Fwd: SCSI-disk
----- Forwarded message from "A.T.J. van den Broek" <tvdbroek@tsc.leica.nl> -----
Date: Wed, 10 Jul 2002 10:39:53 +0200
From: "A.T.J. van den Broek" <tvdbroek@tsc.leica.nl>
Organization: Leica MicroSystems Lithography
X-Mailer: Opera 6.0 build 1010
To: debian-boot@lists.debian.org
Subject: SCSI-disk
Hello,
my name is Ton van den Broek, software engineer at Leica Microsystems Lithography in Best, the Netherlands. Right now we are using OS-9 as operating system, but since we are losing our faith in it
we are considering moving to Linux. We are using an MVME2604 Power PC board, and it looks like Debian is the only one supporting this board. I've downloaded your bootfull.bin from 16 may 2002,
10:12, and boot the CPU-board with TFTP.
That is working, but it doesn't recognize the SCSI-harddisk, which means the end of installing Linux. The drive and cable must be allright, because OS-9 does recognize it.
For your information I have included the two bootsessions here, first the Linux one, then the OS-9 one.
Copyright Motorola Inc. 1988 - 1999, All Rights Reserved
PPC1 Debugger/Diagnostics Release Version 4.3 - 01/20/99 RM01
COLD Start
Local Memory Found =04000000 (&67108864)
MPU Clock Speed =333Mhz
BUS Clock Speed =67Mhz
WARNING: Keyboard Not Connected
Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONE
System Memory: 64MB, ECC Enabled (ECC-Memory Detected)
L2Cache: 256KB
SelfTest/Boots about to Begin... Press <BREAK> at anytime to Abort ALL
NetBoot about to Begin... Press <ESC> to Bypass, <SPC> to Continue
Network Booting from: DEC21140, Controller 0, Device 0
Device Name: /pci@80000000/pci1011,9@e,0:0,0
Loading: bootfull.bin
Client IP Address = 192.168.8.241
Server IP Address = 192.168.8.172
Gateway IP Address = 192.168.8.1
Subnet IP Address Mask = 255.255.255.0
Boot File Name = bootfull.bin
Argument File Name =
Network Boot File load in progress... To abort hit <BREAK>
Bytes Received =&2245162, Bytes Loaded =&2245162
Bytes/Second =&140322, Elapsed Time =16 Second(s)
loaded at: 001F0400 00207220
relocated to: 00800000 00816E20
board data at: 00810314 00816D20
relocated to: 00810314 00816D20
zimage at: 001FB400 002ACC57
relocated to: 00817000 008C8857
initrd at: 002ACC57 0041244D
relocated to: 008C9000 00A2E7F6
avail ram: 00400000 00800000
Linux/PPC load: root=/dev/ram ip=off
Uncompressing Linux...done.
Now booting the kernel
PReP architecture
Total memory = 32MB; using 128kB for hash table (at c01e0000)
Linux version 2.2.20PREP (root@flan) (gcc version 2.95.4 20011002 (Debian prerel
ease)) #1 Thu May 16 10:55:55 EDT 2002
Boot arguments: root=/dev/ram ip=off
time_init: decrementer frequency = 1000013880/60 (15MHz)
Calibrating delay loop... 222.00 BogoMIPS
Memory: 29020k available (1188k kernel code, 1000k data, 128k init) [c0000000,c2000000]
Dentry hash table entries: 4096 (order 3, 32k)
Buffer cache hash table entries: 32768 (order 5, 128k)
Page cache hash table entries: 8192 (order 3, 32k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Setting PCI interrupts for a "MVME 2600/2700 with MVME761"
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 32768 bhash 32768)
Starting kswapd v 1.5
initialize_kbd: Keyboard reset failed, no ACK
Detected PS/2 Mouse Port.
Serial driver version 4.27 with<4>keyboard: Timeout - AT keyboard not present?
keyboard: Timeout - AT keyboard not present?
MANY_PORTS enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
scsi : 0 hosts.
scsi : detected total.
3c59x.c 18Feb01 Donald Becker and others http://www.scyld.com/network/vortex.html
pcnet32.c: PCI bios is present, checking for devices...
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 128k init 4k pmac 4k open firmware
serial console detected. Disabling virtual terminals.
init started: BusyBox v0.60.3-pre (2002.01.19-22:40+0000) multi-call binary
Copyright Motorola Inc. 1988 - 1999, All Rights Reserved
PPC1 Debugger/Diagnostics Release Version 4.3 - 01/20/99 RM01
COLD Start
Local Memory Found =04000000 (&67108864)
MPU Clock Speed =333Mhz
BUS Clock Speed =67Mhz
WARNING: Keyboard Not Connected
Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONE
System Memory: 64MB, ECC Enabled (ECC-Memory Detected)
L2Cache: 256KB
SelfTest/Boots about to Begin... Press <BREAK> at anytime to Abort ALL
NetBoot about to Begin... Press <ESC> to Bypass, <SPC> to Continue
Network Booting from: DEC21140, Controller 0, Device 0
Device Name: /pci@80000000/pci1011,9@e,0:0,0
Loading: rom
Client IP Address = 192.168.8.241
Server IP Address = 192.168.8.172
Gateway IP Address = 192.168.8.1
Subnet IP Address Mask = 255.255.255.0
Boot File Name = rom
Argument File Name =
Network Boot File load in progress... To abort hit <BREAK>
Bytes Received =&2598360, Bytes Loaded =&2598360
Bytes/Second =&144353, Elapsed Time =18 Second(s)
OS-9 Bootstrap for the PowerPC(tm) (Edition 64)
Now trying to Scan SCSI devices.
Symbios 53C825 @ 0x8ffffe00 SELFID (07) MAXCNT (0x01000000)
ID Vendor Product Rev Block Size Total Blks Disk Size
------------------------------------------------------------------------
0x00 QUANTUM LPS270S 5900 0x00000200 0x000811a7 270749696
Now trying to Boot embedded OS-9000 in-place.
Now searching memory ($000bc490 - $002fa5df) for an OS-9 Kernel...
An OS-9 kernel was found at $000bc490
A valid OS-9 bootfile was found.
+3
+5
Leica Boot Handler started!
July 10, 2002 Wednesday 10:15:59 am
Netinit started!
Creating nessesary files on RAMdisk.
fixmod -u inetdb
Module: inetdb - Fixing header parity - Fixing module CRC
fixmod -u inetdb2
Module: inetdb2 - Fixing header parity - Fixing module CRC
Installing routed.
+8
Installing ISP.
+9
$
----------------------------------------------------------------------------
My question is: how come that OS-9 sees the harddisk, but Linux doesn't?
Would you be able to give me some clues?
Thanks in advance.
With kindest regards
A.T.J. van den Broek
Software engineer
Leica Microsystems Lithography
Technical Support Center
Bedrijfsweg 22-24
5683 CP Best, the Netherlands
Tel: +31 499 336882
Fax: +31 499 336899
--
To UNSUBSCRIBE, email to debian-boot-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
----- End forwarded message -----
--
*------v--------- Installing Debian GNU/Linux 3.0 --------v------*
| <http://www.debian.org/releases/woody/installmanual> |
| debian-imac (potato): <http://debian-imac.sourceforge.net> |
| Chris Tillman tillman@voicetrak.com |
| May the Source be with you |
*----------------------------------------------------------------*
--
To UNSUBSCRIBE, email to debian-powerpc-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: