Re: bttv

[ivan <pravo@hnet.ru>]

Уважаемый Андрей,
нельзя ли мне пояснить, что тут в выводе:
# modinfo bttv | grep ^parm
parm:           debug:int
parm:           repeat_delay:int
parm:           repeat_period:int
parm:           ir_rc5_remote_gap:int
parm:           ir_rc5_key_timeout:int
parm:           i2c_debug:int
parm:           i2c_hw:configure i2c debug level (int)
parm:           i2c_scan:scan i2c bus at insmod time (int)
parm:           i2c_udelay:soft i2c delay at insmod time, in usecs 
(should be 5
or higher). Lower value means higher bus speed. (int)
parm:           vbibufs:number of vbi buffers, range 2-32, default 4 (int)
parm:           vbi_debug:vbi code debug messages, default is 0 (no) (int)
parm:           gpiomask:int
parm:           audioall:int
parm:           svhs:array of int
parm:           remote:array of int
parm:           audiomux:array of int
parm:           triton1:set ETBF pci config bit [enable bug 
compatibility for tr
iton1 + others] (int)
parm:           vsfx:set VSFX pci config bit [yet another chipset flaw 
workaroun
d] (int)
parm:           latency:pci latency timer (int)
parm:           card:specify TV/grabber card model, see CARDLIST file 
for a list
 (array of int)
parm:           pll:specify installed crystal (0=none, 28=28 MHz, 35=35 
MHz) (ar
ray of int)
parm:           tuner:specify installed tuner type (array of int)
parm:           autoload:automatically load i2c modules like tuner.o, 
default is
 1 (yes) (int)
parm:           no_overlay:allow override overlay default (0 disables, 1 
enables
) [some VIA/SIS chipsets are known to have problem with overlay] (int)
parm:           debug_latency:int
parm:           fdsr:int
parm:           video_nr:int
parm:           radio_nr:int
parm:           vbi_nr:int
parm:           v4l2:int
parm:           combfilter:int
parm:           lumafilter:int
parm:           radio:The TV card supports radio, default is 0 (no) 
(array of in
t)
parm:           bigendian:byte order of the framebuffer, default is 
native endia
n (int)
parm:           bttv_verbose:verbose startup messages, default is 1 
(yes) (int)
parm:           bttv_gpio:log gpio changes, default is 0 (no) (int)
parm:           bttv_debug:debug messages, default is 0 (no) (int)
parm:           irq_debug:irq handler debug messages, default is 0 (no) 
(int)
parm:           gbuffers:number of capture buffers. range 2-32, default 
8 (int)
parm:           gbufsize:size of the capture buffers, default is 
0x208000 (int)
parm:           reset_crop:reset cropping parameters at open(), default 
is 1 (ye 
            s) for compatibility with older applications (int)
parm:           automute:mute audio on bad/missing video signal, default 
is 1 (y 
           es) (int)
parm:           chroma_agc:enables the AGC of chroma signal, default is 
0 (no) ( 
            int)
parm:           adc_crush:enables the luminance ADC crush, default is 1 
(yes) (i 
            nt)
parm:           whitecrush_upper:sets the white crush upper value, 
default is 20 
                 7 (int)
parm:           whitecrush_lower:sets the white crush lower value, 
default is 12 
                 7 (int)
parm:           vcr_hack:enables the VCR hack (improves synch on poor 
VCR tapes) 
              , default is 0 (no) (int)
parm:           irq_iswitch:switch inputs in irq handler (int)
parm:           uv_ratio:ratio between u and v gains, default is 50 (int)
parm:           full_luma_range:use the full luma range, default is 0 
(no) (int)
parm:           coring:set the luma coring level, default is 0 (no) (int)