Soundcard.. then no soundcard
Hi,
Knoppix v4.0
My soundcard works fine when booting from the DVD, but is absent and
won't autodetect on a Debian-type install.
In Control Centre I get an "artsmessage", error while initialising
sound driver.
dmesg complained about irqs and suggested using pci=usepirqmask. I did
this, and the boot note went away, but still no audio :-(
dmesg shows it's there, and lspci. See below.
I found an old note, but it doesn't seem to apply any longer:
Q: Why doesn't my sound work?
A: Just run "/etc/init.d/alsa-autoconfig" as root once and you'll be
fixed up nicely. To have the sound levels set at boot (alsa defaults
to muted) edit the file "/etc/init.d/bootmisc.sh" and add aumix -w 75
-v 75 to the bottom of the file.
Best,
Marc
----
0000:00:1e.2 Multimedia audio controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
Subsystem: Acer Incorporated [ALI]: Unknown device 007a
Flags: bus master, medium devsel, latency 0, IRQ 9
I/O ports at e000 [size=256]
I/O ports at e100 [size=64]
Memory at d0000000 (32-bit, non-prefetchable) [size=512]
Memory at d0000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
----
Search for "Intel 810 + AC97 Audio, version 1.01"
Linux version 2.6.12 (root@Knoppix) (gcc-Version 3.3.6 (Debian 1:3.3.6-7)) #2 SMP Tue Aug 9 23:20:52 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffdf000 (usable)
BIOS-e820: 000000001ffe0000 - 000000001fffffc0 (ACPI data)
BIOS-e820: 000000001fffffc0 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131039
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126943 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 INSYDE ) @ 0x000e5010
ACPI: RSDT (v001 INSYDE RSDT_000 0x00000100 ABCD 0x00010200) @ 0x1fff853b
ACPI: FADT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x1ffffac0
ACPI: MADT (v001 STUPID MAPIC_00 0x30307830 ABCD 0x00010200) @ 0x1ffffb50
ACPI: MCFG (v001 INSYDE MCFG_000 0x30303030 0000 0x30303030) @ 0x1ffffbc0
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030522) @ 0x1fff874b
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030522) @ 0x1fff8573
ACPI: DSDT (v001 COMPAL EDL00 0x00000001 INTL 0x02002036) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Allocating PCI resources starting at 20000000 (gap: 20000000:dff00000)
Built 1 zonelists
Kernel command line: root=/dev/hdc6 ro ramdisk_size=100000 lang=en pci=noacpi pci=usepirqmask vga=791
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1596.514 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 510040k/524156k available (1882k kernel code, 13480k reserved, 999k data, 296k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3145.72 BogoMIPS (lpj=1572864)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: setting ELCR to 0e20 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
Total of 1 processors activated (3145.72 BogoMIPS).
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4069k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xea814, last bus=6
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: Embedded Controller [EC0] (gpe 29)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Discovered primary peer bus 04 [IRQ]
PCI: Discovered primary peer bus 05 [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/2641] at 0000:00:1f.0
PCI: Found IRQ 11 for device 0000:00:01.0
PCI: Sharing IRQ 11 with 0000:00:1c.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Sharing IRQ 11 with 0000:06:04.0
PCI: <NULL> IRQ 5 for device 0000:00:1c.1
PCI: Sharing IRQ 5 with 0000:00:1e.2
PCI: Sharing IRQ 5 with 0000:06:04.1
PCI: Sharing IRQ 5 with 0000:06:04.2
PCI: Sharing IRQ 5 with 0000:06:04.3
PCI: Sharing IRQ 5 with 0000:06:04.4
PCI: Found IRQ 11 for device 0000:00:1f.2
PCI: Sharing IRQ 11 with 0000:00:1d.1
PCI: Sharing IRQ 11 with 0000:00:1f.3
PCI: Cannot allocate resource region 3 of device 0000:01:00.0
audit: initializing netlink socket (disabled)
audit(1128284798.711:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: Found IRQ 11 for device 0000:00:01.0
PCI: Sharing IRQ 11 with 0000:00:1c.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Sharing IRQ 11 with 0000:06:04.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
PCI: Found IRQ 11 for device 0000:00:1c.0
PCI: Sharing IRQ 11 with 0000:00:01.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Sharing IRQ 11 with 0000:06:04.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
PCI: setting IRQ 9 as level-triggered
PCI: Assigned IRQ 9 for device 0000:00:1c.1
PCI: Sharing IRQ 9 with 0000:00:1e.2
PCI: Sharing IRQ 9 with 0000:06:04.1
PCI: Sharing IRQ 9 with 0000:06:04.2
PCI: Sharing IRQ 9 with 0000:06:04.3
PCI: Sharing IRQ 9 with 0000:06:04.4
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: framebuffer at 0x90000000, mapped to 0xe0880000, using 3072k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d8d0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: ST9808210A, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 1024KiB
hdc: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
libata version 1.11 loaded.
ahci version 1.00
PCI: Found IRQ 11 for device 0000:00:1f.2
PCI: Sharing IRQ 11 with 0000:00:1d.1
PCI: Sharing IRQ 11 with 0000:00:1f.3
ahci: probe of 0000:00:1f.2 failed with error -12
ata_piix version 1.03
PCI: Found IRQ 11 for device 0000:00:1f.2
PCI: Sharing IRQ 11 with 0000:00:1d.1
PCI: Sharing IRQ 11 with 0000:00:1f.3
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14
ata1: dev 1 cfg 49:0f00 82:421c 83:0000 84:0000 85:0000 86:0000 87:0000 88:0000
ata1: dev 1 ATAPI, max MWDMA2
ata1: dev 1 configured for MWDMA2
scsi0 : ata_piix
Vendor: HL-DT-ST Model: DVDRAM GMA-4080N Rev: 0H39
Type: CD-ROM ANSI SCSI revision: 05
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
spurious 8259A interrupt: IRQ7.
IP: routing cache hash table of 2048 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 7, 524288 bytes)
TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices:
AZAL RP02 RP03 RP04 USB1 USB2 USB3 USB4 USB7 ELAN MODM
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 296k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
EXT3 FS on hdc6, internal journal
ts: Compaq touchscreen protocol output
Adding 4883720k swap on /dev/hdc5. Priority:-1 extents:1
EXT3 FS on hdc6, internal journal
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0: LSR safety check engaged!
ttyS0: LSR safety check engaged!
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdc3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 11 for device 0000:00:1d.0
PCI: Sharing IRQ 11 with 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001200
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.1
PCI: Sharing IRQ 11 with 0000:00:1f.2
PCI: Sharing IRQ 11 with 0000:00:1f.3
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.2
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:00:01.0
PCI: Sharing IRQ 11 with 0000:00:1c.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Sharing IRQ 11 with 0000:06:04.0
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 11, io base 0x00001260
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 10 for device 0000:06:00.0
PCI: Sharing IRQ 10 with 0000:00:1e.3
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[b0020000-b00207ff] Max Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Registering unionfs 20050811-1552
Real Time Clock Driver v1.12
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 0000:06:04.0
PCI: Sharing IRQ 11 with 0000:00:01.0
PCI: Sharing IRQ 11 with 0000:00:1c.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:06:04.0 [1025:007a]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f57714042c4]
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000006
eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
parport0: PC-style at 0x278 (0x678) [PCSPP,TRISTATE]
parport0: irq 14 detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
tg3.c:v3.31 (June 8, 2005)
PCI: Found IRQ 11 for device 0000:06:01.0
eth1: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0f:b0:80:8d:a0
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[763f0000]
NET: Registered protocol family 17
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.1
ipw2200: Copyright(c) 2003-2004 Intel Corporation
PCI: Found IRQ 11 for device 0000:06:02.0
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Intel 810 + AC97 Audio, version 1.01, 22:38:37 Aug 9 2005
PCI: Found IRQ 9 for device 0000:00:1e.2
PCI: Sharing IRQ 9 with 0000:00:1c.1
PCI: Sharing IRQ 9 with 0000:06:04.1
PCI: Sharing IRQ 9 with 0000:06:04.2
PCI: Sharing IRQ 9 with 0000:06:04.3
PCI: Sharing IRQ 9 with 0000:06:04.4
PCI: Setting latency timer of device 0000:00:1e.2 to 64
i810: Intel ICH4 found at IO 0xe100 and 0xe000, MEM 0xd0000000 and 0xd0000200, IRQ 9
i810: Intel ICH4 mmio at 0xe0f50000 and 0xe0f7e200
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: ALG82 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
i810_audio: setting clocking to 48689
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
PCI: Found IRQ 11 for device 0000:00:1d.7
PCI: Sharing IRQ 11 with 0000:00:1d.0
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 11, io mem 0x20000000
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hw_random: cannot enable RNG, aborting
PCI: Found IRQ 10 for device 0000:00:1e.3
PCI: Sharing IRQ 10 with 0000:06:00.0
PCI: Setting latency timer of device 0000:00:1e.3 to 64
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 5
ieee80211_crypt: registered algorithm 'WEP'
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x3b0-0x3df 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
codec_semaphore: semaphore is not ready [0x1][0x701300]
codec_write 1: semaphore is not ready for register 0x54
apm: BIOS not found.
lp0: using parport0 (polling).
lp0: console ready
apm: BIOS not found.
psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
Reply to: