--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.7-trunk-686-pae: auto remount after umount with some HDD in USB3
- From: gpe92 <gpe92@free.fr>
- Date: Sat, 16 Feb 2013 15:29:03 +0100
- Message-id: <20130216142903.10973.61686.reportbug@reveillon.gpe.org>
Package: src:linux
Version: 3.7.8-1~experimental.1
Severity: important
Dear Maintainer,
I've an external HDD (WD Elements) connecting in USB3, when I
disconnet it in Gnome 3 ("Retirer le volume sans risque"), the disk is
unmounted but immediatly remounted ...
If I connected this HDD on USB2 there is no problem.
With an another HDD in USB3 (WD My Passport), there is no problem.
Here're dmesg reports:
[ 1518.232023] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 1518.244872] usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 1518.245504] usb 3-1: New USB device found, idVendor=1058, idProduct=1042
[ 1518.245510] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1518.245513] usb 3-1: Product: Elements 1042
[ 1518.245516] usb 3-1: Manufacturer: Western Digital
[ 1518.245519] usb 3-1: SerialNumber: 57584E314335323238323934
[ 1518.247138] scsi12 : usb-storage 3-1:1.0
[ 1519.244003] scsi 12:0:0:0: Direct-Access WD Elements 1042 1007 PQ: 0 ANSI: 6
[ 1519.245406] sd 12:0:0:0: Attached scsi generic sg8 type 0
[ 1519.246929] sd 12:0:0:0: [sdh] Spinning up disk...
[ 1520.246677] .......ready
[ 1526.265608] sd 12:0:0:0: [sdh] 976769024 512-byte logical blocks: (500 GB/465 GiB)
[ 1526.266212] sd 12:0:0:0: [sdh] Write Protect is off
[ 1526.266219] sd 12:0:0:0: [sdh] Mode Sense: 47 00 10 08
[ 1526.266671] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.266677] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.268101] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.268107] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.278456] sdh: sdh1
[ 1526.280273] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.280279] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.280282] sd 12:0:0:0: [sdh] Attached SCSI disk
[ 1596.946019] nautilus: sending ioctl 2285 to a partition!
[ 1600.071015] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 3 with no TDs queued?
[ 1600.071090] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 2 with no TDs queued?
[ 1600.071170] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
[ 1600.181741] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
[ 1620.162221] xhci_hcd 0000:07:00.0: Timeout while waiting for stop endpoint command
[ 1620.202225] usb 3-1: USB disconnect, device number 2
Regards.
-- Package-specific info:
** Version:
Linux version 3.7-trunk-686-pae (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Debian 3.7.8-1~experimental.1
** Command line:
BOOT_IMAGE=/vmlinuz-3.7-trunk-686-pae root=UUID=e80aa639-c277-4f03-af6c-7191a2f95083 ro quiet pci=routeirq
** Tainted: PDO (4225)
* Proprietary module has been loaded.
* Kernel has oopsed before.
* Out-of-tree module has been loaded.
** Kernel log:
[ 35.039431] 9:3:1: cannot get freq at ep 0x84
[ 35.061438] 9:3:1: cannot get freq at ep 0x84
[ 37.988226] ttyS1: LSR safety check engaged!
[ 37.988253] ttyS0: LSR safety check engaged!
[ 37.988566] ttyS1: LSR safety check engaged!
[ 37.988593] ttyS0: LSR safety check engaged!
[ 37.988823] ttyS1: LSR safety check engaged!
[ 37.988847] ttyS0: LSR safety check engaged!
[ 928.455203] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 1023.887549] vboxdrv: Found 4 processor cores.
[ 1023.887724] BUG: unable to handle kernel NULL pointer dereference at 00000700
[ 1023.887727] IP: [<f8baa58a>] VBoxHost_RTR0MemObjFree+0x294/0x294 [vboxdrv]
[ 1023.887746] *pdpt = 0000000027d58001 *pde = 0000000000000000
[ 1023.887748] Oops: 0000 [#1] SMP
[ 1023.887750] Modules linked in: vboxdrv(O+) ip6table_filter ip6_tables cpufreq_powersave parport_pc cpufreq_conservative ppdev lp cpufreq_userspace parport cpufreq_stats rfcomm bnep bluetooth ipt_ULOG ipt_REJECT xt_state nf_conntrack_irc nf_conntrack_ftp xt_tcpudp iptable_mangle iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_filter ip_tables x_tables binfmt_misc uinput deflate zlib_deflate ctr twofish_generic twofish_i586 twofish_common camellia_generic serpent_sse2_i586 serpent_generic glue_helper blowfish_generic blowfish_common cast5_generic des_generic cbc xcbc rmd160 sha512_generic sha256_generic sha1_generic hmac crypto_null af_key xfrm_algo fuse nfsd auth_rpcgss nfs_acl nfs lockd dns_resolver fscache sunrpc uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core snd_usb_audio videodev media snd_usbmidi_lib snd_hda_codec_hdmi usb_storage snd_hda_codec_realtek coretemp kvm_intel joydev kvm usbhid hid snd_hda_intel crc32c_intel n
vidia(PO) snd_hda_codec snd_hwdep wacom snd_pcm_oss eeepc_wmi snd_mixer_oss aesni_intel asus_wmi iTCO_wdt sparse_keymap aes_i586 iTCO_vendor_support rfkill snd_pcm xts lrw mxm_wmi gf128mul snd_page_alloc ablk_helper snd_seq_midi cryptd usblp snd_seq_midi_event snd_rawmidi snd_seq evdev snd_seq_device psmouse snd_timer pcspkr serio_raw mei i2c_i801 lpc_ich mfd_core snd i2c_core video soundcore acpi_cpufreq mperf wmi processor button ext4 crc16 jbd2 mbcache dm_mirror dm_region_hash dm_log dm_mod sg sd_mod sr_mod crc_t10dif cdrom firewire_ohci firewire_core ata_generic crc_itu_t thermal fan r8169 mii thermal_sys xhci_hcd pata_marvell ahci libahci ehci_hcd microcode libata scsi_mod usbcore usb_common
[ 1023.887803] Pid: 10471, comm: modprobe Tainted: P O 3.7-trunk-686-pae #1 Debian 3.7.8-1~experimental.1 System manufacturer System Product Name/P8P67 LE
[ 1023.887804] EIP: 0060:[<f8baa58a>] EFLAGS: 00010293 CPU: 2
[ 1023.887817] EIP is at VBoxHost_RTR0MemObjGetPagePhysAddr+0x0/0x67 [vboxdrv]
[ 1023.887818] EAX: f70cd000 EBX: f8bc6a80 ECX: 370cd000 EDX: 00000002
[ 1023.887819] ESI: f70cd000 EDI: 00000700 EBP: 00000000 ESP: e7e5de84
[ 1023.887821] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 1023.887822] CR0: 80050033 CR2: 00000700 CR3: 2fa14000 CR4: 000407f0
[ 1023.887823] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 1023.887824] DR6: ffff0ff0 DR7: 00000400
[ 1023.887825] Process modprobe (pid: 10471, ti=e7e5c000 task=ea972200 task.ti=e7e5c000)
[ 1023.887826] Stack:
[ 1023.887827] f8ba3112 eaa5ef50 00000000 eaa5ef50 00000020 00000246 f8baaf2f 00000000
[ 1023.887830] 00000010 e7e5decc 00000020 f8baaf2f 00000004 00000002 00001000 00018a0e
[ 1023.887833] f8b60000 f8ba9757 ef837780 f8ba978a f8bad4ce 00000010 f8bc02b7 00000000
[ 1023.887836] Call Trace:
[ 1023.887858] [<f8ba3112>] ? supdrvInitDevExt+0x103/0x697 [vboxdrv]
[ 1023.887870] [<f8baaf2f>] ? rtR0MemAllocEx+0x69/0xbc [vboxdrv]
[ 1023.887880] [<f8baaf2f>] ? rtR0MemAllocEx+0x69/0xbc [vboxdrv]
[ 1023.887884] [<f8b60000>] ? 0xf8b5ffff
[ 1023.887903] [<f8ba9757>] ? rtR0MemAlloc+0x8/0x15 [vboxdrv]
[ 1023.887914] [<f8ba978a>] ? VBoxHost_RTMemAllocTag+0xb/0x18 [vboxdrv]
[ 1023.887936] [<f8bad4ce>] ? VBoxHost_RTSpinlockCreate+0x1b/0x4f [vboxdrv]
[ 1023.887949] [<f8baaca7>] ? rtR0PowerNotificationInit+0x11/0x15 [vboxdrv]
[ 1023.887953] [<f8b60000>] ? 0xf8b5ffff
[ 1023.887969] [<f8b60050>] ? VBoxDrvLinuxInit+0x50/0x1000 [vboxdrv]
[ 1023.887972] [<f8b60000>] ? 0xf8b5ffff
[ 1023.887976] [<c100309b>] ? do_one_initcall+0x66/0x10b
[ 1023.887979] [<f8b60000>] ? 0xf8b5ffff
[ 1023.887983] [<c1070147>] ? sys_init_module+0x1504/0x16e4
[ 1023.887996] [<c12ed18d>] ? sysenter_do_call+0x12/0x28
[ 1023.887997] Code: fe ff ff e9 cf fe ff ff 8b 4a 1c 85 c9 0f 84 47 ff ff ff 8d 34 8d fc ff ff ff 89 4c 24 04 e9 5c ff ff ff 83 c4 08 5b 5e 5f 5d c3 <8b> 0f 8b 47 04 8d 91 00 10 00 00 81 fa ff 1f 00 00 76 45 81 39
[ 1023.888016] EIP: [<f8baa58a>] VBoxHost_RTR0MemObjGetPagePhysAddr+0x0/0x67 [vboxdrv] SS:ESP 0068:e7e5de84
[ 1023.888030] CR2: 0000000000000700
[ 1023.888032] ---[ end trace 1c99dea794b154a4 ]---
[ 1518.232023] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 1518.244872] usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 1518.245504] usb 3-1: New USB device found, idVendor=1058, idProduct=1042
[ 1518.245510] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1518.245513] usb 3-1: Product: Elements 1042
[ 1518.245516] usb 3-1: Manufacturer: Western Digital
[ 1518.245519] usb 3-1: SerialNumber: 57584E314335323238323934
[ 1518.247138] scsi12 : usb-storage 3-1:1.0
[ 1519.244003] scsi 12:0:0:0: Direct-Access WD Elements 1042 1007 PQ: 0 ANSI: 6
[ 1519.245406] sd 12:0:0:0: Attached scsi generic sg8 type 0
[ 1519.246929] sd 12:0:0:0: [sdh] Spinning up disk...
[ 1520.246677] .......ready
[ 1526.265608] sd 12:0:0:0: [sdh] 976769024 512-byte logical blocks: (500 GB/465 GiB)
[ 1526.266212] sd 12:0:0:0: [sdh] Write Protect is off
[ 1526.266219] sd 12:0:0:0: [sdh] Mode Sense: 47 00 10 08
[ 1526.266671] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.266677] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.268101] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.268107] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.278456] sdh: sdh1
[ 1526.280273] sd 12:0:0:0: [sdh] No Caching mode page present
[ 1526.280279] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 1526.280282] sd 12:0:0:0: [sdh] Attached SCSI disk
[ 1596.946019] nautilus: sending ioctl 2285 to a partition!
[ 1600.071015] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 3 with no TDs queued?
[ 1600.071090] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 2 with no TDs queued?
[ 1600.071170] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
[ 1600.181741] xhci_hcd 0000:07:00.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
[ 1620.162221] xhci_hcd 0000:07:00.0: Timeout while waiting for stop endpoint command
[ 1620.202225] usb 3-1: USB disconnect, device number 2
[ 1620.573350] usb 3-1: new SuperSpeed USB device number 3 using xhci_hcd
[ 1620.586134] usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 1620.586732] usb 3-1: New USB device found, idVendor=1058, idProduct=1042
[ 1620.586737] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1620.586740] usb 3-1: Product: Elements 1042
[ 1620.586743] usb 3-1: Manufacturer: Western Digital
[ 1620.586745] usb 3-1: SerialNumber: 57584E314335323238323934
[ 1620.588283] scsi13 : usb-storage 3-1:1.0
[ 1621.585317] scsi 13:0:0:0: Direct-Access WD Elements 1042 1007 PQ: 0 ANSI: 6
[ 1621.586775] sd 13:0:0:0: Attached scsi generic sg8 type 0
[ 1621.587110] sd 13:0:0:0: [sdh] 976769024 512-byte logical blocks: (500 GB/465 GiB)
[ 1621.587543] sd 13:0:0:0: [sdh] Write Protect is off
[ 1621.587548] sd 13:0:0:0: [sdh] Mode Sense: 47 00 10 08
[ 1621.587976] sd 13:0:0:0: [sdh] No Caching mode page present
[ 1621.587982] sd 13:0:0:0: [sdh] Assuming drive cache: write through
[ 1621.589274] sd 13:0:0:0: [sdh] No Caching mode page present
[ 1621.589280] sd 13:0:0:0: [sdh] Assuming drive cache: write through
[ 1628.554929] sdh: sdh1
[ 1628.557065] sd 13:0:0:0: [sdh] No Caching mode page present
[ 1628.557071] sd 13:0:0:0: [sdh] Assuming drive cache: write through
[ 1628.557075] sd 13:0:0:0: [sdh] Attached SCSI disk
** Model information
not available
** Loaded modules:
vboxdrv(O+)
ip6table_filter
ip6_tables
cpufreq_powersave
parport_pc
cpufreq_conservative
ppdev
lp
cpufreq_userspace
parport
cpufreq_stats
rfcomm
bnep
bluetooth
ipt_ULOG
ipt_REJECT
xt_state
nf_conntrack_irc
nf_conntrack_ftp
xt_tcpudp
iptable_mangle
iptable_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_nat_ipv4
nf_nat
nf_conntrack
iptable_filter
ip_tables
x_tables
binfmt_misc
uinput
deflate
zlib_deflate
ctr
twofish_generic
twofish_i586
twofish_common
camellia_generic
serpent_sse2_i586
serpent_generic
glue_helper
blowfish_generic
blowfish_common
cast5_generic
des_generic
cbc
xcbc
rmd160
sha512_generic
sha256_generic
sha1_generic
hmac
crypto_null
af_key
xfrm_algo
fuse
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
snd_usb_audio
videodev
media
snd_usbmidi_lib
snd_hda_codec_hdmi
usb_storage
snd_hda_codec_realtek
coretemp
kvm_intel
joydev
kvm
usbhid
hid
snd_hda_intel
crc32c_intel
nvidia(PO)
snd_hda_codec
snd_hwdep
wacom
snd_pcm_oss
eeepc_wmi
snd_mixer_oss
aesni_intel
asus_wmi
iTCO_wdt
sparse_keymap
aes_i586
iTCO_vendor_support
rfkill
snd_pcm
xts
lrw
mxm_wmi
gf128mul
snd_page_alloc
ablk_helper
snd_seq_midi
cryptd
usblp
snd_seq_midi_event
snd_rawmidi
snd_seq
evdev
snd_seq_device
psmouse
snd_timer
pcspkr
serio_raw
mei
i2c_i801
lpc_ich
mfd_core
snd
i2c_core
video
soundcore
acpi_cpufreq
mperf
wmi
processor
button
ext4
crc16
jbd2
mbcache
dm_mirror
dm_region_hash
dm_log
dm_mod
sg
sd_mod
sr_mod
crc_t10dif
cdrom
firewire_ohci
firewire_core
ata_generic
crc_itu_t
thermal
fan
r8169
mii
thermal_sys
xhci_hcd
pata_marvell
ahci
libahci
ehci_hcd
microcode
libata
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f6000000-f70fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at f740b000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7408000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: ASUSTeK Computer Inc. Device [1043:841b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at f7400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e0100000-e02fffff
Prefetchable memory behind bridge: 00000000e0300000-00000000e04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev b5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7300000-f73fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Prefetchable memory behind bridge: 00000000f2100000-00000000f21fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.6 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 [8086:1c1c] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f7200000-f72fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Memory behind bridge: f7100000-f71fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7407000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation P67 Express Chipset Family LPC Controller [8086:1c46] (rev 05)
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 47
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at f7406000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:844d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7405000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108 [GeForce GT 430] [10de:0de1] (rev a1) (prog-if 00 [VGA controller])
Subsystem: CardExpert Technology Device [10b0:1401]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
[virtual] Expansion ROM at f7000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
01:00.1 Audio device [0403]: NVIDIA Corporation GF108 High Definition Audio Controller [10de:0bea] (rev a1)
Subsystem: CardExpert Technology Device [10b0:1401]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f7080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
03:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge [1b21:1080] (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=03, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7300000-f73fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
04:03.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. M4A series motherboard [1043:81fe]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f7300000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at d000 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: I/O ports at c000 [size=256]
Region 2: Memory at f2104000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f2100000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
06:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9120 SATA 6Gb/s Controller [1b4b:9120] (rev 12) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: I/O ports at b090 [size=8]
Region 1: I/O ports at b080 [size=4]
Region 2: I/O ports at b070 [size=8]
Region 3: I/O ports at b060 [size=4]
Region 4: I/O ports at b050 [size=16]
Region 5: Memory at f7215000 (32-bit, non-prefetchable) [size=2K]
Expansion ROM at f7200000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
06:00.1 IDE interface [0101]: Marvell Technology Group Ltd. 88SE9128 IDE Controller [1b4b:91a4] (rev 12) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Marvell Technology Group Ltd. 88SE9128 IDE Controller [1b4b:91a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at b040 [size=8]
Region 1: I/O ports at b030 [size=4]
Region 2: I/O ports at b020 [size=8]
Region 3: I/O ports at b010 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at f7214000 (32-bit, non-prefetchable) [size=16]
Expansion ROM at f7210000 [disabled] [size=16K]
Capabilities: <access denied>
Kernel driver in use: pata_marvell
07:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller [1b21:1042] (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8488]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f7100000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
** USB devices:
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 003: ID 1058:1042 Western Digital Technologies, Inc.
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 003: ID 03f0:6104 Hewlett-Packard DeskJet 5650c
Bus 004 Device 004: ID 056a:0011 Wacom Co., Ltd Graphire 2 4x5
Bus 004 Device 005: ID 04b8:0116 Seiko Epson Corp. Perfection 3170 (GT-9400)
Bus 004 Device 006: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 004 Device 007: ID 11b0:6148 ATECH FLASH TECHNOLOGY
Bus 004 Device 008: ID 0424:2640 Standard Microsystems Corp. USB 2.0 Hub
Bus 004 Device 009: ID 0471:0331 Philips (or NXP) SPC 1300NC PC Camera
Bus 004 Device 010: ID 0424:4060 Standard Microsystems Corp. Ultra Fast Media Reader
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.7-trunk-686-pae (SMP w/4 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.7-trunk-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.7-trunk-686-pae recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.13-37
Versions of packages linux-image-3.7-trunk-686-pae suggests:
pn debian-kernel-handbook <none>
ii extlinux 2:4.05+dfsg-6+deb7u1
ii grub-pc 1.99-26
pn linux-doc-3.7 <none>
Versions of packages linux-image-3.7-trunk-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.36+wheezy.1
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.36+wheezy.1
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.7-trunk-686-pae/postinst/depmod-error-initrd-3.7-trunk-686-pae: false
* linux-image-3.7-trunk-686-pae/postinst/missing-firmware-3.7-trunk-686-pae:
linux-image-3.7-trunk-686-pae/postinst/ignoring-ramdisk:
linux-image-3.7-trunk-686-pae/prerm/removing-running-kernel-3.7-trunk-686-pae: true
--- End Message ---