driver
ide: Assuming Revision: 7.00beta4-24 33mHz system bus speed for
PIOmodes: override with idebus=xx
CMD646:IDE controller at PCI slot 01:030
CMD646:chipset revision 3
CMD646: 100% native modeon irq4.7c0
ide0:BM-DMA at 0x1fe02c00020-0xfe02 00027, BIOS settings:hdaighdb:pio
ide0:BM-DMA at 0x1fe02c00020-0xfe02 00027, BIOS settings:hdcighdd:pio
hda:ST391404A,ATA DISK drive
ide: Assuming 33mHz system bus speed for PIO modes:override
hdc: SONY CD-RW CRX300E ATAPI CD/DVD[ROM drive
ide0: at 0x1fe02c0000-0xife02c000070-1fe02c0000a on irq4.70
Partition check:
hda:end_request: I/O error, dev03:00(hda) sector2
hda:end_request: I/O error, dev03:00(hda) sector4
hda:end_request: I/O error, dev03:00(hda) sector6
hda:end_request: I/O error, dev03:00(hda) sector0
hda:end_request: I/O error, dev03:00(hda) sector10
hda:end_request: I/O error, dev03:00(hda) sector12
hda:end_request: I/O error, dev03:00(hda) sector14
hda:end_request: I/O error, dev03:00(hda) sector0
hda:end_request: I/O error, dev03:00(hda) sector2
hda:end_request: I/O error, dev03:00(hda) sector4
hda:end_request: I/O error, dev03:00(hda) sector6
hda:end_request: I/O error, dev03:00(hda) sector0
hda:end_request: I/O error, dev03:00(hda) sector10
hda:end_request: I/O error, dev03:00(hda) sector12
hda:end_request: I/O error, dev03:00(hda) sector14
unable to read the partition table
usb.c:required new driver usbdevfc
usb.c:required new driver hub
usb.c:required new driver usbmouse
usbmouse c:v1.6:USB HID Boot Protocol mousedriver
usb.c: registered new driver usbdevfs
..
initializing cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
RAMDISK: could not find valid RAMdisk image starting at 0
Freeing initrd memory 2970k freed
cramcis: wrong magic
kernel panic:UFS: unable to mount root fs om 00:00
Press Li-A to return to boot prompt
********************
What are the next steps after this bad result?
thanks
Don Parsons dfp10@capital.net
Reply to: