--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-4.19.0-6-amd64: USB3 stops working after resume from disk
- From: Stefan Völkel <bd@bc-bd.org>
- Date: Sat, 18 Jan 2020 16:17:12 +0100
- Message-id: <157936063222.17148.17069814946009709404.reportbug@asrock.bc>
Package: src:linux
Version: 4.19.67-2+deb10u2
Severity: normal
Dear Maintainer,
after a suspend-to-disk / resume cycle the front side USB3 Ports on my ESPRIMO
Q900 no loger work.
FYI, reportbug told me that:
Your version of linux-image-4.19.0-6-amd64 (4.19.67-2+deb10u2) is newer
than that in Debian!
This was a stretch + bpo kernel system upgraded to buster, my guess is that's
the reason for the kernel version.
FWIW the problem did not occur with 4.19.0-5-bpo.
Since reportbug did not capture xhci dmesg entries:
[ 1.764387] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.764395] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 1.869268] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[ 1.869522] usb usb3: Manufacturer: Linux 4.19.0-6-amd64 xhci-hcd
[ 1.869796] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.869800] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[ 1.869804] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 1.872726] usb usb4: Manufacturer: Linux 4.19.0-6-amd64 xhci-hcd
[ 2.208085] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[10548.444992] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[10548.445033] suspend_common(): xhci_pci_suspend+0x0/0xd0 [xhci_pci] returns -110
[10548.445061] pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 [usbcore] returns -110
[10548.445070] dpm_run_callback(): pci_pm_suspend+0x0/0x120 returns -110
[34750.955390] xhci_hcd 0000:02:00.0: Host halt failed, -110
[34750.955395] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset.
[54572.844631] xhci_hcd 0000:02:00.0: Host halt failed, -110
[54572.844635] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset.
[59539.584267] usb 3-1: new full-speed USB device number 2 using xhci_hcd
[59610.253300] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59611.505294] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59611.837250] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59620.369419] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59621.177510] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59622.009529] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59622.473525] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[59959.888692] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[88648.127030] usb 3-1: new full-speed USB device number 3 using xhci_hcd
[92816.651683] xhci_hcd 0000:02:00.0: Host halt failed, -110
[92816.651688] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset.
[92826.757288] xhci_hcd 0000:02:00.0: Abort failed to stop command ring: -110
[92826.773311] xhci_hcd 0000:02:00.0: Host halt failed, -110
[92826.773314] xhci_hcd 0000:02:00.0: xHCI host controller not responding, assume dead
[92826.773321] xhci_hcd 0000:02:00.0: HC died; cleaning up
-- Package-specific info:
** Version:
Linux version 4.19.0-6-amd64 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.67-2+deb10u2 (2019-11-11)
** Command line:
BOOT_IMAGE=/vmlinuz-4.19.0-6-amd64 root=/dev/mapper/sys-root ro quiet resume=/dev/mapper/sys-swap
** Not tainted
** Kernel log:
[168594.181338] video LNXVIDEO:00: Restoring backlight state
[168594.253809] systemd-udevd[11069]: Using default interface naming scheme 'v240'.
[168594.253883] systemd-udevd[11069]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[168594.254045] systemd-udevd[11069]: Could not generate persistent MAC address for br0: No such file or directory
[168594.511159] systemd-udevd[11069]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[168594.512819] br0: port 1(eno1.5) entered blocking state
[168594.512824] br0: port 1(eno1.5) entered disabled state
[168594.513197] device eno1.5 entered promiscuous mode
[168594.516346] device eno1 entered promiscuous mode
[168594.519699] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
[168594.612145] systemd-udevd[11069]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[168594.625137] IPv6: ADDRCONF(NETDEV_UP): eno1.4: link is not ready
[168594.652691] systemd-udevd[11069]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[168594.667904] IPv6: ADDRCONF(NETDEV_UP): eno1.1: link is not ready
[168597.378981] e1000e: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[168597.379222] IPv6: ADDRCONF(NETDEV_CHANGE): eno1.1: link becomes ready
[168597.379355] IPv6: ADDRCONF(NETDEV_CHANGE): eno1.4: link becomes ready
[168597.379512] br0: port 1(eno1.5) entered blocking state
[168597.379516] br0: port 1(eno1.5) entered forwarding state
[168597.379645] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[199199.898231] device eno1 left promiscuous mode
[199199.898447] br0: port 1(eno1.5) entered disabled state
[199199.899670] device eno1.5 left promiscuous mode
[199199.899675] br0: port 1(eno1.5) entered disabled state
[199200.247919] e1000e: eno1 NIC Link is Down
[199200.989031] (NULL device *): firmware: direct-loading firmware iwlwifi-6000g2a-6.ucode
[199201.177803] Syncing filesystems ...
[199201.178085] done.
[199201.178089] Freezing user space processes ... (elapsed 0.002 seconds) done.
[199201.180504] OOM killer disabled.
[199201.180836] PM: Marking nosave pages: [mem 0x00000000-0x00000fff]
[199201.180840] PM: Marking nosave pages: [mem 0x0009a000-0x000fffff]
[199201.180847] PM: Marking nosave pages: [mem 0x20000000-0x201fffff]
[199201.180874] PM: Marking nosave pages: [mem 0x40000000-0x401fffff]
[199201.180901] PM: Marking nosave pages: [mem 0x9e4b9000-0x9e4fbfff]
[199201.180906] PM: Marking nosave pages: [mem 0x9e77f000-0x9e966fff]
[199201.180928] PM: Marking nosave pages: [mem 0x9ebae000-0xffffffff]
[199201.184149] PM: Basic memory bitmaps created
[199201.184668] PM: Preallocating image memory... done (allocated 216050 pages)
[199206.439645] PM: Allocated 864200 kbytes in 5.25 seconds (164.60 MB/s)
[199206.439646] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[199206.441763] Suspending console(s) (use no_console_suspend to debug)
[199206.778822] ACPI: Preparing to enter system sleep state S4
[199206.779380] PM: Saving platform NVS memory
[199206.783984] Disabling non-boot CPUs ...
[199206.809245] smpboot: CPU 1 is now offline
[199206.829614] smpboot: CPU 2 is now offline
[199206.845077] smpboot: CPU 3 is now offline
[199206.845894] PM: Creating hibernation image:
[199207.489265] PM: Need to copy 213751 pages
[199207.489272] PM: Normal pages needed: 213751 + 1024, available pages: 2787119
[199206.847692] PM: Restoring platform NVS memory
[199206.849395] Enabling non-boot CPUs ...
[199206.849487] x86: Booting SMP configuration:
[199206.849490] smpboot: Booting Node 0 Processor 1 APIC 0x2
[199206.852651] cache: parent cpu1 should not be sleeping
[199206.853095] CPU1 is up
[199206.853151] smpboot: Booting Node 0 Processor 2 APIC 0x1
[199206.856351] cache: parent cpu2 should not be sleeping
[199206.857227] CPU2 is up
[199206.857289] smpboot: Booting Node 0 Processor 3 APIC 0x3
[199206.860426] cache: parent cpu3 should not be sleeping
[199206.860954] CPU3 is up
[199206.869741] ACPI: Waking up from system sleep state S4
[199206.938583] usb usb1: root hub lost power or was reset
[199206.938671] usb usb2: root hub lost power or was reset
[199206.942476] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[199206.942564] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[199206.949150] sd 0:0:0:0: [sda] Starting disk
[199207.273935] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[199207.273973] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[199207.276788] ata1.00: configured for UDMA/133
[199207.283078] usb 1-1: reset high-speed USB device number 2 using ehci-pci
[199207.295062] usb 2-1: reset high-speed USB device number 2 using ehci-pci
[199207.307465] ata2.00: configured for UDMA/100
[199207.747094] usb 2-1.4: reset full-speed USB device number 3 using ehci-pci
[199208.063114] usb 2-1.5: reset full-speed USB device number 4 using ehci-pci
[199208.655117] usb 2-1.5.1: reset low-speed USB device number 5 using ehci-pci
[199209.219101] usb 2-1.5.3: reset low-speed USB device number 6 using ehci-pci
[199209.560247] Restarting kernel threads ... done.
[199209.561803] PM: Basic memory bitmaps freed
[199209.561804] OOM killer enabled.
[199209.561805] Restarting tasks ... done.
[199209.562813] video LNXVIDEO:00: Restoring backlight state
[199215.329798] systemd-udevd[15843]: Using default interface naming scheme 'v240'.
[199215.329973] systemd-udevd[15843]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[199215.330282] systemd-udevd[15843]: Could not generate persistent MAC address for br0: No such file or directory
[199216.172245] systemd-udevd[15843]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[199216.172615] br0: port 1(eno1.5) entered blocking state
[199216.172616] br0: port 1(eno1.5) entered disabled state
[199216.172680] device eno1.5 entered promiscuous mode
[199216.174470] device eno1 entered promiscuous mode
[199216.178275] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
[199219.717026] e1000e: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[199219.717246] br0: port 1(eno1.5) entered blocking state
[199219.717248] br0: port 1(eno1.5) entered forwarding state
[199219.717290] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[199223.257266] systemd-udevd[16011]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[199223.257559] systemd-udevd[16011]: Using default interface naming scheme 'v240'.
[199223.512930] systemd-udevd[16011]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
** Model information
sys_vendor: FUJITSU
product_name: ESPRIMO Q900
product_version:
chassis_vendor: AOpen Inc.
chassis_version: MPC-D1009
bios_vendor: American Megatrends Inc.
bios_version: 1.05.1009
board_vendor: AOpen Inc.
board_name: D1009
board_version: A1A3
** Loaded modules:
vhost_net
vhost
tap
tun
nfnetlink_queue
bluetooth
drbg
ansi_cprng
ecdh_generic
nf_conntrack_netlink
algif_skcipher
af_alg
devlink
nft_chain_nat_ipv6
nf_nat_ipv6
ip6t_REJECT
nf_reject_ipv6
nft_chain_nat_ipv4
xt_nat
xt_REDIRECT
ipt_MASQUERADE
nf_nat_ipv4
nf_nat
nfnetlink_log
nft_counter
ipt_REJECT
nf_reject_ipv4
xt_tcpudp
xt_state
xt_conntrack
nf_conntrack
nf_defrag_ipv6
nf_defrag_ipv4
xt_NFLOG
nft_compat
x_tables
nf_tables
nfnetlink
binfmt_misc
autofs4
fuse
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
grace
fscache
sunrpc
bridge
ext4
crc16
mbcache
jbd2
fscrypto
ecb
f71882fg
hwmon_vid
8021q
garp
stp
mrp
llc
loop
parport_pc
ppdev
lp
parport
dm_crypt
snd_usb_audio
intel_rapl
snd_hda_codec_hdmi
snd_usbmidi_lib
snd_rawmidi
snd_hda_codec_realtek
snd_hda_codec_generic
x86_pkg_temp_thermal
intel_powerclamp
snd_hda_intel
snd_hda_codec
snd_hda_core
arc4
coretemp
snd_hwdep
snd_seq_device
iwldvm
snd_pcm
mac80211
kvm_intel
i915
snd_timer
kvm
tpm_infineon
tpm_tis
tpm_tis_core
tpm
mei_wdt
irqbypass
drm_kms_helper
iwlwifi
pcc_cpufreq
sg
snd
crct10dif_pclmul
crc32_pclmul
ghash_clmulni_intel
rng_core
drm
mei_me
mei
pcspkr
i2c_algo_bit
evdev
cfg80211
joydev
iTCO_wdt
wmi
iTCO_vendor_support
button
video
intel_cstate
soundcore
intel_uncore
rfkill
intel_rapl_perf
xfs
dm_mod
raid10
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
hid_generic
usbhid
hid
raid6_pq
libcrc32c
crc32c_generic
raid1
raid0
multipath
linear
md_mod
uas
usb_storage
sr_mod
cdrom
sd_mod
crc32c_intel
ahci
libahci
libata
xhci_pci
xhci_hcd
aesni_intel
ehci_pci
ehci_hcd
aes_x86_64
scsi_mod
crypto_simd
cryptd
glue_helper
i2c_i801
usbcore
e1000e
lpc_ich
usb_common
fan
thermal
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
Subsystem: AOPEN Inc. 2nd Generation Core Processor Family DRAM Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller])
Subsystem: AOPEN Inc. 2nd Generation Core Processor Family Integrated Graphics Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 35
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=512M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family MEI Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 26
Region 0: Memory at f7e2b000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 05)
Subsystem: AOPEN Inc. 82579LM Gigabit Network Connection (Lewisville) [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 36
Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7e29000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7e28000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family High Definition Audio Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at f7e20000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f7d00000-f7dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7e27000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation QM67 Express Chipset Family LPC Controller [8086:1c4f] (rev 05)
Subsystem: AOPEN Inc. QM67 Express Chipset LPC Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family 6 port Mobile SATA AHCI Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7e26000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family SMBus Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7e25000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] [8086:0082] (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN [8086:1301]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 34
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
02:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 03) (prog-if 30 [XHCI])
Subsystem: AOPEN Inc. uPD720200 USB 3.0 Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
** USB devices:
Bus 002 Device 006: ID 045e:077d Microsoft Corp.
Bus 002 Device 005: ID 413c:2011 Dell Computer Corp. Multimedia Pro Keyboard
Bus 002 Device 004: ID 413c:1005 Dell Computer Corp. Multimedia Pro Keyboard Hub
Bus 002 Device 003: ID 413c:a503 Dell Computer Corp.
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 10.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable-debug'), (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.19.0-6-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8), LANGUAGE=en_US:en (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: sysvinit (via /sbin/init)
Versions of packages linux-image-4.19.0-6-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.133+deb10u1
ii kmod 26-1
ii linux-base 4.6
Versions of packages linux-image-4.19.0-6-amd64 recommends:
pn apparmor <none>
ii firmware-linux-free 3.4
Versions of packages linux-image-4.19.0-6-amd64 suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.04~git20190206.bf6db5b4+dfsg1-1
ii grub-pc 2.02+dfsg1-20
pn linux-doc-4.19 <none>
Versions of packages linux-image-4.19.0-6-amd64 is related to:
ii firmware-amd-graphics 20190114-2
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20190114-2
pn firmware-libertas <none>
ii firmware-linux-nonfree 20190114-2
ii firmware-misc-nonfree 20190114-2
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-realtek 20190114-2
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
--- End Message ---