Re: Sarge/beta-3 on a RS6000/43P-150 (PPC 604e, CHRP)?
Hi Sven,
I'm sending you the boot info and the output of
/proc/pci.
The network card driver I need is:
Ethernet controller: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE]
Best regards,
Daniel
boot cdrom:\vmlinuz devfs=mount console=ttyS0
chrpboot starting: loaded at 0
x00400000
initial ramdisk moving 0x3e89000 <- 0x005a2000 (176836
bytes)
gunzipping (0x00010000 <-
0x00406c64:0x005a14fe)...done 3641172 bytes
49624 bytes of heap consumed, max in use 1651774704
start address = 0x10000
instantiating rtas at 00600000 ... done
opening display /pci@fee00000/display@c... ok
copying OF device tree...done
starting cpu /cpus/PowerPC,604@1...ok
starting cpu /cpus/PowerPC,604@2...ok
starting cpu /cpus/PowerPC,604@3...ok
Calling quiesce ...
returning 0x00010000 from prom_init
Memory BAT mapping: BAT2=256Mb, BAT3=256Mb, residual:
1536Mb
Warning, memory limited to 768 Mb, use CONFIG_HIGHMEM
to reach 2048 Mb
Total memory = 768MB; using 2048kB for hash table (at
c0400000)
Linux version 2.4.25-powerpc (root@pegasos2) (version
gcc 3.3.3 (Debian)) #1 jeu
mar 4 13:53:12 CET 2004
PCI bus 0 controlled by pci at fef00000
hose pci, pci_mem_offset: a0000000, start0: a1000000
io_base_virt: fcffe000, io_base_phys: 88000000,
isa_mem_base: a0000000
pci_dram_offset = 80000000
PCI bus 64 controlled by pci at fee00000
hose pci, pci_mem_offset: a0000000, start0: c0000000
io_base_virt: fbffc000, io_base_phys: 90000000,
isa_mem_base: a0000000
PCI bus 128 controlled by pci at fed00000
hose pci, pci_mem_offset: a0000000, start0: e0000000
io_base_virt: faffa000, io_base_phys: 98000000,
isa_mem_base: a0000000
RTAS Event Scan Rate: 1 calls/minute (every 6000
jiffies)
On node 0 totalpages: 196608
zone(0): 196608 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: devfs=mount console=ttyS0
OpenPIC at bf5c0000 (size 40000)
OpenPIC irqs 0..15 in IDU
OpenPIC Version 1.0 (4 CPUs and 16 IRQ sources) at
fafba000
OpenPIC timer frequency is 4.166666 MHz
time_init: decrementer frequency = 41.500475 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 331.77 BogoMIPS
Memory: 769476k available (2328k kernel code, 1404k
data, 208k init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8,
1048576 bytes)
Inode cache hash table entries: 65536 (order: 7,
524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096
bytes)
Buffer cache hash table entries: 65536 (order: 6,
262144 bytes)
Page-cache hash table entries: 262144 (order: 8,
1048576 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Scanning bus 00
Found 00:00 [1014/002d] 000600 00
Found 00:58 [1014/000a] 000601 00
Found 00:60 [1000/0003] 000100 00
Fixup res 1 (200) of dev 00:0c.0: 1f57e000 -> bf57e000
Fixup res 2 (200) of dev 00:0c.0: 1f57f000 -> bf57f000
Found 00:68 [1023/2000] 000200 00
Fixup res 1 (200) of dev 00:0d.0: 1f57c000 -> bf57c000
Fixup res 6 (7200) of dev 00:0d.0: 1f600000 ->
bf600000
Found 00:70 [1014/0058] 000c02 00
Fixup res 1 (1208) of dev 00:0e.0: 1f800000 ->
bf800000
Fixup res 2 (1208) of dev 00:0e.0: 1f580000 ->
bf580000
Fixup res 3 (1208) of dev 00:0e.0: 1f5a0000 ->
bf5a0000
Fixup res 4 (1208) of dev 00:0e.0: 1f700000 ->
bf700000
Fixup res 6 (7200) of dev 00:0e.0: 1f588000 ->
bf588000
Found 00:80 [1022/2000] 000200 00
Fixup res 1 (200) of dev 00:10.0: 1f57d000 -> bf57d000
Fixup res 6 (7200) of dev 00:10.0: 1f590000 ->
bf590000
Found 00:88 [1014/0046] 00ff00 00
Fixup res 0 (200) of dev 00:11.0: 1f5c0000 -> bf5c0000
Fixups for bus 00
Bus scan for 00 returning with max=00
Scanning bus 40
Found 40:00 [1014/002d] 000600 00
Found 40:58 [12ae/0001] 000200 00
Fixup res 0 (200) of dev 40:0b.0: 3cfec000 -> dcfec000
Found 40:60 [102b/0520] 000300 00
Fixup res 0 (1208) of dev 40:0c.0: 3e000000 ->
de000000
Fixup res 1 (200) of dev 40:0c.0: 3d000000 -> dd000000
Fixup res 2 (200) of dev 40:0c.0: 3d800000 -> dd800000
Fixup res 6 (7200) of dev 40:0c.0: 3cff0000 ->
dcff0000
Fixups for bus 40
Bus scan for 40 returning with max=40
Scanning bus 80
Found 80:00 [1014/002d] 000600 00
Found 80:58 [1000/0003] 000100 00
Fixup res 0 (101) of dev 80:0b.0: 7fffc00 -> 5ffbc00
Fixup res 1 (200) of dev 80:0b.0: 4fffe000 -> efffe000
Fixup res 2 (200) of dev 80:0b.0: 4ffff000 -> effff000
Fixups for bus 80
Bus scan for 80 returning with max=80
PCI: bridge rsrc 0..ffffff (100), parent c02ca1d8
PCI: bridge rsrc a1000000..bfffffff (200), parent
c02ca1f4
PCI: bridge rsrc a0000000..a0ffffff (200), parent
c02ca1f4
PCI: bridge rsrc feffe000..ffffdfff (100), parent
c02ca1d8
PCI: bridge rsrc c0000000..dfffffff (200), parent
c02ca1f4
PCI: bridge rsrc fdffc000..feffbfff (100), parent
c02ca1d8
PCI: bridge rsrc e0000000..efffffff (200), parent
c02ca1f4
PCI:00:0b.0: Resource 0: 07ffec00-07ffec07 (f=101),
vd: 1014, dev: 000a
PCI: Cannot allocate resource region 0 of device
00:0b.0
PCI:00:11.0: Resource 0: bf5c0000-bf5fffff (f=200),
vd: 1014, dev: 0046
PCI:40:0c.0: Resource 0: de000000-deffffff (f=1208),
vd: 102b, dev: 0520
PCI:40:0c.0: Resource 1: dd000000-dd003fff (f=200),
vd: 102b, dev: 0520
PCI:40:0c.0: Resource 2: dd800000-ddffffff (f=200),
vd: 102b, dev: 0520
PCI:00:0c.0: Resource 0: 07fff800-07fff8ff (f=101),
vd: 1000, dev: 0003
PCI: Cannot allocate resource region 0 of device
00:0c.0
PCI:00:0c.0: Resource 1: bf57e000-bf57e0ff (f=200),
vd: 1000, dev: 0003
PCI:00:0c.0: Resource 2: bf57f000-bf57ffff (f=200),
vd: 1000, dev: 0003
PCI:00:0d.0: Resource 0: 07fff000-07fff01f (f=101),
vd: 1022, dev: 2000
PCI: Cannot allocate resource region 0 of device
00:0d.0
PCI:00:0d.0: Resource 1: bf57c000-bf57c01f (f=200),
vd: 1022, dev: 2000
PCI:00:0e.0: Resource 0: 07fffc00-07fffcff (f=101),
vd: 1014, dev: 0058
PCI: Cannot allocate resource region 0 of device
00:0e.0
PCI:00:0e.0: Resource 1: bf800000-bfffffff (f=1208),
vd: 1014, dev: 0058
PCI:00:0e.0: Resource 2: bf580000-bf587fff (f=1208),
vd: 1014, dev: 0058
PCI:00:0e.0: Resource 3: bf5a0000-bf5bffff (f=1208),
vd: 1014, dev: 0058
PCI:00:0e.0: Resource 4: bf700000-bf7fffff (f=1208),
vd: 1014, dev: 0058
PCI:00:10.0: Resource 0: 07fff400-07fff41f (f=101),
vd: 1022, dev: 2000
PCI: Cannot allocate resource region 0 of device
00:10.0
PCI:00:10.0: Resource 1: bf57d000-bf57d01f (f=200),
vd: 1022, dev: 2000
PCI:40:0b.0: Resource 0: dcfec000-dcfeffff (f=200),
vd: 12ae, dev: 0001
PCI:80:0b.0: Resource 0: 05ffbc00-05ffbcff (f=101),
vd: 1000, dev: 0003
PCI: Cannot allocate resource region 0 of device
80:0b.0
PCI:80:0b.0: Resource 1: efffe000-efffe0ff (f=200),
vd: 1000, dev: 0003
PCI:80:0b.0: Resource 2: effff000-efffffff (f=200),
vd: 1000, dev: 0003
PCI: moved device 00:0b.0 resource 0 (101) to 1000
PCI: moved device 00:0c.0 resource 0 (101) to 1400
PCI: moved device 00:0d.0 resource 0 (101) to 1020
PCI: moved device 00:0e.0 resource 0 (101) to 1800
PCI: moved device 00:10.0 resource 0 (101) to 1040
PCI: moved device 80:0b.0 resource 0 (101) to 0
Don't know how to access NVRAM with 4 addresses
nvram: OF partition at 0x1800
nvram: XP partition at 0x1300
nvram: NR partition at 0x1400
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society
NET3.039
Initializing RT netlink socket
Thermal assist unit not available
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch
(rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
matroxfb: Matrox MGA-G200 (PCI) detected
matroxfb: BIOS on your Matrox device does not contain
powerup info
matroxfb: 640x480x8bpp (virtual: 640x3270)
matroxfb: framebuffer at 0xDE000000, mapped to
0xf1012000, size 2097152
Console: switching to colour frame buffer device 80x30
fb0: MATROX VGA frame buffer device
initialize_kbd: Keyboard reset failed, no ACK
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Serial driver version 5.05c (2001-07-08) with
MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Generic RTC Driver v1.07
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro
Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 8192K size
1024 blocksize
Uniform Multi-Platform E-IDE driver Revision:
7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
SCSI subsystem driver Revision: 1.00
PCI: Enabling device 00:0c.0 (0140 -> 0143)
sym.0.12.0: setting PCI_COMMAND_MASTER...
sym.0.12.0: setting PCI_COMMAND_INVALIDATE.
PCI: Enabling device 80:0b.0 (0140 -> 0143)
sym.128.11.0: setting PCI_COMMAND_MASTER...
sym.128.11.0: setting PCI_COMMAND_INVALIDATE.
sym0: <825a> rev 0x14 on pci bus 0 device 12 function
0 irq 17
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
sym1: <825a> rev 0x14 on pci bus 128 device 11
function 0 irq 26
sym1: No NVRAM, ID 7, Fast-10, SE, parity checking
sym1: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
scsi1 : sym-2.1.17a
blk: queue c0fb1414, I/O limit 4095Mb (mask
0xffffffff)
Vendor: IBM Model: CDRM00203 !K Rev: 1_01
Type: CD-ROM ANSI SCSI
revision: 02
blk: queue c0fb1e14, I/O limit 4095Mb (mask
0xffffffff)
sym0:5: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
Vendor: ARCHIVE Model: IBM-STD224000N!D Rev: 758B
Type: Sequential-Access ANSI SCSI
revision: 02
blk: queue efde7214, I/O limit 4095Mb (mask
0xffffffff)
sym0:6: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efde7614, I/O limit 4095Mb (mask
0xffffffff)
sym0:6:0: tagged command queuing enabled, command
queue depth 16.
sym1:8: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efdb2814, I/O limit 4095Mb (mask
0xffffffff)
sym1:9: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efdb2c14, I/O limit 4095Mb (mask
0xffffffff)
sym1:10: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efd7e014, I/O limit 4095Mb (mask
0xffffffff)
sym1:11: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efd7e414, I/O limit 4095Mb (mask
0xffffffff)
sym1:12: FAST-10 WIDE SCSI 20.0 MB/s ST (100.0 ns,
offset 8)
Vendor: IBM Model: DNES-309170W Rev: SAG0
Type: Direct-Access ANSI SCSI
revision: 03
blk: queue efd7e814, I/O limit 4095Mb (mask
0xffffffff)
Vendor: IBMAUSTN Model: HSBP06UUSYSTEM Rev: 0218
Type: Enclosure ANSI SCSI
revision: 03
blk: queue efd30014, I/O limit 4095Mb (mask
0xffffffff)
sym1:8:0: tagged command queuing enabled, command
queue depth 16.
sym1:9:0: tagged command queuing enabled, command
queue depth 16.
sym1:10:0: tagged command queuing enabled, command
queue depth 16.
sym1:11:0: tagged command queuing enabled, command
queue depth 16.
sym1:12:0: tagged command queuing enabled, command
queue depth 16.
mesh: configured for synchronous 5 MB/s
Attached scsi disk sda at scsi0, channel 0, id 6, lun
0
Attached scsi disk sdb at scsi1, channel 0, id 8, lun
0
Attached scsi disk sdc at scsi1, channel 0, id 9, lun
0
Attached scsi disk sdd at scsi1, channel 0, id 10, lun
0
Attached scsi disk sde at scsi1, channel 0, id 11, lun
0
Attached scsi disk sdf at scsi1, channel 0, id 12, lun
0
SCSI device sda: 17774160 512-byte hdwr sectors (9100
MB)
Partition check:
/dev/scsi/host0/bus0/target6/lun0: p1 p2
sdb: Spinning up disk............ready
SCSI device sdb: 17774160 512-byte hdwr sectors (9100
MB)
/dev/scsi/host1/bus0/target8/lun0: p2 p3 p4
sdc: Spinning up disk..............ready
SCSI device sdc: 17774160 512-byte hdwr sectors (9100
MB)
/dev/scsi/host1/bus0/target9/lun0: unknown partition
table
sdd: Spinning up disk.............ready
SCSI device sdd: 17774160 512-byte hdwr sectors (9100
MB)
/dev/scsi/host1/bus0/target10/lun0: unknown partition
table
sde: Spinning up disk..............ready
SCSI device sde: 17774160 512-byte hdwr sectors (9100
MB)
/dev/scsi/host1/bus0/target11/lun0: unknown partition
table
sdf: Spinning up disk.............ready
SCSI device sdf: 17774160 512-byte hdwr sectors (9100
MB)
/dev/scsi/host1/bus0/target12/lun0: unknown partition
table
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 4,
lun 0
sym0:4: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
sbp2: $Rev: 1074 $ Ben Collins <bcollins@debian.org>
Macintosh non-volatile memory driver v1.0
apm_emu: Requires a machine with a PMU.
Warning: no ADB interface detected
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-uhci.c: $Revision: 1.275 $ time 13:57:14 Mar
4 2004
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller
Interface driver
usb.c: registered new driver usbmouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
mice: PS/2 mouse device common for all mice
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind
65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1498k freed
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 208k init 56k pmac 36k
prep
Setting up filesystem, please wait ...
umount: /initrd: Invalid argument
insmod: usbkbd.o: no module by that name found
modprobe: failed to load module usbkbd
insmod: keybdev.o: no module by that name found
modprobe: failed to load module keybdev
Using
/lib/modules/2.4.25-powerpc/kernel/drivers/usb/serial/usbserial.o
================
# cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: IBM Python (rev 1).
Bus 0, device 11, function 0:
ISA bridge: IBM Fire Coral (rev 3).
I/O at 0x1000 [0x1007].
Bus 0, device 12, function 0:
SCSI storage controller: LSI Logic / Symbios Logic
53c825 (rev 20).
IRQ 17.
Master Capable. Latency=32. Min Gnt=17.Max
Lat=64.
I/O at 0x1400 [0x14ff].
Non-prefetchable 32 bit memory at 0xbf57e000
[0xbf57e0ff].
Non-prefetchable 32 bit memory at 0xbf57f000
[0xbf57ffff].
Bus 0, device 13, function 0:
Ethernet controller: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] (rev 38).
IRQ 19.
Master Capable. Latency=32. Min Gnt=6.Max
Lat=255.
I/O at 0x1020 [0x103f].
Non-prefetchable 32 bit memory at 0xbf57c000
[0xbf57c01f].
Bus 0, device 14, function 0:
SSA: PCI device 1014:0058 (IBM) (rev 6).
IRQ 20.
Master Capable. Latency=32.
I/O at 0x1800 [0x18ff].
Prefetchable 32 bit memory at 0xbf800000
[0xbfffffff].
Prefetchable 32 bit memory at 0xbf580000
[0xbf587fff].
Prefetchable 32 bit memory at 0xbf5a0000
[0xbf5bffff].
Prefetchable 32 bit memory at 0xbf700000
[0xbf7fffff].
Bus 0, device 16, function 0:
Ethernet controller: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] (#2) (rev 22).
IRQ 18.
Master Capable. Latency=32.
I/O at 0x1040 [0x105f].
Non-prefetchable 32 bit memory at 0xbf57d000
[0xbf57d01f].
Bus 0, device 17, function 0:
Class ff00: IBM MPIC interrupt controller (rev 0).
Non-prefetchable 32 bit memory at 0xbf5c0000
[0xbf5fffff].
Bus 64, device 0, function 0:
Host bridge: IBM Python (#2) (rev 1).
Bus 64, device 11, function 0:
Ethernet controller: Alteon Networks Inc. AceNIC
Gigabit Ethernet (rev 1).
IRQ 25.
Master Capable. Latency=32. Min Gnt=64.
Non-prefetchable 32 bit memory at 0xdcfec000
[0xdcfeffff].
Bus 64, device 12, function 0:
VGA compatible controller: Matrox Graphics, Inc.
MGA G200 (rev 1).
IRQ 23.
Master Capable. Latency=32. Min Gnt=16.Max
Lat=32.
Prefetchable 32 bit memory at 0xde000000
[0xdeffffff].
Non-prefetchable 32 bit memory at 0xdd000000
[0xdd003fff].
Non-prefetchable 32 bit memory at 0xdd800000
[0xddffffff].
Bus 128, device 0, function 0:
Host bridge: IBM Python (#3) (rev 1).
Bus 128, device 11, function 0:
SCSI storage controller: LSI Logic / Symbios Logic
53c825 (#2) (rev 20).
IRQ 26.
Master Capable. Latency=32. Min Gnt=17.Max
Lat=64.
I/O at 0xfdffc000 [0xfdffc0ff].
Non-prefetchable 32 bit memory at 0xefffe000
[0xefffe0ff].
Non-prefetchable 32 bit memory at 0xeffff000
[0xefffffff].
[snip]
--- Sven Luther <sven.luther@wanadoo.fr> wrote:
> > I'm trying the same on a 7025-f50 box.
> > Burned vmlinuz-chrp-rs6k-di-beta3-2004.03.16 on a
> > CD using ISO format - file named vmlinuz
> > 0> boot cdrom:\vmlinuz devfs=mount console=ttyS0
> >
> > I'm now stuck in loading the drivers for the
> > network card
:
> Normally the image above is self contained, if there
> are missing
> modules, we need to check why, and make sure they
> are included in the
> scsi .udeb.
>
> Friendly,
>
> Sven Luther
[snip]
__________________________________
Do you Yahoo!?
Yahoo! Mail - More reliable, more storage, less spam
http://mail.yahoo.com
Reply to: