Re: PCMCIA CardBus USB Adapter
Hi Rui,
I think the problem has somehow to do with IRQ 11. I
tried to modprobe usb_storgae before plugging in.
Output follows:
kernel: Initializing USB Mass Storage driver...
kernel: usbcore: registered new driver usb-storage
kernel: USB Mass Storage support registered.
kernel: Linux Kernel Card Services
kernel: options: [pci] [cardbus] [pm]
kernel: ACPI: PCI interrupt 0000:00:11.0[A] -> GSI 11
(level, low) -> IRQ 11
kernel: Yenta: CardBus bridge found at 0000:00:11.0
[0e11:b121]
kernel: Yenta: Using CSCINT to route CSC interrupts to
PCI
kernel: Yenta: Routing CardBus interrupts to PCI
kernel: Yenta TI: socket 0000:00:11.0, mfunc
0x01001c72, devctl 0x64
kernel: Yenta: ISA IRQ mask 0x0418, PCI irq 11
kernel: Socket status: 30000006
kernel: ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11
(level, low) -> IRQ 11
kernel: Yenta: CardBus bridge found at 0000:00:11.1
[0e11:b121]
kernel: Yenta: Using CSCINT to route CSC interrupts to
PCI
kernel: Yenta: Routing CardBus interrupts to PCI
kernel: Yenta TI: socket 0000:00:11.1, mfunc
0x01001c72, devctl 0x64
kernel: Yenta: ISA IRQ mask 0x0418, PCI irq 11
kernel: Socket status: 30000020
kernel: [__report_bad_irq+42/144]
__report_bad_irq+0x2a/0x90
kernel: [note_interrupt+112/176]
note_interrupt+0x70/0xb0
kernel: [do_IRQ+288/304] do_IRQ+0x120/0x130
kernel: [common_interrupt+24/32]
common_interrupt+0x18/0x20
kernel: [__crc_d_move+789653/1607282]
hci_sock_getsockopt+0xdb/0x130 [bluetooth]
kernel: [__do_softirq+46/128] __do_softirq+0x2e/0x80
kernel: [do_softirq+39/48] do_softirq+0x27/0x30
kernel: [do_IRQ+251/304] do_IRQ+0xfb/0x130
kernel: [common_interrupt+24/32]
common_interrupt+0x18/0x20
kernel: [schedule+907/1232] schedule+0x38b/0x4d0
kernel: [default_idle+35/64] default_idle+0x23/0x40
kernel: [cpu_idle+52/64] cpu_idle+0x34/0x40
kernel: [start_kernel+424/496]
start_kernel+0x1a8/0x1f0
kernel: [unknown_bootoption+0/352]
unknown_bootoption+0x0/0x160
kernel: cs: IO port probe 0x0100-0x04ff: excluding
0x250-0x257 0x330-0x337 0x388-0x38f 0x4d0-0x4d7
kernel: cs: IO port probe 0x0800-0x08ff: clean.
kernel: cs: IO port probe 0x0c00-0x0cff: clean.
kernel: cs: IO port probe 0x0a00-0x0aff: clean.
pci.agent[1583]: ehci-hcd: loaded successfully
pci.agent[1582]: ohci-hcd: loaded successfully
kernel: PCI: Enabling device 0000:05:00.0 (0000 ->
0002)
kernel: ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 11
(level, low) -> IRQ 11
kernel: ohci_hcd 0000:05:00.0: ALi Corporation USB 1.1
Controller
kernel: ohci_hcd 0000:05:00.0: irq 11, pci mem
ca99b000
kernel: ohci_hcd 0000:05:00.0: new USB bus registered,
assigned bus number 1
kernel: hub 1-0:1.0: USB hub found
kernel: hub 1-0:1.0: 2 ports detected
kernel: PCI: Enabling device 0000:05:00.3 (0000 ->
0002)
kernel: ACPI: PCI interrupt 0000:05:00.3[A] -> GSI 11
(level, low) -> IRQ 11
kernel: ehci_hcd 0000:05:00.3: ALi Corporation USB 2.0
Controller
kernel: ehci_hcd 0000:05:00.3: irq 11, pci mem
ca9c9000
kernel: ehci_hcd 0000:05:00.3: new USB bus registered,
assigned bus number 2
kernel: ehci_hcd 0000:05:00.3: USB 2.0 enabled, EHCI
1.00, driver 2004-May-10
kernel: hub 2-0:1.0: USB hub found
kernel: hub 2-0:1.0: 6 ports detected
kernel: usb 2-1: new high speed USB device using
address 2
usb.agent[1664]: usbcore: already loaded
usb.agent[1649]: usbcore: already loaded
kernel: usb 2-1: control timeout on ep0out
kernel: ehci_hcd 0000:05:00.3: Unlink after no-IRQ?
Different ACPI or APIC settings may help.
kernel: usb 2-1: control timeout on ep0out
kernel: usb 2-1: new high speed USB device using
address 3
kernel: usb 2-1: control timeout on ep0out
kernel: usb 2-1: control timeout on ep0out
kernel: Disabling IRQ #11
kernel: PCI: Enabling device 0000:05:00.0 (0000 ->
0002)
kernel: PCI: Enabling device 0000:05:00.3 (0000 ->
0002)
kernel: usb 2-1: device not accepting address 3, error
-110
lsmod
Module Size Used by
ehci_hcd 32004 0
ohci_hcd 21764 0
ds 18756 4
yenta_socket 21728 1
pcmcia_core 70900 2 ds,yenta_socket
usb_storage 68832 0
snd_es1688 8008 0
snd 57156 11
snd_es1688,snd_opl3_lib,snd_hwdep,snd_es1688_lib,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 10336 1 snd
ipv6 264612 8
usbcore 119012 5
ehci_hcd,ohci_hcd,usb_storage
lp 11176 0
dm_mod 59772 0
capability 4520 0
commoncap 7232 1 capability
nls_iso8859_1 4032 0
nls_cp437 5696 0
vfat 14656 0
fat 46784 1 vfat
floppy 61200 0
parport_pc 35392 1
parport 41832 2 lp,parport_pc
tsdev 7392 0
mousedev 10476 1
evdev 9600 0
psmouse 20360 0
rtc 12760 0
ext2 71848 1
ext3 127240 0
jbd 62616 1 ext3
mbcache 9348 2 ext2,ext3
ide_generic 1408 0
piix 13440 1
ide_disk 19296 3
ide_core 139940 4
usb_storage,ide_generic,piix,ide_disk
sd_mod 21696 0
ata_piix 8164 0
libata 41604 1 ata_piix
scsi_mod 125196 3
usb_storage,sd_mod,libata
unix 28692 18
font 8320 0
vesafb 6656 0
cfbcopyarea 3840 1 vesafb
cfbimgblt 3040 1 vesafb
cfbfillrect 3776 1 vesafb
cardctl status
Socket 0:
no card
Socket 1:
3.3V CardBus card
function 0: [ready]
function 1: [ready]
cardctl info
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
cardctl ident:
Socket 0:
no product info available
Socket 1:
no product info available
___________________________________________________________ALL-NEW Yahoo! Messenger - all new features - even more fun! http://uk.messenger.yahoo.com
Reply to: