на какой пакет слать репорт: звук не работает в lenny, но работает в etch на ноутбуке toshiba satellite a30
Привет всем.
Спросил[1] уже в debian-user но там молчат.
Здесь я тоже спрашивал[2], но появилась дополнительная информация.
[1] http://comments.gmane.org/gmane.linux.debian.user/357826
[2] http://permalink.gmane.org/gmane.linux.debian.user.russian/81493
Звук не работает в Debian Lenny, но работает в Debian Etch.
Железо: Toshiba Satellite a30 (lspci in attachment), звуковая карта ATI
Technologies Inc IXP150 AC'97 Audio Controller.
Часто первый раз после загрузки, после начала проигрывания звука на
Debian Lenny, звук работает какое-то время. Затем xfmedia/totem виснет ,
mplayer печатает что-нить такое в цикле:
[AO_ALSA] alsa-lib: pcm_hw.c:405:(snd_pcm_hw_hwsync)
SNDRV_PCM_IOCTL_HWSYNC failed: Broken pipe
Это не происходит в Debian Etch.
Сначала я думал это проблемы кернела, потому что при загрузке я получаю
такие сообщения (полный dmesg в атаче):
MP-BIOS bug: 8254 timer not connected to IO-APIC
..trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
[snip]
atiixp: codec reset timeout
atiixp-modem: no codec available
После экспериментирования, я обнаружил что звук работает если добавить
опцию "acpi=off". Другие опции noapic, acpi={noirq,strict,force},
pci=noacpi, nolapic_timer не работают.
Использовать acpi=off не очень хочется потому что ноутбук.
Эти сообщения появляются и с "acpi=off".
Ядро 2.6.29 (из lenny-backports) не спасло. К тому же машина лочится
через какое-то время.
Тогда я поставил Debian Etch на отдельный раздел и в нём звук заработал
без проблем, и с 2.6.18 и с 2.6.24.
Тогда я поставил 2.6.18 и 2.6.24 из Etch в Debian Lenny (добавил Etch в
sources.list). Но это не помогло! Я получил ту же проблему в Debian
Lenny с ядром 2.6.18 и с 2.6.24!
То есть это похоже не (только?) ядерная проблема. Но чья? Alsa-lib? Куда
баг репортить?
Идеи приветствуются.
--
Best regards, Sergey Spiridonov
00:00.0 Host bridge: ATI Technologies Inc RS300 Host Bridge (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01)
00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01)
00:13.2 USB Controller: ATI Technologies Inc EHCI USB Controller (rev 01)
00:14.0 SMBus: ATI Technologies Inc SMBus (rev 17)
00:14.1 IDE interface: ATI Technologies Inc Dual Channel Bus Master PCI IDE Controller
00:14.3 ISA bridge: ATI Technologies Inc Device 434c
00:14.4 PCI bridge: ATI Technologies Inc IXP200 3COM 3C920B Ethernet Controller
00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01)
01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP [Radeon Mobility 9100IGP]
02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-15lenny3) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu May 28 15:39:35 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bf60000 (usable)
[ 0.000000] BIOS-e820: 000000001bf60000 - 000000001bf6d000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001bf6d000 - 000000001bf80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 447MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f6700] 000f6700
[ 0.000000] Entering add_active_range(0, 0, 114528) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114528
[ 0.000000] HighMem 114528 -> 114528
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114528
[ 0.000000] On node 0 totalpages: 114528
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 863 pages used for memmap
[ 0.000000] Normal zone: 109569 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6770, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 1BF68101, 0038 (r1 PTLTD RSDT 6040000 LTP 0)
[ 0.000000] ACPI: FACP 1BF6CF32, 0074 (r1 TOSCPL Chinook 6040000 ATI 3)
[ 0.000000] ACPI: DSDT 1BF689B5, 457D (r1 TOSCPL SB200 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 1BF7FFC0, 0040
[ 0.000000] ACPI: APIC 1BF6CFA6, 005A (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: SSDT 1BF68540, 032B (r1 PmRef Cpu0Ist 3000 INTL 20030224)
[ 0.000000] ACPI: SSDT 1BF68334, 020C (r1 PmRef Cpu0Cst 3001 INTL 20030224)
[ 0.000000] ACPI: SSDT 1BF68139, 01FB (r1 PmRef CpuPm 3000 INTL 20030224)
[ 0.000000] ACPI: DMI detected: Toshiba
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 2c000000:d2c00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d8000
[ 0.000000] PM: Registered nosave memory: 00000000000d8000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113633
[ 0.000000] Kernel command line: root=/dev/mapper/messenger_main-root ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1600.141 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 442948k/458112k available (1769k kernel code, 14644k reserved, 752k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdbf60000 ( 447 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba5eb - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba5eb (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084163] Calibrating delay using timer specific routine.. 3204.15 BogoMIPS (lpj=6408304)
[ 0.084228] Security Framework initialized
[ 0.084236] SELinux: Disabled at boot.
[ 0.084243] Capability LSM initialized
[ 0.084270] Mount-cache hash table entries: 512
[ 0.084532] Initializing cgroup subsys ns
[ 0.084540] Initializing cgroup subsys cpuacct
[ 0.084545] Initializing cgroup subsys devices
[ 0.084580] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.084586] CPU: L2 cache: 512K
[ 0.084590] CPU: Hyper-Threading is disabled
[ 0.084596] Intel machine check architecture supported.
[ 0.084606] Intel machine check reporting enabled on CPU#0.
[ 0.084611] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[ 0.084618] CPU0: Thermal monitoring enabled
[ 0.084643] Checking 'hlt' instruction... OK.
[ 0.100634] SMP alternatives: switching to UP code
[ 0.115372] Freeing SMP alternatives: 16k freed
[ 0.115380] ACPI: Core revision 20080321
[ 0.134264] ENABLING IO-APIC IRQs
[ 0.134458] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.136008] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 0.136008] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 0.136008] ...trying to set up timer as Virtual Wire IRQ... works.
[ 0.177927] CPU0: Intel Mobile Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[ 0.180011] Brought up 1 CPUs
[ 0.180011] Total of 1 processors activated (3204.15 BogoMIPS).
[ 0.180011] CPU0 attaching sched-domain:
[ 0.180011] domain 0: span 0
[ 0.180011] groups: 0
[ 0.180011] net_namespace: 660 bytes
[ 0.180011] Booting paravirtualized kernel on bare hardware
[ 0.180011] NET: Registered protocol family 16
[ 0.180011] ACPI: bus type pci registered
[ 0.264016] PCI: PCI BIOS revision 2.10 entry at 0xfd958, last bus=2
[ 0.264016] PCI: Using configuration type 1 for base access
[ 0.264016] Setting up standard PCI resources
[ 0.268801] ACPI: EC: Look up EC in DSDT
[ 0.273414] ACPI: Interpreter enabled
[ 0.273422] ACPI: (supports S0 S3 S4 S5)
[ 0.273448] ACPI: Using IOAPIC for interrupt routing
[ 0.317701] ACPI: EC: GPE = 0x6, I/O: command/status = 0x66, data = 0x62
[ 0.317707] ACPI: EC: driver started in poll mode
[ 0.317791] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.318710] PCI: Transparent bridge - 0000:00:14.4
[ 0.318758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.318986] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.319233] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 0.322585] ACPI: PCI Interrupt Link [LNK0] (IRQs 10 11) *0, disabled.
[ 0.322777] ACPI: PCI Interrupt Link [LNK1] (IRQs 10 11) *0, disabled.
[ 0.322965] ACPI: PCI Interrupt Link [LNK2] (IRQs 10 11) *0, disabled.
[ 0.323151] ACPI: PCI Interrupt Link [LNK3] (IRQs 10 11) *0, disabled.
[ 0.323574] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.323635] pnp: PnP ACPI init
[ 0.323651] ACPI: bus type pnp registered
[ 0.348208] pnp: PnP ACPI: found 9 devices
[ 0.348215] ACPI: ACPI bus type pnp unregistered
[ 0.348221] PnPBIOS: Disabled by ACPI PNP
[ 0.348725] PCI: Using ACPI for IRQ routing
[ 0.349008] ACPI: RTC can wake from S4
[ 0.349065] system 00:07: ioport range 0x1080-0x1080 has been reserved
[ 0.349071] system 00:07: ioport range 0x200-0x20f has been reserved
[ 0.349076] system 00:07: ioport range 0x220-0x22f has been reserved
[ 0.349080] system 00:07: ioport range 0x40b-0x40b has been reserved
[ 0.349085] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.349089] system 00:07: ioport range 0x4d6-0x4d6 has been reserved
[ 0.349094] system 00:07: ioport range 0x530-0x537 has been reserved
[ 0.349099] system 00:07: ioport range 0xc00-0xc01 has been reserved
[ 0.349103] system 00:07: ioport range 0xc14-0xc14 has been reserved
[ 0.349111] system 00:07: ioport range 0xc50-0xc52 has been reserved
[ 0.349115] system 00:07: ioport range 0xc6c-0xc6c has been reserved
[ 0.349120] system 00:07: ioport range 0xc6f-0xc6f has been reserved
[ 0.349125] system 00:07: ioport range 0xcd6-0xcd7 has been reserved
[ 0.349130] system 00:07: ioport range 0x8000-0x805f has been reserved
[ 0.349135] system 00:07: ioport range 0xfe00-0xfe00 has been reserved
[ 0.349140] system 00:07: ioport range 0xfe10-0xfe11 has been reserved
[ 0.349153] system 00:08: iomem range 0x0-0x9ffff could not be reserved
[ 0.349159] system 00:08: iomem range 0xe0000-0xfffff could not be reserved
[ 0.349164] system 00:08: iomem range 0x100000-0x1bffffff could not be reserved
[ 0.349170] system 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.349175] system 00:08: iomem range 0xe8000000-0xe8000fff has been reserved
[ 0.379898] PCI: region 0000:02:04.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.379911] PCI: Bridge: 0000:00:01.0
[ 0.379916] IO window: 9000-9fff
[ 0.379922] MEM window: 0xe8100000-0xe81fffff
[ 0.379928] PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff
[ 0.379942] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[ 0.379945] IO window: 0x0000a400-0x0000a4ff
[ 0.379952] IO window: 0x0000a800-0x0000a8ff
[ 0.379958] MEM window: 0x30000000-0x33ffffff
[ 0.379964] PCI: Bridge: 0000:00:14.4
[ 0.379968] IO window: a000-afff
[ 0.379974] MEM window: 0xe8200000-0xe82fffff
[ 0.379978] PREFETCH window: disabled.
[ 0.380034] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.380084] NET: Registered protocol family 2
[ 0.380266] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.380621] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.380751] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.380877] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.380883] TCP reno registered
[ 0.381013] NET: Registered protocol family 1
[ 0.381222] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 0.899701] it is
[ 1.483804] Freeing initrd memory: 7356k freed
[ 1.485005] audit: initializing netlink socket (disabled)
[ 1.485035] type=2000 audit(1245532913.484:1): initialized
[ 1.485237] Total HugeTLB memory allocated, 0
[ 1.485355] VFS: Disk quotas dquot_6.5.1
[ 1.485403] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.485467] msgmni has been set to 879
[ 1.485655] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.485662] io scheduler noop registered
[ 1.485665] io scheduler anticipatory registered
[ 1.485669] io scheduler deadline registered
[ 1.485689] io scheduler cfq registered (default)
[ 2.014435] pci 0000:01:05.0: Boot video device
[ 2.015045] isapnp: Scanning for PnP cards...
[ 2.366284] isapnp: No Plug & Play device found
[ 2.370961] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.371673] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.371684] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[ 2.374223] brd: module loaded
[ 2.374397] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 2.387438] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.395042] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.395051] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.395056] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.395063] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.395067] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.395359] mice: PS/2 mouse device common for all mice
[ 2.395850] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.395870] rtc0: alarms up to one day
[ 2.395933] cpuidle: using governor ladder
[ 2.395938] cpuidle: using governor menu
[ 2.395947] No iBFT detected.
[ 2.396730] TCP cubic registered
[ 2.396736] NET: Registered protocol family 17
[ 2.396748] Using IPI No-Shortcut mode
[ 2.396766] registered taskstats version 1
[ 2.396766] rtc_cmos 00:03: setting system clock to 2009-06-20 21:21:55 UTC (1245532915)
[ 2.396766] Freeing unused kernel memory: 244k freed
[ 2.430996] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.593975] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 2.594065] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.594073] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 3.214114] usbcore: registered new interface driver usbfs
[ 3.214169] usbcore: registered new interface driver hub
[ 3.214230] usbcore: registered new device driver usb
[ 3.222394] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.222440] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.222465] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 3.222661] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 3.222697] ohci_hcd 0000:00:13.0: irq 19, io mem 0xe8001000
[ 3.226873] Linux agpgart interface v0.103
[ 3.280190] usb usb1: configuration #1 chosen from 1 choice
[ 3.280248] hub 1-0:1.0: USB hub found
[ 3.280268] hub 1-0:1.0: 3 ports detected
[ 3.384257] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.384265] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.384271] usb usb1: Product: OHCI Host Controller
[ 3.384275] usb usb1: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 3.384279] usb usb1: SerialNumber: 0000:00:13.0
[ 3.384327] agpgart: Detected Ati IGP9100/M chipset
[ 3.387614] agpgart: AGP aperture is 32M @ 0xea000000
[ 3.387665] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.387683] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 3.387727] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 3.387764] ohci_hcd 0000:00:13.1: irq 19, io mem 0xe8002000
[ 3.444187] usb usb2: configuration #1 chosen from 1 choice
[ 3.444249] hub 2-0:1.0: USB hub found
[ 3.444265] hub 2-0:1.0: 3 ports detected
[ 3.548240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.548248] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.548253] usb usb2: Product: OHCI Host Controller
[ 3.548256] usb usb2: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 3.548260] usb usb2: SerialNumber: 0000:00:13.1
[ 3.548416] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.548447] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 3.548494] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 3.548552] ehci_hcd 0000:00:13.2: irq 19, io mem 0xe8003000
[ 3.688050] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 3.700070] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.700228] usb usb3: configuration #1 chosen from 1 choice
[ 3.700283] hub 3-0:1.0: USB hub found
[ 3.700302] hub 3-0:1.0: 6 ports detected
[ 3.756061] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 3.791972] No dock devices found.
[ 3.806424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.806432] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.806437] usb usb3: Product: EHCI Host Controller
[ 3.806441] usb usb3: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 3.806445] usb usb3: SerialNumber: 0000:00:13.2
[ 3.880552] SCSI subsystem initialized
[ 3.991611] libata version 3.00 loaded.
[ 4.076903] Uniform Multi-Platform E-IDE driver
[ 4.076914] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.089232] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.139116] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[e8204000-e82047ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 4.143148] 8139too Fast Ethernet driver 0.9.28
[ 4.253009] ATIIXP: IDE controller (0x1002:0x4349 rev 0x00) at PCI slot 0000:00:14.1
[ 4.253026] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.253043] ATIIXP: not 100% native mode: will probe irqs later
[ 4.253057] ide0: BM-DMA at 0x8070-0x8077
[ 4.253068] ide1: BM-DMA at 0x8078-0x807f
[ 4.253076] Probing IDE interface ide0...
[ 4.262179] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 4.263125] eth0: RealTek RTL8139 at 0xa000, 00:02:3f:d2:04:bf, IRQ 19
[ 4.263130] eth0: Identified 8139 chip type 'RTL-8101'
[ 4.268452] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 4.468061] usb 3-3: new high speed USB device using ehci_hcd and address 3
[ 4.539578] Marking TSC unstable due to: TSC halts in idle.
[ 4.540241] hda: SAMSUNG HM160HC, ATA DISK drive
[ 4.733091] usb 3-3: configuration #1 chosen from 1 choice
[ 4.733091] usb 3-3: New USB device found, idVendor=067b, idProduct=3507
[ 4.733091] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.733091] usb 3-3: Product: ATAPI-6 Bridge Controller
[ 4.733091] usb 3-3: Manufacturer: Prolific Technology Inc.
[ 4.733091] usb 3-3: SerialNumber: 261E
[ 4.776586] Initializing USB Mass Storage driver...
[ 5.036032] usb 1-2: new low speed USB device using ohci_hcd and address 3
[ 5.212114] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.212195] hda: UDMA/100 mode selected
[ 5.212271] Probing IDE interface ide1...
[ 5.250590] usb 1-2: configuration #1 chosen from 1 choice
[ 5.252920] usb 1-2: New USB device found, idVendor=04d9, idProduct=1133
[ 5.252928] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.253150] scsi0 : SCSI emulation for USB Mass Storage devices
[ 5.253331] usbcore: registered new interface driver usb-storage
[ 5.253338] USB Mass Storage support registered.
[ 5.257409] usb-storage: device found at 3
[ 5.257415] usb-storage: waiting for device to settle before scanning
[ 5.330566] usbcore: registered new interface driver hiddev
[ 5.342584] input: HID 04d9:1133 as /class/input/input1
[ 5.342584] input,hidraw0: USB HID v1.10 Mouse [HID 04d9:1133] on usb-0000:00:13.0-2
[ 5.342584] usbcore: registered new interface driver usbhid
[ 5.342584] usbhid: v2.6:USB HID core driver
[ 5.524242] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f414b001588]
[ 5.780126] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.798226] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.845589] hda: max request size: 512KiB
[ 5.847618] hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
[ 5.849344] hda: cache flushes supported
[ 5.849344] hda: hda1 hda2 hda3
[ 6.161455] device-mapper: uevent: version 1.0.3
[ 6.163553] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 6.433971] PM: Starting manual resume from disk
[ 6.487230] kjournald starting. Commit interval 5 seconds
[ 6.487230] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.111065] udevd version 125 started
[ 10.256259] usb-storage: device scan complete
[ 10.257971] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H44N RB01 PQ: 0 ANSI: 0
[ 10.440036] Driver 'sr' needs updating - please use bus_type methods
[ 10.444970] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[ 10.444981] Uniform CD-ROM driver Revision: 3.20
[ 10.445157] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 10.518700] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 86.717024] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 86.736128] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 87.055158] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 87.840056] input: Power Button (FF) as /class/input/input2
[ 87.869253] ACPI: Power Button (FF) [PWRF]
[ 87.869375] input: Lid Switch as /class/input/input3
[ 87.882347] ACPI: Lid Switch [LID]
[ 87.882476] input: Power Button (CM) as /class/input/input4
[ 87.909746] ACPI: Power Button (CM) [PWRB]
[ 87.950103] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 87.972854] ACPI: AC Adapter [ACAD] (on-line)
[ 88.696327] ACPI: Battery Slot [BAT1] (battery present)
[ 88.990017] input: Video Bus as /class/input/input5
[ 89.018539] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 89.266752] input: PC Speaker as /class/input/input6
[ 89.956706] Yenta: CardBus bridge found at 0000:02:04.0 [1179:ff00]
[ 89.956734] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[ 89.956739] IO window: 0x0000a400-0x0000a4ff
[ 89.956745] IO window: 0x0000a800-0x0000a8ff
[ 89.956752] PREFETCH window: 0x34000000-0x343fffff
[ 89.956759] MEM window: 0x30000000-0x33ffffff
[ 89.956771] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 89.956774] Yenta: Routing CardBus interrupts to PCI
[ 89.956782] Yenta TI: socket 0000:02:04.0, mfunc 0x00111c12, devctl 0x44
[ 90.066214] input: PS/2 Mouse as /class/input/input7
[ 90.112762] input: AlpsPS/2 ALPS GlidePoint as /class/input/input8
[ 90.188908] Yenta: ISA IRQ mask 0x0eb0, PCI irq 16
[ 90.188916] Socket status: 30000006
[ 90.188923] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 90.188928] cs: IO port probe 0xa000-0xafff: clean.
[ 90.189328] pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
[ 90.529228] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 90.530276] atiixp: codec reset timeout
[ 90.702196] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
[ 90.708608] atiixp-modem: no codec available
[ 90.708704] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[ 91.328018] cs: IO port probe 0x100-0x3af: clean.
[ 91.328018] cs: IO port probe 0x3e0-0x4ff: clean.
[ 91.328018] cs: IO port probe 0x820-0x8ff: clean.
[ 91.328018] cs: IO port probe 0xc00-0xcf7: clean.
[ 91.328018] cs: IO port probe 0xa00-0xaff: clean.
[ 92.446723] EXT3 FS on dm-1, internal journal
[ 92.780663] loop: module loaded
[ 94.288329] kjournald starting. Commit interval 5 seconds
[ 94.288488] EXT3 FS on dm-3, internal journal
[ 94.288488] EXT3-fs: mounted filesystem with ordered data mode.
[ 94.355482] Adding 2928632k swap on /dev/mapper/messenger_main-swap. Priority:-1 extents:1 across:2928632k
[ 95.645872] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 98.461501] NET: Registered protocol family 10
[ 98.462214] lo: Disabled Privacy Extensions
[ 98.876032] Clocksource tsc unstable (delta = 142080646 ns)
[ 100.282024] lp: driver loaded but no devices found
[ 100.335157] ppdev: user-space parallel port driver
[ 103.385503] Bluetooth: Core ver 2.11
[ 103.388116] NET: Registered protocol family 31
[ 103.388126] Bluetooth: HCI device and connection manager initialized
[ 103.388133] Bluetooth: HCI socket layer initialized
[ 103.458001] Bluetooth: L2CAP ver 2.9
[ 103.458011] Bluetooth: L2CAP socket layer initialized
[ 103.464877] Bluetooth: RFCOMM socket layer initialized
[ 103.464898] Bluetooth: RFCOMM TTY layer initialized
[ 103.464902] Bluetooth: RFCOMM ver 1.8
[ 106.205323] [drm] Initialized drm 1.1.0 20060810
[ 106.213576] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 106.213852] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 107.419890] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 107.419890] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 107.419890] agpgart: Putting AGP V3 device at 0000:01:05.0 into 8x mode
[ 108.657725] [drm] Setting GART location based on new memory map
[ 108.657725] [drm] Loading R200 Microcode
[ 108.657725] [drm] writeback test succeeded in 1 usecs
[ 108.860026] eth0: no IPv6 routers present
Reply to: