scsi emulation
Still struggling with getting the scsi-emulation working in order to use
the cd-burner on my iBook2 14".
I've compiled scsi emulation into my kernel version: 2.4.20-rc1-ben0.
I've added an ide-scsi file in /etc/modutils containing the line:
alias scsi_hostadapter ide-scsi
and run update-modules. I assume because I've compiled scsi emulation
into the kernel that this isn't actually necessary.
As mentioned in a previous thread on this topic, it's likely that the
ide driver may have claimed the drive before ide-scsi. Can someone more
knowledgable then me confirm this from my kernel output. It appears to
me that this is the case. So how to I fix this?
Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual: 0Mb
Total memory = 256MB; using 512kB for hash table (at c0400000)
Linux version 2.4.20-rc1-ben0 (root@debook) (gcc version 2.95.4 20011002
(Debian prerelease)) #1 Mon Nov 4 22:18:14 EST 2002
Found Uninorth memory controller & host bridge, revision: 192
Mapped at 0xfdf3c000
Found a Pangea mac-io controller, rev: 0, mapped at 0xfdebc000
Processor NAP mode on idle enabled.
PowerMac motherboard: iBook 2 rev. 2
PMU driver 2 initialized for Core99, firmware: 0c
CPU HID1 : 0x70000044
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f1000000
io_base_virt: fd6b5000, io_base_phys: f0000000, isa_mem_base: 00000000
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f3000000
io_base_virt: fceb3000, io_base_phys: f2000000, isa_mem_base: 00000000
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f5000000
io_base_virt: fc6b1000, io_base_phys: f4000000, isa_mem_base: 00000000
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda4 ro
PowerMac using OpenPIC irq controller
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc66d000
OpenPIC timer frequency is 4.160000 MHz
GMT Delta read from XPRAM: -300 minutes, DST: off
time_init: decrementer frequency = 24.835213 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 1389.36 BogoMIPS
Memory: 254900k available (2256k kernel code, 1160k data, 176k init, 0k
highmem)
AGP special page: 0xcffff000
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Scanning bus 00
Found 00:58 [106b/0027] 000600 00
Found 00:80 [1002/4c59] 000300 00
Fixup res 1 (101) of dev 00:10.0: 400 -> 802400
Fixups for bus 00
Bus scan for 00 returning with max=00
Scanning bus 10
Found 10:58 [106b/0028] 000600 00
Found 10:b8 [106b/0025] 00ff00 00
Found 10:c0 [106b/0026] 000c03 00
Found 10:c8 [106b/0026] 000c03 00
Fixups for bus 10
Bus scan for 10 returning with max=10
Scanning bus 20
Found 20:58 [106b/0029] 000600 00
Found 20:70 [106b/0030] 000c00 00
Found 20:78 [106b/0024] 000200 00
Fixups for bus 20
Bus scan for 20 returning with max=20
PCI->OF bus map:
0 -> 0
16 -> 0
32 -> 0
PCI:00:10.0: Resource 0: 98000000-9fffffff (f=1208), vd: 1002, dev: 4c59
PCI:00:10.0: Resource 2: 90000000-9000ffff (f=200), vd: 1002, dev: 4c59
PCI:10:17.0: Resource 0: 80000000-8007ffff (f=200), vd: 106b, dev: 0025
PCI:20:0f.0: Resource 0: f5200000-f53fffff (f=200), vd: 106b, dev: 0024
PCI:00:10.0: Resource 1: 00802400-008024ff (f=101), vd: 1002, dev: 4c59
PCI:10:18.0: Resource 0: 80081000-80081fff (f=200), vd: 106b, dev: 0026
PCI:10:19.0: Resource 0: 80080000-80080fff (f=200), vd: 106b, dev: 0026
PCI:20:0e.0: Resource 0: f5000000-f5000fff (f=200), vd: 106b, dev: 0030
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-proc.o version 2.6.1 (20010825)
PCI: Enabling device 00:10.0 (0086 -> 0087)
radeonfb: ref_clk=2700, ref_div=12, xclk=16615 from OF
radeonfb: detected DFP panel size from EDID: 1024x768
Console: switching to colour frame buffer device 128x48
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon M6 LY DDR SGRAM 16 MB
radeonfb: DVI port LCD monitor connected
radeonfb: CRT port no monitor connected
no framebuffer address found for
/pci@f0000000/ATY,FallParent@10/ATY,Fall_B
input0: Macintosh mouse button emulation
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2
Probing IDE interface ide0...
hda: IBM-IC25N030ATCS04-0, ATA DISK drive
hdb: SONY CD-RW CRX800E, ATAPI CD/DVD-ROM drive
ide0 at 0xd5214000-0xd5214007,0xd5214160 on irq 19
hda: Enabling Ultra DMA 2
blk: queue c0363ba0, I/O limit 4095Mb (mask 0xffffffff)
hda: 58605120 sectors (30006 MB) w/1768KiB Cache, CHS=58140/16/63,
UDMA(33)
hdb: Enabling MultiWord DMA 2
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 8192kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.99.newide
Partition check:
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.97 3/20/02 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:88:80:c6
eth0: Found BCM5221 PHY
pcnet32.c:v1.27b 01.10.2002 tsbogend@alpha.franken.de
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 204M
agpgart: Detected Apple UniNorth/Pangea chipset
agp: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
mesh: configured for synchronous 5 MB/s
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k i2c-keywest, errno = 2
tas driver [TAS3004 driver V 0.3])
using i2c address: 0x35 from device-tree
i2c-core.o: driver TAS3004 driver V 0.3 registered.
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
PowerMac Z8530 serial driver version 2.0
tty00 at 0xd22d7020 (irq = 22) is a Z8530 ESCC
tty01 at 0xd22de000 (irq = 23) is a Z8530 ESCC
Macintosh non-volatile memory driver v1.0
Thermal Infos found :
implementation id : 3
fan_count : 1
thermostat_count : 2
ranges[0] : 0,0
ranges[1] : 0,4
ranges[2] : 192,55
ranges[3] : 243,40
thermostat: design id 3 unknown !
apm_emu: APM Emulation 0.5 initialized.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 10:18.0 (0000 -> 0002)
PCI: Enabling bus mastering for device 10:18.0
usb-ohci.c: USB OHCI at membase 0xd22e4000, IRQ 27
usb-ohci.c: usb-10:18.0, Apple Computer Inc. KeyLargo/Pangea USB
adb: starting probe task...
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 10:19.0 (0000 -> 0002)
PCI: Enabling bus mastering for device 10:19.0
usb-ohci.c: USB OHCI at membase 0xd22e6000, IRQ 28
usb-ohci.c: usb-10:19.0, Apple Computer Inc. KeyLargo/Pangea USB (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
i2c-dev.o: Registered 'uni-n 0' as minor 0
i2c-core.o: adapter uni-n 0 registered as adapter 0.
i2c-dev.o: Registered 'uni-n 1' as minor 1
i2c-core.o: adapter uni-n 1 registered as adapter 1.
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
i2c-dev.o: Registered 'mac-io 0' as minor 2
i2c-core.o: client [tas Digital Equalizer] registered to adapter [mac-io
0](pos. 0).
i2c-core.o: adapter mac-io 0 registered as adapter 2.
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
adb devices:<6>kjournald starting. Commit interval 5 seconds
[2]: 2 c3<6>EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k init 8k chrp 8k prep
[3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ANSI.
input1: ADB HID on ID 2:2.c3
input2: ADB HID on ID 7:7.1f
ADB mouse at 3, handler set to 4 (trackpad)
input3: ADB HID on ID 3:3.01
adb: finished probe task...
Adding Swap: 262136k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal
hermes.c: 5 Apr 2002 David Gibson <hermes@gibson.dropbear.id.au>
orinoco.c 0.11b (David Gibson <hermes@gibson.dropbear.id.au> and others)
airport.c 0.11b (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
eth1: Station identity 001f:0001:0008:000c
eth1: Looks like a Lucent/Agere firmware version 8.12
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:30:65:17:A8:17
eth1: Station name "HERMES I"
eth1: ready
airport: card registered for interface eth1
Reply to: