Re: PCMCIA CardBus USB Adapter
I don't understand why is that happening. if you don't get any anwsers try
posting to debian-user@lists....
maybe they could help, since there's more people on that list..
On Sunday 31 October 2004 22:15, Tom Sahrendt wrote:
> Hi Rui,
>
> I think the problem has somehow to do with IRQ 11. I
> tried to modprobe usb_storgae before plugging in.
> Output follows:
>
> kernel: Initializing USB Mass Storage driver...
> kernel: usbcore: registered new driver usb-storage
> kernel: USB Mass Storage support registered.
> kernel: Linux Kernel Card Services
> kernel: options: [pci] [cardbus] [pm]
> kernel: ACPI: PCI interrupt 0000:00:11.0[A] -> GSI 11
> (level, low) -> IRQ 11
> kernel: Yenta: CardBus bridge found at 0000:00:11.0
> [0e11:b121]
> kernel: Yenta: Using CSCINT to route CSC interrupts to
> PCI
> kernel: Yenta: Routing CardBus interrupts to PCI
> kernel: Yenta TI: socket 0000:00:11.0, mfunc
> 0x01001c72, devctl 0x64
> kernel: Yenta: ISA IRQ mask 0x0418, PCI irq 11
> kernel: Socket status: 30000006
> kernel: ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11
> (level, low) -> IRQ 11
> kernel: Yenta: CardBus bridge found at 0000:00:11.1
> [0e11:b121]
> kernel: Yenta: Using CSCINT to route CSC interrupts to
> PCI
> kernel: Yenta: Routing CardBus interrupts to PCI
> kernel: Yenta TI: socket 0000:00:11.1, mfunc
> 0x01001c72, devctl 0x64
> kernel: Yenta: ISA IRQ mask 0x0418, PCI irq 11
> kernel: Socket status: 30000020
> kernel: [__report_bad_irq+42/144]
> __report_bad_irq+0x2a/0x90
> kernel: [note_interrupt+112/176]
> note_interrupt+0x70/0xb0
> kernel: [do_IRQ+288/304] do_IRQ+0x120/0x130
> kernel: [common_interrupt+24/32]
> common_interrupt+0x18/0x20
> kernel: [__crc_d_move+789653/1607282]
> hci_sock_getsockopt+0xdb/0x130 [bluetooth]
> kernel: [__do_softirq+46/128] __do_softirq+0x2e/0x80
> kernel: [do_softirq+39/48] do_softirq+0x27/0x30
> kernel: [do_IRQ+251/304] do_IRQ+0xfb/0x130
> kernel: [common_interrupt+24/32]
> common_interrupt+0x18/0x20
> kernel: [schedule+907/1232] schedule+0x38b/0x4d0
> kernel: [default_idle+35/64] default_idle+0x23/0x40
> kernel: [cpu_idle+52/64] cpu_idle+0x34/0x40
> kernel: [start_kernel+424/496]
> start_kernel+0x1a8/0x1f0
> kernel: [unknown_bootoption+0/352]
> unknown_bootoption+0x0/0x160
> kernel: cs: IO port probe 0x0100-0x04ff: excluding
> 0x250-0x257 0x330-0x337 0x388-0x38f 0x4d0-0x4d7
> kernel: cs: IO port probe 0x0800-0x08ff: clean.
> kernel: cs: IO port probe 0x0c00-0x0cff: clean.
> kernel: cs: IO port probe 0x0a00-0x0aff: clean.
> pci.agent[1583]: ehci-hcd: loaded successfully
> pci.agent[1582]: ohci-hcd: loaded successfully
> kernel: PCI: Enabling device 0000:05:00.0 (0000 ->
> 0002)
> kernel: ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 11
> (level, low) -> IRQ 11
> kernel: ohci_hcd 0000:05:00.0: ALi Corporation USB 1.1
> Controller
> kernel: ohci_hcd 0000:05:00.0: irq 11, pci mem
> ca99b000
> kernel: ohci_hcd 0000:05:00.0: new USB bus registered,
> assigned bus number 1
> kernel: hub 1-0:1.0: USB hub found
> kernel: hub 1-0:1.0: 2 ports detected
> kernel: PCI: Enabling device 0000:05:00.3 (0000 ->
> 0002)
> kernel: ACPI: PCI interrupt 0000:05:00.3[A] -> GSI 11
> (level, low) -> IRQ 11
> kernel: ehci_hcd 0000:05:00.3: ALi Corporation USB 2.0
> Controller
> kernel: ehci_hcd 0000:05:00.3: irq 11, pci mem
> ca9c9000
> kernel: ehci_hcd 0000:05:00.3: new USB bus registered,
> assigned bus number 2
> kernel: ehci_hcd 0000:05:00.3: USB 2.0 enabled, EHCI
> 1.00, driver 2004-May-10
> kernel: hub 2-0:1.0: USB hub found
> kernel: hub 2-0:1.0: 6 ports detected
> kernel: usb 2-1: new high speed USB device using
> address 2
> usb.agent[1664]: usbcore: already loaded
> usb.agent[1649]: usbcore: already loaded
> kernel: usb 2-1: control timeout on ep0out
> kernel: ehci_hcd 0000:05:00.3: Unlink after no-IRQ?
> Different ACPI or APIC settings may help.
> kernel: usb 2-1: control timeout on ep0out
> kernel: usb 2-1: new high speed USB device using
> address 3
> kernel: usb 2-1: control timeout on ep0out
> kernel: usb 2-1: control timeout on ep0out
> kernel: Disabling IRQ #11
> kernel: PCI: Enabling device 0000:05:00.0 (0000 ->
> 0002)
> kernel: PCI: Enabling device 0000:05:00.3 (0000 ->
> 0002)
> kernel: usb 2-1: device not accepting address 3, error
> -110
>
> lsmod
>
> Module Size Used by
> ehci_hcd 32004 0
> ohci_hcd 21764 0
> ds 18756 4
> yenta_socket 21728 1
> pcmcia_core 70900 2 ds,yenta_socket
> usb_storage 68832 0
> snd_es1688 8008 0
> snd 57156 11
> snd_es1688,snd_opl3_lib,snd_hwdep,snd_es1688_lib,snd_pcm_oss,snd_mixer_oss,
>snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device soundcore
> 10336 1 snd
> ipv6 264612 8
> usbcore 119012 5
> ehci_hcd,ohci_hcd,usb_storage
> lp 11176 0
> dm_mod 59772 0
> capability 4520 0
> commoncap 7232 1 capability
> nls_iso8859_1 4032 0
> nls_cp437 5696 0
> vfat 14656 0
> fat 46784 1 vfat
> floppy 61200 0
> parport_pc 35392 1
> parport 41832 2 lp,parport_pc
> tsdev 7392 0
> mousedev 10476 1
> evdev 9600 0
> psmouse 20360 0
> rtc 12760 0
> ext2 71848 1
> ext3 127240 0
> jbd 62616 1 ext3
> mbcache 9348 2 ext2,ext3
> ide_generic 1408 0
> piix 13440 1
> ide_disk 19296 3
> ide_core 139940 4
> usb_storage,ide_generic,piix,ide_disk
> sd_mod 21696 0
> ata_piix 8164 0
> libata 41604 1 ata_piix
> scsi_mod 125196 3
> usb_storage,sd_mod,libata
> unix 28692 18
> font 8320 0
> vesafb 6656 0
> cfbcopyarea 3840 1 vesafb
> cfbimgblt 3040 1 vesafb
> cfbfillrect 3776 1 vesafb
>
> cardctl status
>
> Socket 0:
> no card
> Socket 1:
> 3.3V CardBus card
> function 0: [ready]
> function 1: [ready]
>
> cardctl info
>
> PRODID_1=""
> PRODID_2=""
> PRODID_3=""
> PRODID_4=""
> MANFID=0000,0000
> FUNCID=255
> PRODID_1=""
> PRODID_2=""
> PRODID_3=""
> PRODID_4=""
> MANFID=0000,0000
> FUNCID=255
>
> cardctl ident:
>
> Socket 0:
> no product info available
> Socket 1:
> no product info available
>
>
>
>
>
>
>
> ___________________________________________________________ALL-NEW Yahoo!
> Messenger - all new features - even more fun! http://uk.messenger.yahoo.com
--
Rui Silva
ruka@tugamail.com
Debian GNU/Linux
Reply to: