Re: smartmontools: Offline uncorrectable sectors
В Срд, 05/12/2007 в 18:40 +0200, Maxim Kudelya пишет:
> Покотиленко Костик wrote:
> > sda - загрузочный
> > sdb-sde - mdadm RAID 10
> >
> > Что это значит? Битые секторы или что?
> Прогоните тесты для начала:
> Для SATA винтов:
> smartctl -d ata -t short /dev/sdb
> smartctl -d ata -t long /dev/sdb
>
> И покажите потом:
> smartctl -d ata -a /dev/sdb
Из 4-х дисков, 2 не прошли тест, на 2-х тест прерывается, проверю позже
без нагрузки.
Кстати, для RAID 10 от mdadm нужно SMART на отдельные винты включать или
на массив, как в случае с 3ware?
По этому можно что-то сказать?
# smartctl -a -d ata /dev/sdb
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200YS-01PGB0
Serial Number: WD-WCAPD4751993
Firmware Version: 21.00M21
User Capacity: 320.072.933.376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Dec 6 13:42:03 2007 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 111) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 191 190 021 Pre-fail Always - 5433
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 37
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2224
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 36
190 Unknown_Attribute 0x0022 075 046 000 Old_age Always - 25
194 Temperature_Celsius 0x0022 125 096 000 Old_age Always - 25
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 2
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 2
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 48 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 48 occurred at disk power-on lifetime: 2116 hours (88 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 80 0c cc e0 Error: AMNF at LBA = 0x00cc0c80 = 13372544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 80 0c cc 17 00 9d+21:59:57.286 READ DMA EXT
ec 03 45 00 00 00 00 00 9d+21:59:57.285 IDENTIFY DEVICE
ef 03 45 00 00 00 00 00 9d+21:59:57.285 SET FEATURES [Set transfer mode]
ec 00 01 01 00 00 00 00 9d+21:59:57.283 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:55.187 READ DMA EXT
Error 47 occurred at disk power-on lifetime: 2116 hours (88 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 80 0c cc e0 Error: AMNF at LBA = 0x00cc0c80 = 13372544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 80 0c cc 17 00 9d+21:59:55.187 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:55.186 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:53.249 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:53.248 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:51.310 READ DMA EXT
Error 46 occurred at disk power-on lifetime: 2116 hours (88 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 80 0c cc e0 Error: AMNF at LBA = 0x00cc0c80 = 13372544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 80 0c cc 17 00 9d+21:59:53.249 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:53.248 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:51.310 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:51.309 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:49.372 READ DMA EXT
Error 45 occurred at disk power-on lifetime: 2116 hours (88 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 80 0c cc e0 Error: AMNF at LBA = 0x00cc0c80 = 13372544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 80 0c cc 17 00 9d+21:59:51.310 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:51.309 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:49.372 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:49.371 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:47.439 READ DMA EXT
Error 44 occurred at disk power-on lifetime: 2116 hours (88 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 80 0c cc e0 Error: AMNF at LBA = 0x00cc0c80 = 13372544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 80 0c cc 17 00 9d+21:59:49.372 READ DMA EXT
ec 00 00 81 0f cc 00 00 9d+21:59:49.371 IDENTIFY DEVICE
25 00 00 80 0c cc 17 00 9d+21:59:47.439 READ DMA EXT
25 00 80 00 0c cc 17 00 9d+21:59:47.424 READ DMA EXT
ec 00 00 f1 0b cc 00 00 9d+21:59:47.423 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 2223 399248369
# 2 Short offline Completed: read failure 90% 2223 399248369
# 3 Short offline Completed: read failure 90% 2223 399248369
# 4 Short offline Completed: read failure 90% 2223 399248369
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
#
--
Покотиленко Костик <casper@meteor.dp.ua>
Reply to: