Control: tags -1 + moreinfo
Control: severity -1 important
On Sat, Jan 18, 2025 at 09:16:35AM -0800, Mark Mandel wrote:
> Package: src:linux
> Version: 6.12.9-1
> Severity: critical
> Justification: breaks the whole system
>
> Dear Maintainer,
>
> * What led up to the situation?
> Attempting to boot on the 6.12 Kernel.
>
> * What exactly did you do (or not do) that was effective (or
> ineffective)?
> Booting into 6.12.9 fails every time with a hang (see boot log below that I was able to capture).
> Nothing I could see immeadiately jumps out as an issue in the log however.
>
> Booting into 6.12.6 fails approximately half the time with a hang.
>
> Booting into 6.11.10 only fails rarely.
>
> * What was the outcome of this action?
> Unable to use the system if I can't boot in.
>
> * What outcome did you expect instead?
> Be able to boot into Debian.
>
>
>
> -- Package-specific info:
> ** Kernel log:
>
> 1.3221221 xhci hcd 0000:01:00.2: XHCI Host Controller
> 1.3234491 xhci hcd 0000:01:00.2: new USB bus registered, assigned bus number 3 1.3253941 xhci hcd 0000:01:00.2: hcc params 0x0180ff05 hci version 0x110 quirks 0x0000000000000010
> 1.3268241 xhci Jhcd 0000:01:00.2: XHCI Host Controller
> 1.3281451 xhci_hcd 0000:01:06.2: new USB bus registered, assigned bus number 4
> 1.3294601 xhci Jhcd 0000:01:00.2: Host supports USB 3.1 Enhanced SuperSpeed
> 1.3307851 usb usb3: New USB device found, idVendor 1d6b, idProduct=0002, bcdDevice= 6.12 1.3320811 usb usb3: New USB device strings: Mfr-3, Product 2, SerialNumber=1
> 1.333376] usb usb3: Product: XHCI Host Controller
> 1.3346431 usb usb3: Manufacturer: Linux 6.12.9-amd64 xhci-hcd 1.3358961 usb usb3: SerialNumber: 0000:01:00.2
> 1.3373171 hub 3-0:1.0: USB hub found
> 1.3385571 hub 3-0:1.0: 2 ports detected
> 1.3399371 usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
> 1.341206] usb usb4: New USB device found, idVendor-1d6b, idProduct=0003, bcdDevice= 6.12 1.3424681 usb usb4: New USB device strings: Mfr-3, Product-2, SerialNumber=1
> 1.343729] usb usb4: Product: XHCI Host Controller
> 1.3449831 usb usb4: Manufacturer: Linux 6.12.9-and64 xhci-hcd
> 1.346241] usb usb4: SerialNumber: 0000:01:00.2 1.347586] hub 4-0:1.0: USB hub found
> 1.348833] hub 4-0:1.0: 4 ports detected
> 1.3503981 xhci hcd 0000:43:00.0: XHCI Host Controller 1.3516421 xhcỉ hcd 0000:43:00.0: new USB bus registered, assigned bus number 5
> 1.3540771 xhcỉ hcd 0000:43:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
> 1.355682] xhci_hcd 0000:43:00.0: XHCI Host Controller
> 1.3569361 xhcỉ hcd 0000:43:00.0: new USB bus registered, assigned bus number 6 1.3582841 xhcỉ hcd 0000:43:00.0: Host supports USB 3.1 Enhanced SuperSpeed
> 1.359623] usb usb5: New USB device found, idVendor-1d6b, idProduct=0002, bcdDevice= 6.12 1.360924] usb usb5: New USB device strings: Mfr 3, Product-2, SerialNumber=1
> 1.362199] usb usb5: Product: XHCI Host Controller 1.363454] usb usb5: Manufacturer: Linux 6.12.9-amd64 xhci-hed
> 1.3647263 usb usb5: SerialNumber: 0000:43:00.0
> 1.3660751 hub 5-0:1.0: USB hub found
> 1.3673591 hub 5-0:1.0: 2 ports detected
> 1.3691061 usb usb6: Neu USB device found, idVendor 1d6b, idProduct=0003, bcdDevice 6.12 1.3704031 usb usb6: New USB device strings: Mfr 3, Product-2, SerialNumber=1
> 1.3717111 usb usb6: Product: XHCI Host Controller
> 1.3730183 usb usb6: Manufacturer: Linux 6.12.9-and64 xhci-hod
> 1.374336] usb usb6: SerialNumber: 0000:43:00.0 1.375719] hub 6-0:1.0: USB hub found
> 1.3771061 hub 6-0:1.0: 2 ports detected 1.441039] tsc: Refined TSC clocksource calibration: 3600.000 MHz
> 1.4423371 clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x33e452fbb2f, max_idle_ns: 440795236593 ns
> 1.4437331 clocksource: Suitched to clocksource tsc 1.569138] usb 1-2: new high-speed USB device number 2 using xhci_hcd
> 1.6056501 ata1: SATA link down (SStatus 4 SControl 300)
> 1.6133571 8169 0000:45:00.0 enp69s09: renaned fron ethe
> 1.615278] input: DELL08C4:00 06CB:8495 House as/devices/pc10000:00/0000:00:15.6/12c_designware.0/120-1/12c-DELL08C4:00/0018:06CB:8495.0001/input/input6 1.6167241 hid-generic 0018:06CB:8495.0001: input, hidrauß: 12C HID 01.00 Mouse [DELL08C4:00 06CB:84951 on 120-BELL08C4:00
> 1.7095061 usb 1-2: New USB device found, idVendor 1a40, idProduct=0101, bcdDevice 1.11 1.710872] usb 1-2: New USB device strings: fr-9, Product 1, SerialNumber=0
> 1.7122263 usb 1-2: Product: USB 2.0 Hub
> 1.714519] hub 1-2:1.0: USB hub found
> 1.715979) hub 1-2:1.0: 4 ports detected
> 160442853 rni4 f34 rni4-00.fn34: rni f34u7 probe: Unrecognized bootloader version: 13 ( 1.7456411 rmi4 f34 rai4-00.fn34: probe with driver rm14 134 failed with error -22
> 1.778860] rm14 f01 rm14-00.fn01: found BMI device, manufacturer: Synaptics, product: TM3394-001, fu 14: 2706778 1.8290911 usb 2-5: neu SuperSpeed USB device number 2 using xhaị hoả
> 1.8307701 ish-hid ( 33AECD58-8679-4E54-9809-004034F0C226): (hid-ishli enun devices done OK, nun hid devices-1 1.835597] hid-generic 001F:8087:00C2.0002: hidraud: SENSOR HUB HID 02.00 Device Chid-ishtp 0007:08C2) on
> 1.8389781 hid-sensor-hub 001F:8087:0AC2,0002: hidraud: SENSOR HUB HID 02.00 Device thid-ishtp 0007:0062300 1.8564641 usb 2-5: New USB device found, idVendor-2677, idProduct=3601, bedDevice 0.00
> 1.8579341 usb 2-5: New USB device strings: fr-1, Product-20, Serial Nunber-2
> 1.8594081 usb 2-5: Product: AV.io HD Video
> 1.860885) usb 2-5: Manufacturer: Epiphan Systems Inc, 1.862429] usb 2-5: SerialMunber: 335557
>
> ** Model information
> sys_vendor: Alienware
> product_name: Alienware Area-51m
> product_version: 1.18.0
> chassis_vendor: Alienware
> chassis_version: Not Specified
> bios_vendor: Alienware
> bios_version: 1.18.0
> board_vendor: Alienware
> board_name: Alienware Area-51m
> board_version: A00
>
> ** Network interface configuration:
> *** /etc/network/interfaces:
>
> source /etc/network/interfaces.d/*
>
> auto lo
> iface lo inet loopback
>
> allow-hotplug enp69s0
> iface enp69s0 inet dhcp
> iface enp69s0 inet6 auto
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation 8th/9th Gen Core 8-core Desktop Processor Host Bridge/DRAM Registers [Coffee Lake S] [8086:3e30] (rev 0d)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Latency: 0
> IOMMU group: 1
> Capabilities: <access denied>
> Kernel driver in use: skl_uncore
> Kernel modules: ie31200_edac
>
> 00:01.0 PCI bridge [0604]: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) [8086:1901] (rev 0d) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 122
> IOMMU group: 2
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 5000-5fff [size=4K] [16-bit]
> Memory behind bridge: bc000000-bd0fffff [size=17M] [32-bit]
> Prefetchable memory behind bridge: 90000000-a20fffff [size=289M] [32-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x8) [8086:1905] (rev 0d) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 123
> IOMMU group: 2
> Bus: primary=00, secondary=02, subordinate=09, sec-latency=0
> I/O behind bridge: 4000-4fff [size=4K] [16-bit]
> Memory behind bridge: bd200000-d11fffff [size=320M] [32-bit]
> Prefetchable memory behind bridge: 70000000-83ffffff [size=320M] [32-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:02.0 Display controller [0380]: Intel Corporation CoffeeLake-S GT2 [UHD Graphics 630] [8086:3e98] (rev 02)
> DeviceName: Onboard - Video
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 225
> IOMMU group: 0
> Region 0: Memory at bb000000 (64-bit, non-prefetchable) [size=16M]
> Region 2: Memory at 30000000 (64-bit, prefetchable) [size=256M]
> Region 4: I/O ports at 6000 [size=64]
> Capabilities: <access denied>
> Kernel driver in use: i915
> Kernel modules: i915
>
> 00:04.0 Signal processing controller [1180]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem [8086:1903] (rev 0d)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 3
> Region 0: Memory at d1610000 (64-bit, non-prefetchable) [size=32K]
> Capabilities: <access denied>
> Kernel driver in use: proc_thermal
> Kernel modules: processor_thermal_device_pci_legacy
>
> 00:08.0 System peripheral [0880]: Intel Corporation Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th/8th Gen Core Processor Gaussian Mixture Model [8086:1911]
> DeviceName: Onboard - Other
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 255
> IOMMU group: 4
> Region 0: Memory at d162b000 (64-bit, non-prefetchable) [disabled] [size=4K]
> Capabilities: <access denied>
>
> 00:12.0 Signal processing controller [1180]: Intel Corporation Cannon Lake PCH Thermal Controller [8086:a379] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 5
> Region 0: Memory at d162a000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: intel_pch_thermal
> Kernel modules: intel_pch_thermal
>
> 00:13.0 Serial controller [0700]: Intel Corporation Device [8086:a37c] (rev 10) (prog-if 00 [8250])
> DeviceName: Onboard - Other
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 20
> IOMMU group: 6
> Region 0: Memory at d1620000 (64-bit, non-prefetchable) [size=8K]
> Capabilities: <access denied>
> Kernel driver in use: intel_ish_ipc
> Kernel modules: intel_ish_ipc
>
> 00:14.0 USB controller [0c03]: Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller [8086:a36d] (rev 10) (prog-if 30 [XHCI])
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 183
> IOMMU group: 7
> Region 0: Memory at d1600000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 00:14.2 RAM memory [0500]: Intel Corporation Cannon Lake PCH Shared SRAM [8086:a36f] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> IOMMU group: 7
> Region 0: Memory at d161e000 (64-bit, non-prefetchable) [disabled] [size=8K]
> Region 2: Memory at d1629000 (64-bit, non-prefetchable) [disabled] [size=4K]
> Capabilities: <access denied>
>
> 00:15.0 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #0 [8086:a368] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 8
> Region 0: Memory at 62000000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: intel-lpss
> Kernel modules: intel_lpss_pci
>
> 00:15.1 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #1 [8086:a369] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> IOMMU group: 8
> Region 0: Memory at 62001000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: intel-lpss
> Kernel modules: intel_lpss_pci
>
> 00:16.0 Communication controller [0780]: Intel Corporation Cannon Lake PCH HECI Controller [8086:a360] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 208
> IOMMU group: 9
> Region 0: Memory at d1626000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: mei_me
> Kernel modules: mei_me
>
> 00:17.0 SATA controller [0106]: Intel Corporation Cannon Lake PCH SATA AHCI Controller [8086:a352] (rev 10) (prog-if 01 [AHCI 1.0])
> DeviceName: Onboard - SATA
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 191
> IOMMU group: 10
> Region 0: Memory at d161c000 (32-bit, non-prefetchable) [size=8K]
> Region 1: Memory at d1625000 (32-bit, non-prefetchable) [size=256]
> Region 2: I/O ports at 6090 [size=8]
> Region 3: I/O ports at 6080 [size=4]
> Region 4: I/O ports at 6060 [size=32]
> Region 5: Memory at d1624000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: <access denied>
> Kernel driver in use: ahci
> Kernel modules: ahci
>
> 00:1b.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port #17 [8086:a340] (rev f0) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 124
> IOMMU group: 11
> Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
> I/O behind bridge: [disabled] [16-bit]
> Memory behind bridge: d1500000-d15fffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1b.4 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port #21 [8086:a32c] (rev f0) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 125
> IOMMU group: 12
> Bus: primary=00, secondary=0b, subordinate=43, sec-latency=0
> I/O behind bridge: 7000-8fff [size=8K] [16-bit]
> Memory behind bridge: a4000000-ba0fffff [size=353M] [32-bit]
> Prefetchable memory behind bridge: 40000000-61ffffff [size=544M] [32-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1d.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port #9 [8086:a330] (rev f0) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 126
> IOMMU group: 13
> Bus: primary=00, secondary=44, subordinate=44, sec-latency=0
> I/O behind bridge: [disabled] [16-bit]
> Memory behind bridge: d1400000-d14fffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1d.6 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port #15 [8086:a336] (rev f0) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin C routed to IRQ 127
> IOMMU group: 14
> Bus: primary=00, secondary=45, subordinate=45, sec-latency=0
> I/O behind bridge: 3000-3fff [size=4K] [16-bit]
> Memory behind bridge: d1300000-d13fffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1d.7 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port #16 [8086:a337] (rev f0) (prog-if 00 [Normal decode])
> Subsystem: Intel Corporation Device [8086:7270]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin D routed to IRQ 128
> IOMMU group: 15
> Bus: primary=00, secondary=46, subordinate=46, sec-latency=0
> I/O behind bridge: [disabled] [16-bit]
> Memory behind bridge: d1200000-d12fffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1e.0 Communication controller [0780]: Intel Corporation Cannon Lake PCH Serial IO UART Host Controller [8086:a328] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 20
> IOMMU group: 16
> Region 0: Memory at 62002000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: intel-lpss
> Kernel modules: intel_lpss_pci
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation Z390 Chipset LPC/eSPI Controller [8086:a305] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> IOMMU group: 17
>
> 00:1f.3 Audio device [0403]: Intel Corporation Cannon Lake PCH cAVS [8086:a348] (rev 10)
> DeviceName: Onboard - Sound
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 226
> IOMMU group: 17
> Region 0: Memory at d1618000 (64-bit, non-prefetchable) [size=16K]
> Region 4: Memory at bd100000 (64-bit, non-prefetchable) [size=1M]
> Capabilities: <access denied>
> Kernel driver in use: snd_hda_intel
> Kernel modules: snd_hda_intel, snd_soc_skl, snd_soc_avs, snd_sof_pci_intel_cnl
>
> 00:1f.4 SMBus [0c05]: Intel Corporation Cannon Lake PCH SMBus Controller [8086:a323] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 17
> Region 0: Memory at d1622000 (64-bit, non-prefetchable) [size=256]
> Region 4: I/O ports at efa0 [size=32]
> Kernel driver in use: i801_smbus
> Kernel modules: i2c_i801
>
> 00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH SPI Controller [8086:a324] (rev 10)
> DeviceName: Onboard - Other
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> IOMMU group: 17
> Region 0: Memory at fe010000 (32-bit, non-prefetchable) [size=4K]
>
> 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation TU104BM [GeForce RTX 2080 Mobile] [10de:1ed0] (rev a1) (prog-if 00 [VGA controller])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 227
> IOMMU group: 2
> Region 0: Memory at bc000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at 90000000 (64-bit, prefetchable) [size=256M]
> Region 3: Memory at a0000000 (64-bit, prefetchable) [size=32M]
> Region 5: I/O ports at 5000 [size=128]
> Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
> Capabilities: <access denied>
> Kernel driver in use: nvidia
> Kernel modules: nvidia
>
> 01:00.1 Audio device [0403]: NVIDIA Corporation TU104 HD Audio Controller [10de:10f8] (rev a1)
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> IOMMU group: 2
> Region 0: Memory at bd080000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: snd_hda_intel
> Kernel modules: snd_hda_intel
>
> 01:00.2 USB controller [0c03]: NVIDIA Corporation TU104 USB 3.1 Host Controller [10de:1ad8] (rev a1) (prog-if 30 [XHCI])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin C routed to IRQ 192
> IOMMU group: 2
> Region 0: Memory at a2000000 (64-bit, prefetchable) [size=256K]
> Region 3: Memory at a2040000 (64-bit, prefetchable) [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 01:00.3 Serial bus controller [0c80]: NVIDIA Corporation TU104 USB Type-C UCSI Controller [10de:1ad9] (rev a1)
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin D routed to IRQ 255
> IOMMU group: 2
> Region 0: Memory at bd084000 (32-bit, non-prefetchable) [disabled] [size=4K]
> Capabilities: <access denied>
>
> 0a:00.0 Non-Volatile memory controller [0108]: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983 [144d:a808] (prog-if 02 [NVM Express])
> Subsystem: Samsung Electronics Co Ltd SSD 970 EVO/PRO [144d:a801]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 18
> Region 0: Memory at d1500000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: nvme
> Kernel modules: nvme
>
> 0b:00.0 PCI bridge [0604]: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] [8086:15da] (rev 02) (prog-if 00 [Normal decode])
> Subsystem: Dell Device [1028:08c4]
> Physical Slot: 24
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 19
> Bus: primary=0b, secondary=0c, subordinate=43, sec-latency=0
> I/O behind bridge: 7000-7fff [size=4K] [16-bit]
> Memory behind bridge: a4000000-ba0fffff [size=353M] [32-bit]
> Prefetchable memory behind bridge: 40000000-61ffffff [size=544M] [32-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 0c:00.0 PCI bridge [0604]: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] [8086:15da] (rev 02) (prog-if 00 [Normal decode])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 129
> IOMMU group: 20
> Bus: primary=0c, secondary=0d, subordinate=0d, sec-latency=0
> I/O behind bridge: [disabled] [32-bit]
> Memory behind bridge: ba000000-ba0fffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 0c:01.0 PCI bridge [0604]: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] [8086:15da] (rev 02) (prog-if 00 [Normal decode])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 130
> IOMMU group: 21
> Bus: primary=0c, secondary=0e, subordinate=42, sec-latency=0
> I/O behind bridge: 7000-7fff [size=4K] [16-bit]
> Memory behind bridge: a4000000-b9efffff [size=351M] [32-bit]
> Prefetchable memory behind bridge: 40000000-61ffffff [size=544M] [32-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 0c:02.0 PCI bridge [0604]: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] [8086:15da] (rev 02) (prog-if 00 [Normal decode])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 131
> IOMMU group: 22
> Bus: primary=0c, secondary=43, subordinate=43, sec-latency=0
> I/O behind bridge: [disabled] [32-bit]
> Memory behind bridge: b9f00000-b9ffffff [size=1M] [32-bit]
> Prefetchable memory behind bridge: [disabled] [64-bit]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 0d:00.0 System peripheral [0880]: Intel Corporation JHL6340 Thunderbolt 3 NHI (C step) [Alpine Ridge 2C 2016] [8086:15d9] (rev 02)
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 20
> Region 0: Memory at ba000000 (32-bit, non-prefetchable) [size=256K]
> Region 1: Memory at ba040000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: thunderbolt
> Kernel modules: thunderbolt
>
> 43:00.0 USB controller [0c03]: Intel Corporation JHL6340 Thunderbolt 3 USB 3.1 Controller (C step) [Alpine Ridge 2C 2016] [8086:15db] (rev 02) (prog-if 30 [XHCI])
> Subsystem: Dell Device [1028:08c4]
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 193
> IOMMU group: 22
> Region 0: Memory at b9f00000 (32-bit, non-prefetchable) [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 44:00.0 Non-Volatile memory controller [0108]: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983 [144d:a808] (prog-if 02 [NVM Express])
> Subsystem: Samsung Electronics Co Ltd SSD 970 EVO/PRO [144d:a801]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 23
> Region 0: Memory at d1400000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: nvme
> Kernel modules: nvme
>
> 45:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. Killer E3000 2.5GbE Controller [10ec:3000] (rev 03)
> Subsystem: Dell Device [1028:08c4]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 18
> IOMMU group: 24
> Region 0: I/O ports at 3000 [size=256]
> Region 2: Memory at d1300000 (64-bit, non-prefetchable) [size=64K]
> Region 4: Memory at d1310000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: r8169
> Kernel modules: r8169
>
> 46:00.0 Network controller [0280]: Intel Corporation Wi-Fi 6 AX200 [8086:2723] (rev 1a)
> Subsystem: Rivet Networks Killer Wi-Fi 6 AX1650x (AX200NGW) [1a56:1654]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 19
> IOMMU group: 25
> Region 0: Memory at d1200000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: iwlwifi
> Kernel modules: iwlwifi
>
>
> ** USB devices:
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 001 Device 002: ID 1a40:0101 Terminus Technology Inc. Hub
> Bus 001 Device 003: ID 187c:0550 Alienware Corporation LED controller
> Bus 001 Device 004: ID 0bda:5538 Realtek Semiconductor Corp. Integrated_Webcam_HD
> Bus 001 Device 005: ID 2104:0306 Tobii Technology AB EyeChip
> Bus 001 Device 006: ID 0d62:2a1c Darfon Electronics Corp. Keyboard
> Bus 001 Device 007: ID 8087:0029 Intel Corp. AX200 Bluetooth
> Bus 001 Device 008: ID 1a40:0101 Terminus Technology Inc. Hub
> Bus 001 Device 009: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
> Bus 001 Device 010: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
> Bus 001 Device 011: ID 1532:0203 Razer USA, Ltd BlackWidow Chroma
> Bus 001 Device 012: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
> Bus 001 Device 013: ID 0fd9:006c Elgato Systems GmbH Stream Deck XL
> Bus 001 Device 014: ID 1532:0084 Razer USA, Ltd RZ01-0321 Gaming Mouse [DeathAdder V2]
> Bus 001 Device 015: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
> Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 002 Device 002: ID 2b77:3601 Epiphan Systems Inc. AV.io HD Video
> Bus 002 Device 003: ID 0bda:0411 Realtek Semiconductor Corp. Hub
> Bus 002 Device 004: ID 0bda:0411 Realtek Semiconductor Corp. Hub
> Bus 002 Device 005: ID 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
> Bus 002 Device 006: ID 0bda:0411 Realtek Semiconductor Corp. Hub
> Bus 002 Device 007: ID 0bda:0411 Realtek Semiconductor Corp. Hub
> Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
>
>
> -- System Information:
> Debian Release: trixie/sid
> APT prefers testing
> APT policy: (500, 'testing')
> Architecture: amd64 (x86_64)
>
> Kernel: Linux 6.11.10-amd64 (SMP w/16 CPU threads; PREEMPT)
> Kernel taint flags: TAINT_PROPRIETARY_MODULE, TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE not set
> Shell: /bin/sh linked to /usr/bin/dash
> Init: systemd (via /run/systemd/system)
> LSM: AppArmor: enabled
You have a tainted system with proprietary modules (presumably nvidia
according at least to the devices). Can you please boot without the
prioprietary modules and see if the boot problems persist?
Regards,
Salvatore