Ответ: Установка сканнера

[Джеймс Браун <jbrownfirst@gmail.com>]

Вроде все распознает теперь:
# dmesg | tail
[   53.819036] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[   53.819854] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[   53.819891] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[   53.819954] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[   66.148096] usb 1-1: new full speed USB device using uhci_hcd and address 2
[   66.321230] usb 1-1: configuration #1 chosen from 1 choice
[   66.327265] usb 1-1: New USB device found, idVendor=04a9, idProduct=220d
[   66.327290] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   66.327297] usb 1-1: Product: CanoScan
[   66.327301] usb 1-1: Manufacturer: Canon

# scanimage -d test -T
scanimage: scanning image of size 157x196 pixels at 8 bits/pixel
scanimage: acquiring gray frame, 8 bits/sample
scanimage: reading one scanline, 157 bytes...	PASS
scanimage: reading one byte...		PASS
scanimage: stepped read, 2 bytes... 	PASS
scanimage: stepped read, 4 bytes... 	PASS
scanimage: stepped read, 8 bytes... 	PASS
scanimage: stepped read, 16 bytes... 	PASS
scanimage: stepped read, 32 bytes... 	PASS
scanimage: stepped read, 64 bytes... 	PASS
scanimage: stepped read, 128 bytes... 	PASS
scanimage: stepped read, 256 bytes... 	PASS
scanimage: stepped read, 255 bytes... 	PASS
scanimage: stepped read, 127 bytes... 	PASS
scanimage: stepped read, 63 bytes... 	PASS
scanimage: stepped read, 31 bytes... 	PASS
scanimage: stepped read, 15 bytes... 	PASS
scanimage: stepped read, 7 bytes... 	PASS
scanimage: stepped read, 3 bytes... 	PASS

sane-find-scanner

  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.
  # Also you need support for SCSI Generic (sg) in your operating system.
  # If using Linux, try "modprobe sg".

found USB scanner (vendor=0x04a9 [Canon], product=0x220d [CanoScan],
chip=LM9832/3) at libusb:001:002
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.


# scanimage -L
device `plustek:libusb:001:003' is a Canon CanoScan N670U/N676U/LiDE20
flatbed scanner


Но сканнер физически ни хрена не работает!!!

01.03.09, Тихон Тарнавский<tikhon@lexpr.ru> написал(а):
> On Sat, 28.02.2009 23:38:04 , Иван Лох wrote:
>> Если Вы не расковыряли себе Apt::Install-Recommends,
>> то этого _достаточно_ для запуска sane-find-scanner.
> Недостаточно чётко сформулировал: этого _может быть_
> недостаточно. Прошу прощения, не понял сразу, что имелось ввиду под
> умлочанием.
>
> --
> С уважением,
> Тихон Тарнавский.
> http://linuxforum.ru
> http://posix.ru
>
>
> --
> To UNSUBSCRIBE, email to debian-russian-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact
> listmaster@lists.debian.org
>
>