usb ohci camera on ben8
I'm running 2.4.20-ben8 on an iBook2.2. I recently tried to use the usb port
to get at pictures on my Olympus D-100 camera.
I've installed hotplug, but can't seem to mount the camera.
When I jack the camera into the port, dmesg looks like this:
hub.c: new USB device 10:19.0-1, assigned address 4
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 88
usb-storage: Array length appears to be: 90
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc031b534 Out: 0xc031b520 Int: 0x00000000
(Period 0)
usb-storage: Found existing GUID 07b401020000000168577491
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 4
and /var/log/syslog looks like this:
Apr 10 14:12:16 debianiBookMB kernel: USB Mass Storage device found at 4
Apr 10 14:12:17 debianiBookMB /etc/hotplug/usb.agent: Setup usb-storage for
USB product 7b4/102/1065
Apr 10 14:12:17 debianiBookMB /etc/hotplug/usb.agent: missing kernel or user
mode driver usb-storage
and /proc/bus/usb/devices shows:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=db2db000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=07b4 ProdID=0102 Rev=10.65
S: Manufacturer=OLYMPUS
S: Product=C-1
S: SerialNumber=168577491
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=db2d9000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
lsmod shows that the usb-storage module has been loaded and looks good. So
what else do i have to do? Where has it mounted? Or has it?
Thanks for any light you can shed on this.
-Mark
Reply to: