Bug#1053991: linux-image-6.1.0-13-amd64: Only one monitor of multi-monitor displaying after upgrade
Package: src:linux
Version: 6.1.55-1
Severity: important
Dear Maintainer,
* What led up to the situation?
Regular apt update.
* What exactly did you do (or not do) that was effective (or ineffective)?
Rebooted system after apt upgrade.
* What was the outcome of this action?
System only displayed on one of two monitors.
* What outcome did you expect instead?
System should display on all monitors.
* What I tried
Rebooted and selected previous version (6.1.52-1 = linux-
image-6.1.0-12-amd64).
System displayed on both monitors as usual.
* Info: Graphics card: AMD Radeon Pro WX3100. It has three display ports, I
use two of them.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: Dell Inc.
product_name: OptiPlex 5040
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: 1.22.0
board_vendor: Dell Inc.
board_name: 0T7D40
board_version: A01
** Network interface configuration:
*** /etc/network/interfaces:
source /etc/network/interfaces.d/*
auto lo
iface lo inet loopback
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers [8086:191f] (rev 07)
Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers [1028:06ba]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 0
Capabilities: <access denied>
Kernel driver in use: skl_uncore
Kernel modules: ie31200_edac
00:01.0 PCI bridge [0604]: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) [8086:1901] (rev 07) (prog-if 00 [Normal decode])
Subsystem: Dell 6th-10th Gen Core Processor PCIe Controller (x16) [1028:06ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 121
IOMMU group: 1
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: e000-efff [size=4K] [16-bit]
Memory behind bridge: f7e00000-f7efffff [size=1M] [32-bit]
Prefetchable memory behind bridge: e0000000-f01fffff [size=258M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:14.0 USB controller [0c03]: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [8086:a12f] (rev 31) (prog-if 30 [XHCI])
Subsystem: Dell 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [1028:06ba]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 124
IOMMU group: 2
Region 0: Memory at f7f30000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:14.2 Signal processing controller [1180]: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem [8086:a131] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Thermal Subsystem [1028:06ba]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
IOMMU group: 2
Region 0: Memory at f7f4f000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal
00:16.0 Communication controller [0780]: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 [8086:a13a] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family MEI Controller [1028:06ba]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 131
IOMMU group: 3
Region 0: Memory at f7f4e000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:16.3 Serial controller [0700]: Intel Corporation 100 Series/C230 Series Chipset Family KT Redirection [8086:a13d] (rev 31) (prog-if 02 [16550])
Subsystem: Dell 100 Series/C230 Series Chipset Family KT Redirection [1028:06ba]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin D routed to IRQ 19
IOMMU group: 3
Region 0: I/O ports at f060 [size=8]
Region 1: Memory at f7f4d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:17.0 SATA controller [0106]: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [8086:a102] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [1028:06ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 125
IOMMU group: 4
Region 0: Memory at f7f48000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at f7f4c000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at f7f4b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1b.0 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #17 [8086:a167] (rev f1) (prog-if 00 [Normal decode])
Subsystem: Dell 100 Series/C230 Series Chipset Family PCI Express Root Port [1028:06ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
IOMMU group: 5
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: f7d00000-f7dfffff [size=1M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge [0601]: Intel Corporation Q170 Chipset LPC/eSPI Controller [8086:a146] (rev 31)
Subsystem: Dell Q170 Chipset LPC/eSPI Controller [1028:06ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 6
00:1f.2 Memory controller [0580]: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller [8086:a121] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Power Management Controller [1028:06ba]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
IOMMU group: 6
Region 0: Memory at f7f44000 (32-bit, non-prefetchable) [disabled] [size=16K]
00:1f.3 Audio device [0403]: Intel Corporation 100 Series/C230 Series Chipset Family HD Audio Controller [8086:a170] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family HD Audio Controller [1028:06ba]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 132
IOMMU group: 6
Region 0: Memory at f7f40000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at f7f20000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.4 SMBus [0c05]: Intel Corporation 100 Series/C230 Series Chipset Family SMBus [8086:a123] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family SMBus [1028:06ba]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
IOMMU group: 6
Region 0: Memory at f7f4a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2) I219-V [8086:15b8] (rev 31)
Subsystem: Dell Ethernet Connection (2) I219-V [1028:06ba]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 123
IOMMU group: 7
Region 0: Memory at f7f00000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Lexa XT [Radeon PRO WX 3100] [1002:6985] (prog-if 00 [VGA controller])
Subsystem: Dell Lexa XT [Radeon PRO WX 3100] [1028:0b0c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
IOMMU group: 1
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at f0000000 (64-bit, prefetchable) [size=2M]
Region 4: I/O ports at e000 [disabled] [size=256]
Region 5: Memory at f7e00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: amdgpu
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Baffin HDMI/DP Audio [Radeon RX 550 640SP / RX 560/560X] [1002:aae0]
Subsystem: Dell Baffin HDMI/DP Audio [Radeon RX 550 640SP / RX 560/560X] [1028:aae0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 133
IOMMU group: 1
Region 0: Memory at f7e60000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
02:00.0 Non-Volatile memory controller [0108]: Micron/Crucial Technology P2 NVMe PCIe SSD [c0a9:540a] (rev 01) (prog-if 02 [NVM Express])
Subsystem: Micron/Crucial Technology P2 NVMe PCIe SSD [c0a9:540a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
NUMA node: 0
IOMMU group: 8
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 413c:301a Dell Computer Corp. Dell MS116 Optical Mouse
Bus 001 Device 004: ID 0c45:636d Microdia PC-LM1E
Bus 001 Device 003: ID 0930:6544 Toshiba Corp. TransMemory-Mini / Kingston DataTraveler 2.0 Stick
Bus 001 Device 002: ID 046d:c214 Logitech, Inc. ATK3 (Attack III Joystick)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 12.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 6.1.0-13-rt-amd64 (SMP w/4 CPU threads; PREEMPT)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8), LANGUAGE=en_GB:en
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-6.1.0-13-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.142
ii kmod 30+20221128-1
ii linux-base 4.9
Versions of packages linux-image-6.1.0-13-amd64 recommends:
ii apparmor 3.0.8-3
ii firmware-linux-free 20200122-1
Versions of packages linux-image-6.1.0-13-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-efi-amd64 2.06-13+deb12u1
pn linux-doc-6.1 <none>
Versions of packages linux-image-6.1.0-13-amd64 is related to:
ii firmware-amd-graphics 20230210-5
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
ii firmware-misc-nonfree 20230210-5
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: