--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: ohci-pci: frame counter not updating
- From: Mike Edwards <pf-debian-bugs@mirkwood.net>
- Date: Sat, 13 May 2017 15:34:27 -0400
- Message-id: <149470406798.8595.413511137489986746.reportbug@balrog0.mirkwood.net>
Package: src:linux
Version: 4.9.18-1
Severity: important
When connecting a device (mini-box 256x64 picoLCD, listed in the kernel log as
'ITUNER INC USB-LCD-256x64') to one of the USB2 ports on this machine, it'll
run fine for up to several hours, and then disconnect, leaving the following
in the kernel log:
ohci-pci 0000:00:12.0: frame counter not updating; disabled
ohci-pci 0000:00:12.0: HC died; cleaning up
Note that in the log below, it managed to run for slightly over 2 minutes after
system boot before dying.
Connecting the device to a USB3 port, causing it to use xhci_hcd, appears to
work reliably.
I've seen similar bug reports for this issue on Ubuntu (I'm running Debian
stretch here):
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1634737
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1635012
The above cases appear to have been resolved by https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a8006bd915095c40098bfcb684cc2bdfb414dc0d
- however, I've verified that the changes introduced by this patch are already
applied to linux-image-4.9.0-2-amd64 ver 4.9.18-1.
My previous installation on here was wheezy, using a backported kernel from jessie.
This USB2 issue did not appear while wheezy was running.
-- Package-specific info:
** Version:
Linux version 4.9.0-2-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170321 (Debian 6.3.0-11) ) #1 SMP Debian 4.9.18-1 (2017-03-30)
** Command line:
placeholder root=/dev/mapper/balrog-root--stretch ro net.ifnames=0 biosdevname=0 quiet
** Not tainted
** Kernel log:
[ 46.674217] lan0: port 1(eth0.2) entered blocking state
[ 46.674219] lan0: port 1(eth0.2) entered disabled state
[ 46.674298] device eth0.2 entered promiscuous mode
[ 46.680647] lan0: port 1(eth0.2) entered blocking state
[ 46.680649] lan0: port 1(eth0.2) entered forwarding state
[ 47.732359] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 47.732367] NFSD: starting 90-second grace period (net ffffffff81cd3980)
[ 48.110022] xen:xen_evtchn: Event-channel device installed
[ 57.821269] lan0: port 2(vif1.0) entered blocking state
[ 57.821271] lan0: port 2(vif1.0) entered disabled state
[ 57.821379] device vif1.0 entered promiscuous mode
[ 57.824143] IPv6: ADDRCONF(NETDEV_UP): vif1.0: link is not ready
[ 57.937745] Bridge firewalling registered
[ 59.756110] xen-blkback: backend/vbd/1/51713: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[ 59.768037] xen-blkback: backend/vbd/1/51714: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[ 59.777334] xen-blkback: backend/vbd/1/51729: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[ 59.796475] xen-blkback: backend/vbd/1/51745: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[ 59.809462] xen-blkback: backend/vbd/1/51761: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[ 59.836503] vif vif-1-0 vif1.0: Guest Rx ready
[ 59.836580] IPv6: ADDRCONF(NETDEV_CHANGE): vif1.0: link becomes ready
[ 59.836627] lan0: port 2(vif1.0) entered blocking state
[ 59.836629] lan0: port 2(vif1.0) entered forwarding state
[ 65.697886] device vif2.0 entered promiscuous mode
[ 65.700755] IPv6: ADDRCONF(NETDEV_UP): vif2.0: link is not ready
[ 67.374042] vif vif-2-0 vif2.0: Guest Rx ready
[ 67.374116] IPv6: ADDRCONF(NETDEV_CHANGE): vif2.0: link becomes ready
[ 67.374717] xen-blkback: backend/vbd/2/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 68.871065] lan0: port 3(vif3.0) entered blocking state
[ 68.871069] lan0: port 3(vif3.0) entered disabled state
[ 68.871236] device vif3.0 entered promiscuous mode
[ 68.875165] IPv6: ADDRCONF(NETDEV_UP): vif3.0: link is not ready
[ 69.290501] xen-blkback: backend/vbd/3/51713: using 1 queues, protocol 1 (x86_64-abi)
[ 69.308346] xen-blkback: backend/vbd/3/51714: using 1 queues, protocol 1 (x86_64-abi)
[ 69.337093] vif vif-3-0 vif3.0: Guest Rx ready
[ 69.337170] IPv6: ADDRCONF(NETDEV_CHANGE): vif3.0: link becomes ready
[ 69.337225] lan0: port 3(vif3.0) entered blocking state
[ 69.337226] lan0: port 3(vif3.0) entered forwarding state
[ 72.396111] GuestNet: port 2(vif4.0) entered blocking state
[ 72.396113] GuestNet: port 2(vif4.0) entered disabled state
[ 72.396227] device vif4.0 entered promiscuous mode
[ 72.399081] IPv6: ADDRCONF(NETDEV_UP): vif4.0: link is not ready
[ 74.197440] xen-blkback: backend/vbd/4/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 74.225330] vif vif-4-0 vif4.0: Guest Rx ready
[ 74.225383] IPv6: ADDRCONF(NETDEV_CHANGE): vif4.0: link becomes ready
[ 74.225430] GuestNet: port 2(vif4.0) entered blocking state
[ 74.225432] GuestNet: port 2(vif4.0) entered forwarding state
[ 76.183978] lan0: port 4(vif5.0) entered blocking state
[ 76.183980] lan0: port 4(vif5.0) entered disabled state
[ 76.184089] device vif5.0 entered promiscuous mode
[ 76.186851] IPv6: ADDRCONF(NETDEV_UP): vif5.0: link is not ready
[ 77.858265] xen-blkback: backend/vbd/5/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 77.880994] xen-blkback: backend/vbd/5/51714: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 77.914863] vif vif-5-0 vif5.0: Guest Rx ready
[ 77.914935] IPv6: ADDRCONF(NETDEV_CHANGE): vif5.0: link becomes ready
[ 77.914999] lan0: port 4(vif5.0) entered blocking state
[ 77.915001] lan0: port 4(vif5.0) entered forwarding state
[ 122.160025] ohci-pci 0000:00:12.0: frame counter not updating; disabled
[ 122.160064] ohci-pci 0000:00:12.0: HC died; cleaning up
[ 122.160151] usb 11-3: USB disconnect, device number 2
[ 122.163302] usb 11-4: USB disconnect, device number 3
[ 154.647920] lan0: port 5(vif6.0) entered blocking state
[ 154.647922] lan0: port 5(vif6.0) entered disabled state
[ 154.648010] device vif6.0 entered promiscuous mode
[ 154.650934] IPv6: ADDRCONF(NETDEV_UP): vif6.0: link is not ready
[ 156.287702] vif vif-6-0 vif6.0: Guest Rx ready
[ 156.287769] IPv6: ADDRCONF(NETDEV_CHANGE): vif6.0: link becomes ready
[ 156.287828] lan0: port 5(vif6.0) entered blocking state
[ 156.287829] lan0: port 5(vif6.0) entered forwarding state
[ 156.292096] xen-blkback: backend/vbd/6/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 246.999319] device vif2.0 left promiscuous mode
[ 5262.955605] usb 10-2: new full-speed USB device number 2 using xhci_hcd
[ 5263.144855] usb 10-2: New USB device found, idVendor=04d8, idProduct=c002
[ 5263.144858] usb 10-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5263.144860] usb 10-2: Product: USB-LCD-256x64
[ 5263.144861] usb 10-2: Manufacturer: ITUNER INC
[ 5263.144862] usb 10-2: SerialNumber: Ver.00.03
[ 5263.295744] input: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/input/input17
[ 5263.295822] Registered IR keymap rc-rc6-mce
[ 5263.295892] input: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/rc/rc0/input18
[ 5263.295928] rc rc0: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/rc/rc0
[ 5263.296313] rc rc0: lirc_dev: driver ir-lirc-codec (PicoLCD (graphic)) registered at minor = 0
[ 5263.297259] Console: switching to mono frame buffer device 32x8
[ 5280.099829] Console: switching to colour VGA+ 80x25
[ 5727.382715] device vif8.0 entered promiscuous mode
[ 5727.385595] IPv6: ADDRCONF(NETDEV_UP): vif8.0: link is not ready
[ 5728.957119] xen-blkback: backend/vbd/8/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 5728.993444] vif vif-8-0 vif8.0: Guest Rx ready
[ 5728.993511] IPv6: ADDRCONF(NETDEV_CHANGE): vif8.0: link becomes ready
[ 5838.321825] audit: type=1305 audit(1494695633.399:2): audit_pid=6641 old=0 auid=4294967295 ses=4294967295 res=1
** Model information
sys_vendor: To Be Filled By O.E.M.
product_name: To Be Filled By O.E.M.
product_version: To Be Filled By O.E.M.
chassis_vendor: To Be Filled By O.E.M.
chassis_version: To Be Filled By O.E.M.
bios_vendor: American Megatrends Inc.
bios_version: P3.30
board_vendor: ASRock
board_name: FM2A88X Extreme4+
board_version:
** Loaded modules:
xt_physdev
br_netfilter
iptable_filter
xen_netback
xen_blkback
xen_gntdev
xen_evtchn
xenfs
xen_privcmd
8021q
garp
mrp
bridge
stp
llc
edac_mce_amd
edac_core
crct10dif_pclmul
crc32_pclmul
ghash_clmulni_intel
snd_hda_codec_realtek
ir_lirc_codec
snd_hda_codec_generic
lirc_dev
snd_hda_codec_hdmi
ir_rc6_decoder
snd_hda_intel
rc_rc6_mce
amdkfd
evdev
pcspkr
snd_hda_codec
radeon
serio_raw
snd_hda_core
ttm
shpchp
snd_hwdep
snd_pcm
drm_kms_helper
snd_timer
snd
soundcore
sg
hid_picolcd
rc_core
fam15h_power
k10temp
drm
sp5100_tco
i2c_algo_bit
video
button
tpm_tis
tpm_tis_core
tpm
nfsd
aoe
ip_tables
x_tables
autofs4
xfs
raid10
raid0
multipath
linear
rpcsec_gss_krb5
auth_rpcgss
nfsv4
dns_resolver
nfsv3
nfs_acl
nfs
lockd
grace
sunrpc
fscache
dm_snapshot
dm_bufio
dm_mod
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
libcrc32c
crc32c_generic
raid1
md_mod
hid_generic
usbhid
hid
sr_mod
cdrom
sd_mod
ata_generic
ohci_pci
crc32c_intel
aesni_intel
aes_x86_64
glue_helper
lrw
alx
gf128mul
ablk_helper
mdio
cryptd
ahci
libahci
xhci_pci
pata_atiixp
uhci_hcd
xhci_hcd
ohci_hcd
ehci_pci
libata
ehci_hcd
i2c_piix4
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Root Complex [1022:1422]
Subsystem: ASRock Incorporation Family 15h (Models 30h-3fh) Processor Root Complex [1849:1422]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 IOMMU [0806]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) I/O Memory Management Unit [1022:1423]
Subsystem: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) I/O Memory Management Unit [1022:1423]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
Capabilities: <access denied>
00:01.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Kaveri [Radeon R7 Graphics] [1002:1313] (prog-if 00 [VGA controller])
Subsystem: ASRock Incorporation Kaveri [Radeon R7 Graphics] [1849:1313]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=8M]
Region 4: I/O ports at f000 [size=256]
Region 5: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeon
00:01.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Kaveri HDMI/DP Audio Controller [1002:1308]
Subsystem: ASRock Incorporation Kaveri HDMI/DP Audio Controller [1849:1308]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 107
Region 0: Memory at feb64000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:02.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:03.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:04.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller [1022:7814] (rev 09) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation FCH USB XHCI Controller [1849:7814]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb6a000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:10.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller [1022:7814] (rev 09) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation FCH USB XHCI Controller [1849:7814]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb68000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] [1022:7801] (rev 40) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation FCH SATA Controller [AHCI mode] [1849:7801]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 32
Interrupt: pin A routed to IRQ 91
Region 0: I/O ports at f190 [size=8]
Region 1: I/O ports at f180 [size=4]
Region 2: I/O ports at f170 [size=8]
Region 3: I/O ports at f160 [size=4]
Region 4: I/O ports at f150 [size=16]
Region 5: Memory at feb71000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7807] (rev 11) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7807]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb70000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller [1022:7808] (rev 11) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation FCH USB EHCI Controller [1849:7808]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb6f000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7807] (rev 11) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7807]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb6e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller [1022:7808] (rev 11) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation FCH USB EHCI Controller [1849:7808]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb6d000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller [1022:780b] (rev 16)
Subsystem: ASRock Incorporation FCH SMBus Controller [1849:780b]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4, sp5100_tco
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller [1022:780c] (prog-if 8a [Master SecP PriP])
Subsystem: ASRock Incorporation FCH IDE Controller [1849:780c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at f100 [size=16]
Kernel driver in use: pata_atiixp
Kernel modules: pata_atiixp, ata_generic
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller [1022:780d] (rev 01)
Subsystem: ASRock Incorporation FCH Azalia Controller [1849:c892]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feb60000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge [1022:780e] (rev 11)
Subsystem: ASRock Incorporation FCH LPC Bridge [1849:780e]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge [1022:780f] (rev 40) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7809] (rev 11) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at feb6c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:15.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 0) [1022:43a0] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 86
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:15.2 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 2) [1022:43a2] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 87
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:15.3 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 3) [1022:43a3] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 88
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe800000-fe8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 0 [1022:141a]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 1 [1022:141b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 2 [1022:141c]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 3 [1022:141d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 4 [1022:141e]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: fam15h_power
Kernel modules: fam15h_power
00:18.5 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 5 [1022:141f]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:05.0 USB controller [0c03]: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e020 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
01:05.1 USB controller [0c03]: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
01:05.2 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 Controller [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fea00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
03:00.0 USB controller [0c03]: Etron Technology, Inc. EJ188/EJ198 USB 3.0 Host Controller [1b6f:7052] (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation EJ188/EJ198 USB 3.0 Host Controller [1849:7052]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 105
Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
04:00.0 Ethernet controller [0200]: Qualcomm Atheros QCA8171 Gigabit Ethernet [1969:10a1] (rev 10)
Subsystem: ASRock Incorporation QCA8171 Gigabit Ethernet [1849:10a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 106
Region 0: Memory at fe800000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at d000 [size=128]
Capabilities: <access denied>
Kernel driver in use: alx
Kernel modules: alx
** USB devices:
Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 010 Device 002: ID 04d8:c002 Microchip Technology, Inc.
Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 014 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 013 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 9.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64
(x86_64)
Kernel: Linux 4.9.0-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.9.0-2-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.9.0-2-amd64 recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-4.9.0-2-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta3-5
pn linux-doc-4.9 <none>
Versions of packages linux-image-4.9.0-2-amd64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
ii xen-hypervisor-4.8-amd64 [xen-hypervisor] 4.8.1-1+deb9u1
-- no debconf information
--- End Message ---