Принтер HP 1020 перестал работать после апгрейда с etch до lenny.
Привет.
"Сломался" принтер после апгрейда до lenny.
В чём может быть дело?
Прошивка грузиться нормально.
syslog
... usb 1-9: new high speed USB device using ehci_hcd and address 6
... usb 1-9: configuration #1 chosen from 1 choice
... usb 1-9: New USB device found, idVendor=03f0, idProduct=2b17
... usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3
... usb 1-9: Product: HP LaserJet 1020
... usb 1-9: Manufacturer: Hewlett-Packard
... usb 1-9: SerialNumber: FN01QZK
... usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2B17
... usbcore: registered new interface driver usblp
... /usr/sbin/hplj1020: foo2zjs: loading HP LaserJet 1020 firmware /usr/share/foo2zjs/firmware/sihp1020.dl to /dev/usb/lp0 ...
... /usr/sbin/hplj1020: foo2zjs: ... download successful.
% file /usr/share/foo2zjs/firmware/sihp1020.dl
/usr/share/foo2zjs/firmware/sihp1020.dl: HP Printer Job Language data
% ls -l /usr/share/foo2zjs/firmware/sihp1020.dl
-rw-rw-r-- 1 root root 128431 Янв 11 19:40 /usr/share/foo2zjs/firmware/sihp1020.dl
% usb_printerid /dev/usb/lp0
Error: Device or resource busy: can't open '/dev/usb/lp0'
или с 3-5 секундным таймаутом
% usb_printerid /dev/usb/lp0
Error: Input/output error: GET_DEVICE_ID on '/dev/usb/lp0'
usb_printerid пробовал и из дистрибутивного foo2zjs 20070718dfsg-9 и свежескаченного.
Ну и, естественно, не печатает.
При вкл. принтере, загружаемое ядро(2.6.26-1-686, впрочем и 2.6.24 от etch c половиной) пишет сл.:
[ 63.756033] usb 1-9: device descriptor read/64, error -110
[ 63.976082] usb 1-9: new high speed USB device using ehci_hcd and address 4
[ 69.000159] usb 1-9: device descriptor read/8, error -110
[ 74.124137] usb 1-9: device descriptor read/8, error -110
[ 74.344442] usb 1-9: new high speed USB device using ehci_hcd and address 5
[ 79.368105] usb 1-9: device descriptor read/8, error -110
[ 84.492072] usb 1-9: device descriptor read/8, error -110
[ 84.600339] hub 1-0:1.0: unable to enumerate USB device on port 9
На тех же портах (пробовал несколько) нормально работают флеська и сканер.
Принтер и кабель в рабочем состоянии, проверил на винде.
Вот ещё данные.
% cat /proc/bus/usb/devices
Т: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 2.06
S: Manufacturer=Linux 2.6.26-1-686 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:02.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=ff MxPS= 8 #Cfgs= 1
P: Vendor=04a9 ProdID=2220 Rev= 1.00
S: Manufacturer=Canon
S: Product=CanoScan
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=16ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.26-1-686 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:02.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=03f0 ProdID=2b17 Rev= 1.00
S: Manufacturer=Hewlett-Packard
S: Product=HP LaserJet 1020
S: SerialNumber=FN01QZK
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 98mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
% mount | grep usb
procbususb on /proc/bus/usb type usbfs (rw)
% lsmod | grep usb
usblp 10592 1
usbcore 118160 5 usblp,ohci_hcd,ehci_hcd
% lsmod | egrep '(usb|hcd)'
usblp 10592 0
ohci_hcd 18500 0
ehci_hcd 28428 0
usbcore 118160 4 usblp,ohci_hcd,ehci_hcd
% dmesg | grep hcd
[ 2.332528] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 2.336002] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 2.339533] ehci_hcd 0000:00:02.1: debug port 1
[ 2.343165] ehci_hcd 0000:00:02.1: irq 23, io mem 0xf1004000
[ 2.355660] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.375001] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.502999] usb usb1: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.517015] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 2.520436] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 2.523943] ohci_hcd 0000:00:02.0: irq 22, io mem 0xf1002000
[ 2.707182] usb usb2: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 2.749243] usb 1-9: new high speed USB device using ehci_hcd and address 2
[ 33.428008] usb 1-9: new high speed USB device using ehci_hcd and address 3
[ 63.976082] usb 1-9: new high speed USB device using ehci_hcd and address 4
[ 74.344442] usb 1-9: new high speed USB device using ehci_hcd and address 5
[ 84.920051] usb 2-9: new full speed USB device using ohci_hcd and address 2
[ 115.668030] usb 2-9: new full speed USB device using ohci_hcd and address 3
[ 146.416030] usb 2-9: new full speed USB device using ohci_hcd and address 4
[ 156.840057] usb 2-9: new full speed USB device using ohci_hcd and address 5
[ 3266.872034] usb 1-9: new high speed USB device using ehci_hcd and address 6
[ 5532.636036] usb 2-1: new full speed USB device using ohci_hcd and address 6
% lspci | grep -i usb
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
--
С Уважением,
Андрей Никитин
Reply to: