[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: FA510c update



On Thu, Mar 01, 2001 at 12:23:16AM +0100, Felix E. Klee wrote:
> "Felix E. Klee" wrote:
> > The error message that I get is
> >   failed to allocate resource 0 for PCI device 1011:0019
> >   got res[10800000:108003ff] for resource 1 of PCI device 1011:0019
> >   got res[10400000:1043ffff] for resource 6 of PCI device 1011:0019
> >   PCI: Enabling device 01:00.0 (0000->0003)
> >   PCI: No IRQ known for interrupt pin A of device 01:00.0. Please try
> > using pci=biosirq.
> 
> BTW, I did try pci=biosirq as a kernel option but this only removed the
Did you actually use "pci=biosirq", or did you use "pci=$your_cards_irq"?

> last line of the error messages.
> 
> I am still open to suggestions.
> 
> Felix

Also, I attempted to locate all my stuff dealing with the card (it's the only card):

>Linux PCMCIA Card Services 3.1.22
>  options:  [pci] [cardbus] [pm]
>PCI: Found IRQ 11 for device 00:0b.0
>PCI: The same IRQ used for device 01:00.0
>PCI: Found IRQ 11 for device 00:0b.1
>PCI: The same IRQ used for device 00:0c.0

::other stuff::

>cs: cb_alloc(bus 20): vendor 0x1011, device 0x0019
>  got res[1000:107f] for resource 0 of PCI device 1011:0019
>  got res[10800000:108003ff] for resource 1 of PCI device 1011:0019
>  got res[10400000:1043ffff] for resource 6 of PCI device 1011:0019
>PCI: Enabling device 14:00.0 (0000 -> 0003)

::other stuff::

>Linux Tulip driver version 0.9.13a (January 20, 2001)
>PCI: Setting latency timer of device 14:00.0 to 64
>eth0: Digital DS21143 Tulip rev 65 at 0x1000, 00:10:7A:15:DA:D6, IRQ 11.
>eth0:  EEPROM default media type Autosense.
>eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
>eth0:  MII transceiver #1 config 1000 status 7869 advertising 01e1.
>eth0: no IPv6 routers present

::other stuff::

>cs: IO port probe 0x0c00-0x0cff: clean.
>cs: IO port probe 0x0800-0x08ff: clean.
>cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
>cs: IO port probe 0x0a00-0x0aff: clean.

I have a Toshiba Sattelite 2775XDVD.  It has two Type 2 PCMCIA/Cardbus slots.  The above message occurs when my eth card (FA510C) is plugged into Slot 0
	--xsdg

-- 
 ___________________________________________________
/ * dpkg ponders: hAS ANYONE SEEN MY cAPSLOCK KEY?  \
\                                                   /
/    http://xsdg.hypermart.net|xsdg@softhome.net    \
\___________________________________________________/



Reply to: