Re: Installing a Broadcom 4312 rev 02 wifi card
[root@ankou:~]# modprobe -v b43
insmod /lib/modules/2.6.26-1-686/kernel/drivers/pcmcia/pcmcia_core.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/input/input-polldev.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/leds/led-class.ko
insmod /lib/modules/2.6.26-1-686/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/2.6.26-1-686/kernel/net/mac80211/mac80211.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/char/hw_random/rng-core.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/base/firmware_class.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/pcmcia/pcmcia.ko
insmod /lib/modules/2.6.26-1-686/kernel/net/rfkill/rfkill.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/ssb/ssb.ko
insmod /lib/modules/2.6.26-1-686/kernel/drivers/net/wireless/b43/b43.ko
[root@ankou:~]# lsmod | grep b43
b43 110748 0
ssb 33476 1 b43
rfkill 5652 1 b43
pcmcia 29548 2 b43,ssb
firmware_class 6816 2 b43,pcmcia
rng_core 3940 1 b43
mac80211 139680 1 b43
led_class 3908 1 b43
input_polldev 3752 1 b43
pcmcia_core 31892 3 b43,ssb,pcmcia
and then dmesg :
[root@ankou:~]# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-13)
(waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian
4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f6d0000 (usable)
[ 0.000000] BIOS-e820: 000000007f6d0000 - 000000007f6e3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f6e3000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 1142MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f7680] 000f7680
[ 0.000000] Entering add_active_range(0, 0, 521936) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 521936
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 521936
[ 0.000000] On node 0 totalpages: 521936
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2286 pages used for memmap
[ 0.000000] HighMem zone: 290274 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7600, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT 7F6D66B3, 009C (r1 DELL M08 6040000
LTP 0)
[ 0.000000] ACPI: FACP 7F6DEB60, 00F4 (r3 TOSCPL CRESTLNE 6040000
ALAN 1)
[ 0.000000] ACPI: DSDT 7F6D7C3B, 6EB1 (r2 TOSCPL CRESTLNE 6040000
INTL 20060608)
[ 0.000000] ACPI: FACS 7F6E2FC0, 0040
[ 0.000000] ACPI: APIC 7F6DEC54, 0068 (r1 INTEL CRESTLNE 6040000
LOHR 5A)
[ 0.000000] ACPI: HPET 7F6DECBC, 0038 (r1 INTEL CRESTLNE 6040000
LOHR 5A)
[ 0.000000] ACPI: MCFG 7F6DECF4, 003C (r1 INTEL CRESTLNE 6040000
LOHR 5A)
[ 0.000000] ACPI: TCPA 7F6DED30, 0032 (r1 Intel CRESTLNE 6040000
LOHR 5A)
[ 0.000000] ACPI: TMOR 7F6DED62, 0026 (r1 PTLTD 6040000
PTL 3)
[ 0.000000] ACPI: OSFR 7F6DED88, 0072 (r1 TOSHIB A+2nd ID 6040000
TASM 4010000)
[ 0.000000] ACPI: APIC 7F6DEDFA, 0068 (r1 PTLTD APIC
6040000 LTP 0)
[ 0.000000] ACPI: BOOT 7F6DEE62, 0028 (r1 PTLTD $SBFTBL$ 6040000
LTP 1)
[ 0.000000] ACPI: SLIC 7F6DEE8A, 0176 (r1 DELL M08 6040000
LTP 0)
[ 0.000000] ACPI: SSDT 7F6D798E, 02AD (r1 SataRe SataAhci 1000
INTL 20061109)
[ 0.000000] ACPI: SSDT 7F6D78EB, 00A3 (r1 BrtRef DD01BRT 1000
INTL 20061109)
[ 0.000000] ACPI: SSDT 7F6D6CDB, 025F (r1 PmRef Cpu0Tst 3000
INTL 20061109)
[ 0.000000] ACPI: SSDT 7F6D6C35, 00A6 (r1 PmRef Cpu1Tst 3000
INTL 20061109)
[ 0.000000] ACPI: SSDT 7F6D674F, 04E6 (r1 PmRef CpuPm 3000
INTL 20061109)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify
linux-acpi@vger.kernel.org
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap:
80000000:60000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 -
0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 517858
[ 0.000000] Kernel command line:
root=/dev/mapper/LVM_Ankou-Ankou_Slash ro quiet splash vga=791
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 2094.834 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.004000] Memory: 2055780k/2087744k available (1769k kernel code,
30712k reserved, 752k data, 244k init, 1170240k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba4ab - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba4ab (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083861] Calibrating delay using timer specific routine.. 4194.01
BogoMIPS (lpj=8388022)
[ 0.083890] Security Framework initialized
[ 0.083894] SELinux: Disabled at boot.
[ 0.083898] Capability LSM initialized
[ 0.083908] Mount-cache hash table entries: 512
[ 0.084005] Initializing cgroup subsys ns
[ 0.084005] Initializing cgroup subsys cpuacct
[ 0.084005] Initializing cgroup subsys devices
[ 0.084005] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084005] CPU: L2 cache: 3072K
[ 0.084005] CPU: Physical Processor ID: 0
[ 0.084005] CPU: Processor Core ID: 0
[ 0.084005] Intel machine check architecture supported.
[ 0.084005] Intel machine check reporting enabled on CPU#0.
[ 0.084005] using mwait in idle threads.
[ 0.084005] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.112007] ENABLING IO-APIC IRQs
[ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151665] CPU0: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz
stepping 06
[ 0.152009] Booting processor 1/1 ip 6000
[ 0.160010] Initializing CPU#1
[ 0.160010] Calibrating delay using timer specific routine.. 4189.46
BogoMIPS (lpj=8378928)
[ 0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160010] CPU: L2 cache: 3072K
[ 0.160010] CPU: Physical Processor ID: 0
[ 0.160010] CPU: Processor Core ID: 1
[ 0.160010] Intel machine check architecture supported.
[ 0.160010] Intel machine check reporting enabled on CPU#1.
[ 0.240015] CPU1: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz
stepping 06
[ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.244015] Brought up 2 CPUs
[ 0.244015] Total of 2 processors activated (8383.47 BogoMIPS).
[ 0.244015] CPU0 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 0 1
[ 0.244015] CPU1 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 1 0
[ 0.244015] net_namespace: 660 bytes
[ 0.244015] Booting paravirtualized kernel on bare hardware
[ 0.244015] NET: Registered protocol family 16
[ 0.244015] ACPI: bus type pci registered
[ 0.244015] PCI: MCFG configuration 0: base e0000000 segment 0 buses
0 - 255
[ 0.244015] PCI: MCFG area at e0000000 reserved in E820
[ 0.244015] PCI: Using MMCONFIG for extended config space
[ 0.244015] PCI: Using configuration type 1 for base access
[ 0.244015] Setting up standard PCI resources
[ 0.244015] ACPI: EC: Look up EC in DSDT
[ 0.252015] ACPI: BIOS _OSI(Linux) query ignored
[ 0.252015] ACPI: DMI System Vendor: Dell Inc.
[ 0.252015] ACPI: DMI Product Name: Vostro1310
[ 0.252015] ACPI: DMI Product Version: Null
[ 0.252015] ACPI: DMI Board Name: 0H528C
[ 0.252015] ACPI: DMI BIOS Vendor: Dell Inc.
[ 0.252015] ACPI: DMI BIOS Date: 10/09/2008
[ 0.252015] ACPI: Please send DMI info above to
linux-acpi@vger.kernel.org
[ 0.252015] ACPI: If "acpi_osi=Linux" works better, please notify
linux-acpi@vger.kernel.org
[ 0.252015] ACPI: Interpreter enabled
[ 0.252015] ACPI: (supports S0 S3 S4 S5)
[ 0.252015] ACPI: Using IOAPIC for interrupt routing
[ 0.254003] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 0.364022] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.364022] ACPI: EC: driver started in interrupt mode
[ 0.364022] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.364022] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6
ACPI/GPIO/TCO
[ 0.364022] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6
GPIO
[ 0.364022] PCI: Transparent bridge - 0000:00:1e.0
[ 0.364022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.364022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.364022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.364150] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.364273] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.364412] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.376023] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12
14 15)
[ 0.376023] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12
14 15)
[ 0.376023] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12
14 15)
[ 0.376023] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12
14 15)
[ 0.376023] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12
14 15) *0, disabled.
[ 0.376023] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12
14 15)
[ 0.376128] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12
14 15)
[ 0.376231] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12
14 15) *10
[ 0.380023] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.380023] pnp: PnP ACPI init
[ 0.380023] ACPI: bus type pnp registered
[ 0.418528] pnp: PnP ACPI: found 10 devices
[ 0.418528] ACPI: ACPI bus type pnp unregistered
[ 0.418528] PnPBIOS: Disabled by ACPI PNP
[ 0.418528] PCI: Using ACPI for IRQ routing
[ 0.425592] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.425596] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.427167] ACPI: RTC can wake from S4
[ 0.434102] system 00:01: iomem range 0xfed1c000-0xfed1ffff could not
be reserved
[ 0.434104] system 00:01: iomem range 0xfed14000-0xfed17fff could not
be reserved
[ 0.434107] system 00:01: iomem range 0xfed18000-0xfed18fff could not
be reserved
[ 0.434110] system 00:01: iomem range 0xfed19000-0xfed19fff could not
be reserved
[ 0.434112] system 00:01: iomem range 0xe0000000-0xefffffff could not
be reserved
[ 0.434115] system 00:01: iomem range 0xfed20000-0xfed3ffff could not
be reserved
[ 0.434117] system 00:01: iomem range 0xfed40000-0xfed44fff could not
be reserved
[ 0.434120] system 00:01: iomem range 0xfed45000-0xfed8ffff could not
be reserved
[ 0.434126] system 00:04: iomem range 0xfed00000-0xfed003ff could not
be reserved
[ 0.434132] system 00:06: ioport range 0x680-0x69f has been reserved
[ 0.434134] system 00:06: ioport range 0x800-0x80f has been reserved
[ 0.434137] system 00:06: ioport range 0x1000-0x107f has been reserved
[ 0.434139] system 00:06: ioport range 0x1180-0x11bf has been reserved
[ 0.434141] system 00:06: ioport range 0xfe00-0xfe00 has been reserved
[ 0.434144] system 00:06: ioport range 0xff00-0xff7f has been reserved
[ 0.463183] PCI: Bridge: 0000:00:1c.0
[ 0.463183] IO window: 2000-2fff
[ 0.463183] MEM window: 0xc4000000-0xc7ffffff
[ 0.463183] PREFETCH window: 0x00000000cc000000-0x00000000cdffffff
[ 0.463183] PCI: Bridge: 0000:00:1c.1
[ 0.463183] IO window: 3000-3fff
[ 0.463183] MEM window: 0xf0000000-0xf3ffffff
[ 0.463183] PREFETCH window: 0x00000000fa000000-0x00000000fbffffff
[ 0.463183] PCI: Bridge: 0000:00:1c.3
[ 0.463183] IO window: 4000-4fff
[ 0.463183] MEM window: 0xf4000000-0xf7ffffff
[ 0.463183] PREFETCH window: 0x00000000fc000000-0x00000000fdffffff
[ 0.463183] PCI: Bridge: 0000:00:1c.4
[ 0.463183] IO window: 5000-5fff
[ 0.463183] MEM window: 0x88000000-0x880fffff
[ 0.463183] PREFETCH window: 0x00000000f8600000-0x00000000f86fffff
[ 0.463183] PCI: Bridge: 0000:00:1e.0
[ 0.463183] IO window: disabled.
[ 0.463183] MEM window: 0xf8200000-0xf82fffff
[ 0.463183] PREFETCH window: disabled.
[ 0.463183] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level,
low) -> IRQ 17
[ 0.463183] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.463183] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level,
low) -> IRQ 16
[ 0.463183] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.463183] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level,
low) -> IRQ 19
[ 0.463183] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.463183] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level,
low) -> IRQ 17
[ 0.463183] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.463183] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.463183] NET: Registered protocol family 2
[ 0.476524] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[ 0.476708] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.477012] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.479182] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.479185] TCP reno registered
[ 0.486530] NET: Registered protocol family 1
[ 0.486615] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 1
[ 0.510439] Switched to high resolution mode on CPU 0
[ 0.814990] it is
[ 1.164938] Freeing initrd memory: 10224k freed
[ 1.166993] Simple Boot Flag at 0x36 set to 0x1
[ 1.169119] audit: initializing netlink socket (disabled)
[ 1.169140] type=2000 audit(1235748400.156:1): initialized
[ 1.170994] highmem bounce pool size: 64 pages
[ 1.170994] Total HugeTLB memory allocated, 0
[ 1.170994] VFS: Disk quotas dquot_6.5.1
[ 1.170994] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.170994] msgmni has been set to 1751
[ 1.170994] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 1.170994] io scheduler noop registered
[ 1.170994] io scheduler anticipatory registered
[ 1.170994] io scheduler deadline registered
[ 1.170994] io scheduler cfq registered (default)
[ 1.170994] pci 0000:00:02.0: Boot video device
[ 1.170994] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.170994] assign_interrupt_mode Found MSI capability
[ 1.170994] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.170994] Allocate Port Service[0000:00:1c.0:pcie02]
[ 1.170994] Allocate Port Service[0000:00:1c.0:pcie03]
[ 1.170994] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.170994] assign_interrupt_mode Found MSI capability
[ 1.170994] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.170994] Allocate Port Service[0000:00:1c.1:pcie02]
[ 1.170994] Allocate Port Service[0000:00:1c.1:pcie03]
[ 1.170994] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 1.170994] assign_interrupt_mode Found MSI capability
[ 1.170994] Allocate Port Service[0000:00:1c.3:pcie00]
[ 1.170994] Allocate Port Service[0000:00:1c.3:pcie02]
[ 1.170994] Allocate Port Service[0000:00:1c.3:pcie03]
[ 1.170994] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 1.170994] assign_interrupt_mode Found MSI capability
[ 1.170994] Allocate Port Service[0000:00:1c.4:pcie00]
[ 1.170994] Allocate Port Service[0000:00:1c.4:pcie02]
[ 1.170994] Allocate Port Service[0000:00:1c.4:pcie03]
[ 1.170994] vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000,
using 3072k, total 7616k
[ 1.170994] vesafb: mode is 1024x768x16, linelength=2048, pages=3
[ 1.170994] vesafb: scrolling: redraw
[ 1.170994] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 1.183971] Console: switching to colour frame buffer device 128x48
[ 1.195979] fb0: VESA VGA frame buffer device
[ 1.198993] isapnp: Scanning for PnP cards...
[ 1.505570] isapnp: No Plug & Play device found
[ 1.507607] hpet_resources: 0xfed00000 is busy
[ 1.507653] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 1.509110] brd: module loaded
[ 1.509185] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 1.553725] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.553729] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.554737] mice: PS/2 mouse device common for all mice
[ 1.554737] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.554737] rtc0: alarms up to one month, y3k
[ 1.554737] cpuidle: using governor ladder
[ 1.554737] cpuidle: using governor menu
[ 1.554737] No iBFT detected.
[ 1.554737] TCP cubic registered
[ 1.554737] NET: Registered protocol family 17
[ 1.554737] Using IPI No-Shortcut mode
[ 1.554737] registered taskstats version 1
[ 1.554737] rtc_cmos 00:07: setting system clock to 2009-02-27
15:26:41 UTC (1235748401)
[ 1.554737] Freeing unused kernel memory: 244k freed
[ 1.584555] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.676657] ACPI: SSDT 7F6D75A9, 027A (r1 PmRef Cpu0Ist 3000
INTL 20061109)
[ 1.676657] ACPI: SSDT 7F6D6F3A, 05EA (r1 PmRef Cpu0Cst 3001
INTL 20061109)
[ 1.680657] Monitor-Mwait will be used to enter C-1 state
[ 1.680657] Monitor-Mwait will be used to enter C-2 state
[ 1.680657] Monitor-Mwait will be used to enter C-3 state
[ 1.680660] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.680660] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.680660] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.680660] ACPI: SSDT 7F6D7823, 00C8 (r1 PmRef Cpu1Ist 3000
INTL 20061109)
[ 1.680660] ACPI: SSDT 7F6D7524, 0085 (r1 PmRef Cpu1Cst 3000
INTL 20061109)
[ 1.680660] Marking TSC unstable due to: TSC halts in idle.
[ 1.680657] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 1.680657] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.680657] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.897826] usbcore: registered new interface driver usbfs
[ 1.897826] usbcore: registered new interface driver hub
[ 1.897826] usbcore: registered new device driver usb
[ 1.897826] USB Universal Host Controller Interface driver v3.0
[ 1.897826] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 1.897826] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.897826] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.897826] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 1.897826] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 1.897893] usb usb1: configuration #1 chosen from 1 choice
[ 1.897914] hub 1-0:1.0: USB hub found
[ 1.897918] hub 1-0:1.0: 2 ports detected
[ 1.983199] No dock devices found.
[ 1.992463] SCSI subsystem initialized
[ 2.004389] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.004392] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.004394] usb usb1: Product: UHCI Host Controller
[ 2.004396] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.004397] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.008278] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level,
low) -> IRQ 21
[ 2.008278] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 2.008278] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.008278] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned
bus number 2
[ 2.008278] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 2.008278] usb usb2: configuration #1 chosen from 1 choice
[ 2.008278] hub 2-0:1.0: USB hub found
[ 2.008278] hub 2-0:1.0: 2 ports detected
[ 2.008278] libata version 3.00 loaded.
[ 2.017010] sdhci: Secure Digital Host Controller Interface driver
[ 2.017010] sdhci: Copyright(c) Pierre Ossman
[ 2.112969] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.112979] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.112981] usb usb2: Product: UHCI Host Controller
[ 2.112983] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.112984] usb usb2: SerialNumber: 0000:00:1a.1
[ 2.112969] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level,
low) -> IRQ 18
[ 2.112969] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 2.112969] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.112969] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned
bus number 3
[ 2.117779] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.117779] PCI: cache line size of 32 is not supported by device
0000:00:1a.7
[ 2.117779] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf8504800
[ 2.133879] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 2.133963] usb usb3: configuration #1 chosen from 1 choice
[ 2.133992] hub 3-0:1.0: USB hub found
[ 2.133996] hub 3-0:1.0: 4 ports detected
[ 2.238606] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.238608] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.238610] usb usb3: Product: EHCI Host Controller
[ 2.238612] usb usb3: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.238614] usb usb3: SerialNumber: 0000:00:1a.7
[ 2.238606] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 23
[ 2.238606] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.238606] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.238606] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 4
[ 2.238606] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[ 2.238606] usb usb4: configuration #1 chosen from 1 choice
[ 2.238606] hub 4-0:1.0: USB hub found
[ 2.238606] hub 4-0:1.0: 2 ports detected
[ 2.341491] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.341495] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.341499] usb usb4: Product: UHCI Host Controller
[ 2.341502] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.341505] usb usb4: SerialNumber: 0000:00:1d.0
[ 2.342921] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
[ 2.342921] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.342921] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.342921] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 5
[ 2.342921] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[ 2.342921] usb usb5: configuration #1 chosen from 1 choice
[ 2.342921] hub 5-0:1.0: USB hub found
[ 2.342921] hub 5-0:1.0: 2 ports detected
[ 2.445452] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.445457] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.445461] usb usb5: Product: UHCI Host Controller
[ 2.445464] usb usb5: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.445467] usb usb5: SerialNumber: 0000:00:1d.1
[ 2.446920] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 2.446920] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.446920] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.446920] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 6
[ 2.446920] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[ 2.446920] usb usb6: configuration #1 chosen from 1 choice
[ 2.446920] hub 6-0:1.0: USB hub found
[ 2.446920] hub 6-0:1.0: 2 ports detected
[ 2.525371] Clocksource tsc unstable (delta = -446125405 ns)
[ 2.549431] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.549436] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.549439] usb usb6: Product: UHCI Host Controller
[ 2.549442] usb usb6: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.549445] usb usb6: SerialNumber: 0000:00:1d.2
[ 2.550876] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 23
[ 2.550876] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.550876] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.550876] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 7
[ 2.554305] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.554305] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 2.554305] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8504c00
[ 2.645141] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 2.645213] usb usb7: configuration #1 chosen from 1 choice
[ 2.645235] hub 7-0:1.0: USB hub found
[ 2.645239] hub 7-0:1.0: 6 ports detected
[ 2.749038] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.749040] usb usb7: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.749042] usb usb7: Product: EHCI Host Controller
[ 2.749044] usb usb7: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.749045] usb usb7: SerialNumber: 0000:00:1d.7
[ 2.753780] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[ 2.753780] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 2.753780] PCI: Setting latency timer of device 0000:07:00.0 to 64
[ 2.753780] eth0: RTL8168c/8111c at 0xf8836000, 00:21:70:c1:50:69,
XID 3c2000c0 IRQ 219
[ 2.753780] ACPI: PCI Interrupt 0000:08:05.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 2.753780] ahci 0000:00:1f.2: version 3.0
[ 2.753780] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 18 (level,
low) -> IRQ 18
[ 2.804870] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]
MMIO=[f8200000-f82007ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 2.920691] usb 3-3: new high speed USB device using ehci_hcd and
address 3
[ 3.094020] usb 3-3: configuration #1 chosen from 1 choice
[ 3.096039] usb 3-3: New USB device found, idVendor=0c45, idProduct=63e0
[ 3.096039] usb 3-3: New USB device strings: Mfr=2, Product=1,
SerialNumber=3
[ 3.096039] usb 3-3: Product: Integrated Webcam
[ 3.096039] usb 3-3: Manufacturer: SONiX Technology Inc
[ 3.096039] usb 3-3: SerialNumber: M09-001
[ 3.337208] usb 1-1: new full speed USB device using uhci_hcd and
address 2
[ 3.512748] usb 1-1: configuration #1 chosen from 1 choice
[ 3.514446] usb 1-1: New USB device found, idVendor=0483, idProduct=2016
[ 3.514446] usb 1-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 3.514446] usb 1-1: Product: Biometric Coprocessor
[ 3.514446] usb 1-1: Manufacturer: STMicroelectronics
[ 3.664015] atkbd.c: Unknown key pressed (translated set 2, code 0x8e
on isa0060/serio0).
[ 3.664015] atkbd.c: Use 'setkeycodes e00e <keycode>' to make it known.
[ 3.761699] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps
0x7 impl SATA mode
[ 3.761704] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio
slum part
[ 3.761712] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.762581] scsi0 : ahci
[ 3.762581] scsi1 : ahci
[ 3.762581] scsi2 : ahci
[ 3.762581] ata1: SATA max UDMA/133 abar m2048@0xf8504000 port
0xf8504100 irq 218
[ 3.762581] ata2: SATA max UDMA/133 abar m2048@0xf8504000 port
0xf8504180 irq 218
[ 3.762581] ata3: SATA max UDMA/133 abar m2048@0xf8504000 port
0xf8504200 irq 218
[ 4.082355] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.082328] ieee1394: Host added: ID:BUS[0-00:1023]
GUID[00000010a000b000]
[ 4.085980] ata1.00: _GTF unexpected object type 0x1
[ 4.126621] ata1.00: ATA-8: WDC WD2500BEVT-75ZCT2, 11.01A11, max UDMA/133
[ 4.126621] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.128229] ata1.00: _GTF unexpected object type 0x1
[ 4.128342] ata1.00: configured for UDMA/133
[ 4.464516] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.801577] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.816481] scsi 0:0:0:0: Direct-Access ATA WDC WD2500BEVT-7
11.0 PQ: 0 ANSI: 5
[ 4.825747] sdhci: SDHCI controller found at 0000:08:05.2 [1217:7120]
(rev 2)
[ 4.825747] ACPI: PCI Interrupt 0000:08:05.2[A] -> GSI 22 (level,
low) -> IRQ 22
[ 4.825747] mmc0: Unknown controller version (2). You may experience
problems.
[ 4.825747] mmc0: SDHCI at 0xf8202800 irq 22 DMA
[ 4.827110] Uniform Multi-Platform E-IDE driver
[ 4.827113] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 4.834447] ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI
slot 0000:00:1f.1
[ 4.834447] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
[ 4.834447] ICH8M: not 100% native mode: will probe irqs later
[ 4.834447] ide0: BM-DMA at 0x1810-0x1817
[ 4.834447] ide1: BM-DMA at 0x1818-0x181f
[ 4.834447] Probing IDE interface ide0...
[ 4.854760] Driver 'sd' needs updating - please use bus_type methods
[ 4.854760] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 4.854760] sd 0:0:0:0: [sda] Write Protect is off
[ 4.854760] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.854760] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.854760] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 4.854760] sd 0:0:0:0: [sda] Write Protect is off
[ 4.854760] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.854760] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.854760] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 4.916284] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.570197] hda: Optiarc DVD+/-RW AD-7640A, ATAPI CD/DVD-ROM drive
[ 6.241848] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 6.242208] hda: UDMA/33 mode selected
[ 6.242623] Probing IDE interface ide1...
[ 6.810092] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.810733] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.835324] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 6.835324] Uniform CD-ROM driver Revision: 3.20
[ 6.955057] device-mapper: uevent: version 1.0.3
[ 6.955057] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18)
initialised: dm-devel@redhat.com
[ 25.722294] PM: Starting manual resume from disk
[ 26.835734] kjournald starting. Commit interval 5 seconds
[ 26.835734] EXT3-fs: mounted filesystem with ordered data mode.
[ 29.923651] udevd version 125 started
[ 30.181294] dcdbas dcdbas: Dell Systems Management Base Driver
(version 5.6.0-3.2)
[ 30.345329] Linux agpgart interface v0.103
[ 30.365505] agpgart: Detected an Intel 965GM Chipset.
[ 30.366353] agpgart: Detected 7676K stolen memory.
[ 30.379477] agpgart: AGP aperture is 256M @ 0xd0000000
[ 30.393896] input: Power Button (FF) as /class/input/input1
[ 30.437897] intelfb: Framebuffer driver for Intel(R)
830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets
[ 30.437897] intelfb: Version 0.9.5
[ 30.437897] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 30.437897] intelfb: Cannot reserve FB region.
[ 30.443735] ACPI: Power Button (FF) [PWRF]
[ 30.443818] input: Lid Switch as /class/input/input2
[ 30.476224] ACPI: Lid Switch [LID0]
[ 30.476283] input: Power Button (CM) as /class/input/input3
[ 30.540329] ACPI: Power Button (CM) [PWRB]
[ 30.540392] input: Sleep Button (CM) as /class/input/input4
[ 30.605512] ACPI: Sleep Button (CM) [SLPB]
[ 30.606582] ACPI: WMI: Mapper loaded
[ 30.615028] ACPI: device:05 is registered as cooling_device2
[ 30.615189] input: Video Bus as /class/input/input5
[ 30.670653] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 30.686583] ACPI: device:0a is registered as cooling_device3
[ 30.686583] input: Video Bus as /class/input/input6
[ 30.734633] ACPI: Video Device [GFX0] (multi-head: yes rom: no
post: no)
[ 30.739121] ACPI: AC Adapter [ACAD] (off-line)
[ 30.802607] Linux video capture interface: v2.00
[ 30.810327] ieee80211_crypt: registered algorithm 'NULL'
[ 31.002917] ACPI: Battery Slot [BAT1] (battery present)
[ 31.019122] wl: module license 'unspecified' taints kernel.
[ 31.019123] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 19 (level,
low) -> IRQ 19
[ 31.019123] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 31.292781] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 31.377360] ieee80211_crypt: registered algorithm 'TKIP'
[ 31.445965] eth1: Broadcom BCM4315 802.11 Wireless Controller 5.10.27.14
[ 31.445996] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 31.445996] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 31.455989] uvcvideo: Found UVC 1.00 device Integrated Webcam (0c45:63e0)
[ 31.470975] input: Integrated Webcam as /class/input/input7
[ 31.476755] usbcore: registered new interface driver uvcvideo
[ 31.476759] USB Video Class driver (v0.1.0)
[ 31.483893] hda_codec: Unknown model for ALC268, trying auto-probe
from BIOS...
[ 31.519922] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level,
low) -> IRQ 18
[ 31.721361] input: PS/2 Mouse as /class/input/input8
[ 31.761610] input: AlpsPS/2 ALPS GlidePoint as /class/input/input9
[ 31.779458] input: PC Speaker as /class/input/input10
[ 31.816723] iTCO_wdt: Found a ICH8M TCO device (Version=2,
TCOBASE=0x1060)
[ 31.816723] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 31.870976] Error: Driver 'pcspkr' is already registered, aborting...
[ 32.479370] EXT3 FS on dm-3, internal journal
[ 32.705707] loop: module loaded
[ 32.944104] Broadcom 43xx driver loaded [ Features: PMLR,
Firmware-ID: FW13 ]
[ 34.558229] kjournald starting. Commit interval 5 seconds
[ 34.558449] EXT3 FS on sda5, internal journal
[ 34.558449] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.651184] kjournald starting. Commit interval 5 seconds
[ 34.651394] EXT3 FS on dm-4, internal journal
[ 34.651394] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.738619] kjournald starting. Commit interval 5 seconds
[ 34.738808] EXT3 FS on dm-2, internal journal
[ 34.738808] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.799949] Adding 4194296k swap on
/dev/mapper/LVM_Ankou-Ankou_Swap. Priority:-1 extents:1 across:4194296k
[ 36.381827] r8169: eth0: link down
[ 39.059245] NET: Registered protocol family 10
[ 39.059245] lo: Disabled Privacy Extensions
[ 39.059640] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.109811] lp: driver loaded but no devices found
[ 40.151543] ppdev: user-space parallel port driver
[ 46.520544] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 47.039610] ACPI Exception (evregion-0420): AE_TIME, Returned by
Handler for [EmbeddedControl] [20080321]
[ 47.039621] ACPI Error (psparse-0530): Method parse/execution failed
[\_SB_.PCI0.LPCB.BAT1._BST] (Node f703ddec), AE_TIME
[ 47.039664] ACPI Exception (battery-0360): AE_TIME, Evaluating _BST
[20080321]
[ 51.223867] Bluetooth: Core ver 2.11
[ 51.224488] NET: Registered protocol family 31
[ 51.224492] Bluetooth: HCI device and connection manager initialized
[ 51.224495] Bluetooth: HCI socket layer initialized
[ 51.284239] Bluetooth: L2CAP ver 2.9
[ 51.284244] Bluetooth: L2CAP socket layer initialized
[ 51.600479] Bluetooth: RFCOMM socket layer initialized
[ 51.600479] Bluetooth: RFCOMM TTY layer initialized
[ 51.600479] Bluetooth: RFCOMM ver 1.8
[ 55.938283] eth1: no IPv6 routers present
[ 57.359070] [drm] Initialized drm 1.1.0 20060810
[ 57.370829] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 57.370829] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 118.916426] ACPI: PCI interrupt for device 0000:06:00.0 disabled
[ 171.861587] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 19 (level,
low) -> IRQ 19
[ 171.861587] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 171.881532] eth1: Broadcom BCM4315 802.11 Wireless Controller 5.10.27.14
[ 177.871336] ACPI: PCI interrupt for device 0000:06:00.0 disabled
[ 319.821814] r8169: eth0: link up
[ 319.821814] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 330.569521] eth0: no IPv6 routers present
[ 352.349648] r8169: eth0: link up
[ 362.912440] eth0: no IPv6 routers present
[ 630.553689] Broadcom 43xx driver loaded [ Features: PMLR,
Firmware-ID: FW13 ]
it seems weird that there is only one line about the b43 module...
this is the lspci output:
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 2 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 4 (rev 03)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 5 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface
Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
IDE Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller
(rev 03)
06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller
(rev 02)
08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD
Controller (rev 01)
an idea ?
Celejar wrote:
> On Fri, 27 Feb 2009 14:46:06 +0100
> Korrignu <korrignu@gmail.com> wrote:
>
>
>> hi,
>> i have some problems since i bought my new laptop
>> in fact i have a wifi card with a briadcom 4312 rev 02 chipset
>> and i don't know how to set up
>> i installed b43-fwcutter and then i load b43 module
>> but nothing happens
>> no new wireless interface etc...
>>
>> so i don't know if this chipset is supported by the b43 module
>>
>> if i install the broadcom STA/wl module, it works asa long as i don't
>> want to use a WPA-EAP with TTLS wifi network
>> because this lead to a kernel panic ...
>>
>> have I somebody already installed this kind of wifi card ? and how ?
>> or have sombedy have some informations to do that ?
>>
>
> The 4312 is listed as supported:
>
> http://wireless.kernel.org/en/users/Drivers/b43#supported
>
> Post the relevant dmesg excerpt and lspci output.
>
> Celejar
> --
> mailmin.sourceforge.net - remote access via secure (OpenPGP) email
> ssuds.sourceforge.net - A Simple Sudoku Solver and Generator
>
>
>
Reply to: