[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#988539: linux-image-5.10.0-6-amd64: umount of a USB stick froze the system



Package: src:linux
Version: 5.10.28-1
Severity: important

I copied a big file (> 3 GB) on a USB stick and did "umount" on the
device, and after a few dozens of seconds, the system got completely
frozen (the clock stopped, I couldn't move the mouse pointer, and
the keyboard wasn't reacting either) and the fan was making a lot of
noise. I had to switch off the machine.

After rebooting, I could see in the logs:

May 15 10:41:45 zira kernel: scsi 6:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
May 15 10:41:45 zira kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
May 15 10:41:45 zira kernel: sd 6:0:0:0: [sdb] 30720000 512-byte logical blocks: (15.7 GB/14.6 GiB)
May 15 10:41:45 zira kernel: sd 6:0:0:0: [sdb] Write Protect is off
May 15 10:41:45 zira kernel: sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
May 15 10:41:45 zira kernel: sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
May 15 10:41:45 zira kernel:  sdb: sdb1
May 15 10:41:45 zira kernel: sd 6:0:0:0: [sdb] Attached SCSI removable disk
May 15 10:42:12 zira kernel: FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

This was *before* I had mounted the volume and done the copy.

I don't know wheter whether the corrupt FS was related to the freeze,
but this shouldn't be a reason to freeze the system.

-- Package-specific info:
** Version:
Linux version 5.10.0-6-amd64 (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.28-1 (2021-04-09)

** Command line:
BOOT_IMAGE=/vmlinuz-5.10.0-6-amd64 root=/dev/mapper/zira--vg-root ro quiet systemd.swap=no

** Tainted: POE (12289)
 * proprietary module was loaded
 * externally-built ("out-of-tree") module was loaded
 * unsigned module was loaded

** Kernel log:
Unable to read kernel log; any relevant messages should be attached

** Model information
sys_vendor: Hewlett-Packard
product_name: HP ZBook 15 G2
product_version: A3008CD10003
chassis_vendor: Hewlett-Packard
chassis_version: 
bios_vendor: Hewlett-Packard
bios_version: M70 Ver. 01.08
board_vendor: Hewlett-Packard
board_name: 2253
board_version: KBC Version 03.10

** Loaded modules:
nls_ascii
nls_cp437
vfat
fat
uas
usb_storage
ctr
ccm
rfcomm
cmac
algif_hash
algif_skcipher
af_alg
bnep
cpufreq_conservative
cpufreq_ondemand
cpufreq_userspace
cpufreq_powersave
intel_rapl_msr
intel_rapl_common
x86_pkg_temp_thermal
intel_powerclamp
snd_hda_codec_realtek
btusb
binfmt_misc
coretemp
btrtl
iwlmvm
btbcm
snd_hda_codec_generic
btintel
mei_wdt
snd_hda_codec_hdmi
rapl
ledtrig_audio
mac80211
bluetooth
snd_hda_intel
snd_intel_dspcfg
soundwire_intel
soundwire_generic_allocation
snd_soc_core
libarc4
snd_compress
soundwire_cadence
intel_cstate
snd_hda_codec
jitterentropy_rng
iwlwifi
uvcvideo
videobuf2_vmalloc
snd_hda_core
videobuf2_memops
videobuf2_v4l2
snd_hwdep
soundwire_bus
videobuf2_common
drbg
snd_pcm
cfg80211
videodev
ansi_cprng
intel_uncore
joydev
mc
snd_timer
iTCO_wdt
hp_wmi
intel_pmc_bxt
mei_me
tpm_infineon
serio_raw
wmi_bmof
sparse_keymap
ecdh_generic
iTCO_vendor_support
snd
at24
ecc
pcspkr
sg
watchdog
rfkill
mxm_wmi
mei
soundcore
evdev
tpm_tis
tpm_tis_core
tpm
hp_accel
lis3lv02d
rng_core
hp_wireless
ac
button
nvidia_drm(POE)
drm_kms_helper
cec
nvidia_modeset(POE)
nvidia(POE)
ipmi_devintf
ipmi_msghandler
parport_pc
ppdev
lp
drm
parport
fuse
configfs
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
dm_crypt
dm_mod
sd_mod
sr_mod
t10_pi
cdrom
crc_t10dif
crct10dif_generic
crct10dif_pclmul
crct10dif_common
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
rtsx_pci_sdmmc
mmc_core
ahci
libahci
aesni_intel
xhci_pci
libaes
crypto_simd
libata
xhci_hcd
ehci_pci
cryptd
glue_helper
ehci_hcd
e1000e
psmouse
scsi_mod
usbcore
rtsx_pci
i2c_i801
lpc_ich
i2c_smbus
ptp
pps_core
usb_common
battery
video
wmi

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller [8086:0c04] (rev 06)
	Subsystem: Hewlett-Packard Company Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: ie31200_edac

00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [8086:0c01] (rev 06) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 24
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00005000-00005fff [size=4K]
	Memory behind bridge: d1000000-d20fffff [size=17M]
	Prefetchable memory behind bridge: 0000000070000000-0000000081ffffff [size=288M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 04) (prog-if 30 [XHCI])
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family USB xHCI [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 32
	Region 0: Memory at d2120000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family MEI Controller [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 34
	Region 0: Memory at d2138000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>
	Kernel driver in use: mei_me
	Kernel modules: mei_me

00:16.3 Serial controller [0700]: Intel Corporation 8 Series/C220 Series Chipset Family KT Controller [8086:8c3d] (rev 04) (prog-if 02 [16550])
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family KT Controller [103c:2253]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 0: I/O ports at 6070 [size=8]
	Region 1: Memory at d213b000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: serial

00:19.0 Ethernet controller [0200]: Intel Corporation Ethernet Connection I217-LM [8086:153a] (rev 04)
	Subsystem: Hewlett-Packard Company Ethernet Connection I217-LM [103c:2253]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 31
	Region 0: Memory at d2100000 (32-bit, non-prefetchable) [size=128K]
	Region 1: Memory at d213a000 (32-bit, non-prefetchable) [size=4K]
	Region 2: I/O ports at 6040 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: e1000e
	Kernel modules: e1000e

00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 [8086:8c2d] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family USB EHCI [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d2136000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 04)
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset High Definition Audio Controller [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 36
	Region 0: Memory at d2130000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 [8086:8c10] (rev d4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 25
	Bus: primary=00, secondary=02, subordinate=3a, sec-latency=0
	I/O behind bridge: 00002000-00002fff [size=4K]
	Memory behind bridge: b4000000-ca0fffff [size=353M]
	Prefetchable memory behind bridge: 0000000090000000-00000000b1ffffff [size=544M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.6 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #7 [8086:8c1c] (rev d4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 26
	Bus: primary=00, secondary=3b, subordinate=5f, sec-latency=0
	I/O behind bridge: 00003000-00004fff [size=8K]
	Memory behind bridge: cc000000-d01fffff [size=66M]
	Prefetchable memory behind bridge: 0000000060100000-00000000606fffff [size=6M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 [8086:8c26] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family USB EHCI [103c:2253]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at d2135000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1f.0 ISA bridge [0601]: Intel Corporation QM87 Express LPC Controller [8086:8c4f] (rev 04)
	Subsystem: Hewlett-Packard Company QM87 Express LPC Controller [103c:2253]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c03] (rev 04) (prog-if 01 [AHCI 1.0])
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [103c:2253]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 33
	Region 0: I/O ports at 6068 [size=8]
	Region 1: I/O ports at 607c [size=4]
	Region 2: I/O ports at 6060 [size=8]
	Region 3: I/O ports at 6078 [size=4]
	Region 4: I/O ports at 6020 [size=32]
	Region 5: Memory at d2134000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 04)
	Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family SMBus Controller [103c:2253]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at d2137000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at ef80 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c_i801

01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GK208GLM [Quadro K610M] [10de:12b9] (rev a1) (prog-if 00 [VGA controller])
	DeviceName: 0
	Subsystem: Hewlett-Packard Company GK208GLM [Quadro K610M] [103c:2254]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 37
	Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at 70000000 (64-bit, prefetchable) [size=256M]
	Region 3: Memory at 80000000 (64-bit, prefetchable) [size=32M]
	Region 5: I/O ports at 5000 [size=128]
	Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: nvidia
	Kernel modules: nvidia

01:00.1 Audio device [0403]: NVIDIA Corporation GK208 HDMI/DP Audio Controller [10de:0e0f] (rev a1)
	Subsystem: Hewlett-Packard Company GK208 HDMI/DP Audio Controller [103c:2254]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

3b:00.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G404 EL/SL PCIe2 4-Port/4-Lane Packet Switch [12d8:2404] (rev 05) (prog-if 00 [Normal decode])
	DeviceName: WLAN
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=3b, secondary=3c, subordinate=5f, sec-latency=0
	I/O behind bridge: 00003000-00004fff [size=8K]
	Memory behind bridge: cc000000-d01fffff [size=66M]
	Prefetchable memory behind bridge: 0000000060100000-00000000606fffff [size=6M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

3c:01.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G404 EL/SL PCIe2 4-Port/4-Lane Packet Switch [12d8:2404] (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 27
	Bus: primary=3c, secondary=3d, subordinate=3d, sec-latency=0
	I/O behind bridge: [disabled]
	Memory behind bridge: d0100000-d01fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

3c:02.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G404 EL/SL PCIe2 4-Port/4-Lane Packet Switch [12d8:2404] (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 28
	Bus: primary=3c, secondary=3e, subordinate=5e, sec-latency=0
	I/O behind bridge: 00003000-00004fff [size=8K]
	Memory behind bridge: cc000000-cfffffff [size=64M]
	Prefetchable memory behind bridge: 0000000060100000-00000000602fffff [size=2M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

3c:03.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G404 EL/SL PCIe2 4-Port/4-Lane Packet Switch [12d8:2404] (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 29
	Bus: primary=3c, secondary=5f, subordinate=5f, sec-latency=0
	I/O behind bridge: [disabled]
	Memory behind bridge: d0000000-d00fffff [size=1M]
	Prefetchable memory behind bridge: 0000000060300000-00000000604fffff [size=2M]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

3d:00.0 Network controller [0280]: Intel Corporation Wireless 7260 [8086:08b1] (rev 6b)
	Subsystem: Intel Corporation Dual Band Wireless-AC 7260 [8086:c070]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 35
	Region 0: Memory at d0100000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi

5f:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5249 PCI Express Card Reader [10ec:5249] (rev 01)
	Subsystem: Hewlett-Packard Company RTS5249 PCI Express Card Reader [103c:2253]
	Physical Slot: 0-2
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 30
	Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: rtsx_pci
	Kernel modules: rtsx_pci


** USB devices:
Bus 004 Device 002: ID 8087:8000 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 006: ID 058f:6387 Alcor Micro Corp. Flash Drive
Bus 002 Device 004: ID 05c8:0374 Cheng Uei Precision Industry Co., Ltd (Foxlink) HP EliteBook integrated HD Webcam
Bus 002 Device 003: ID 138a:003f Validity Sensors, Inc. VFS495 Fingerprint Reader
Bus 002 Device 002: ID 0e8d:2008 MediaTek Inc. Cyrus Technology CS 24
Bus 002 Device 005: ID 8087:07dc Intel Corp. Bluetooth wireless interface
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 11.0
  APT prefers unstable-debug
  APT policy: (500, 'unstable-debug'), (500, 'testing-security'), (500, 'stable-updates'), (500, 'unstable'), (500, 'testing'), (500, 'stable'), (1, 'experimental')
Architecture: amd64 (x86_64)

Kernel: Linux 5.10.0-6-amd64 (SMP w/8 CPU threads)
Kernel taint flags: TAINT_PROPRIETARY_MODULE, TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
Locale: LANG=POSIX, LC_CTYPE=C.UTF-8 (charmap=UTF-8), LANGUAGE not set
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled

Versions of packages linux-image-5.10.0-6-amd64 depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.140
ii  kmod                                    28-1
ii  linux-base                              4.6

Versions of packages linux-image-5.10.0-6-amd64 recommends:
ii  apparmor             2.13.6-10
ii  firmware-linux-free  20200122-1

Versions of packages linux-image-5.10.0-6-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 2.04-17
ii  linux-doc-5.10          5.10.28-1

Versions of packages linux-image-5.10.0-6-amd64 is related to:
pn  firmware-amd-graphics     <none>
pn  firmware-atheros          <none>
pn  firmware-bnx2             <none>
pn  firmware-bnx2x            <none>
pn  firmware-brcm80211        <none>
pn  firmware-cavium           <none>
pn  firmware-intel-sound      <none>
pn  firmware-intelwimax       <none>
pn  firmware-ipw2x00          <none>
pn  firmware-ivtv             <none>
ii  firmware-iwlwifi          20210315-2
pn  firmware-libertas         <none>
pn  firmware-linux-nonfree    <none>
pn  firmware-misc-nonfree     <none>
pn  firmware-myricom          <none>
pn  firmware-netxen           <none>
pn  firmware-qlogic           <none>
pn  firmware-realtek          <none>
pn  firmware-samsung          <none>
pn  firmware-siano            <none>
pn  firmware-ti-connectivity  <none>
pn  xen-hypervisor            <none>

-- no debconf information

-- 
Vincent Lefèvre <vincent@vinc17.net> - Web: <https://www.vinc17.net/>
100% accessible validated (X)HTML - Blog: <https://www.vinc17.net/blog/>
Work: CR INRIA - computer arithmetic / AriC project (LIP, ENS-Lyon)


Reply to: