--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-4.4.0-0.bpo.1-686-pae: Intel i915 : xrandr -s does hang the kernel
- From: rpnpif <rpnpif@free.fr>
- Date: Mon, 18 Apr 2016 09:05:39 +0200
- Message-id: <20160418070539.1952.98709.reportbug@Asus-901>
Package: src:linux
Version: 4.4.6-1~bpo8+1
Severity: normal
Dear Maintainer,
Each time that I run "xrandr -s 800x600" or "xrandr -s 1024x600", syslog logs
debug messages saying about issues of the kernel (see below).
No other effects out of this log.
xrandr seems to work fine.
$ xrandr
Screen 0: minimum 8 x 8, current 1024 x 600, maximum 32767 x 32767
LVDS1 connected 1024x600+0+0 (normal left inverted right x axis y axis) 195mm x 113mm
1024x600 60.00*+
800x600 60.32 56.25
640x480 59.94
VGA1 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
-- Package-specific info:
** Version:
Linux version 4.4.0-0.bpo.1-686-pae (debian-kernel@lists.debian.org) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Debian 4.4.6-1~bpo8+1 (2016-03-20)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.4.0-0.bpo.1-686-pae root=UUID=2ed3bc82-5cc0-4529-a13c-2e6f80b5b588 ro quiet
** Tainted: W (512)
* Taint on warning.
** Kernel log:
[ 2022.347925] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2022.347971] [<f864e7c5>] ? drm_atomic_check_only+0x2b5/0x650 [drm]
[ 2022.348012] [<f864d3a3>] ? drm_modeset_lock+0x33/0xf0 [drm]
[ 2022.348052] [<f864dedd>] ? drm_atomic_set_crtc_for_connector+0x1d/0xa0 [drm]
[ 2022.348094] [<f864eb92>] ? drm_atomic_commit+0x32/0x60 [drm]
[ 2022.348118] [<f86a3d42>] ? drm_atomic_helper_set_config+0x62/0xa0 [drm_kms_helper]
[ 2022.348161] [<f863eb4e>] ? drm_mode_set_config_internal+0x4e/0xc0 [drm]
[ 2022.348203] [<f8642c04>] ? drm_mode_setcrtc+0x1a4/0x570 [drm]
[ 2022.348247] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2022.348285] [<f863438c>] ? drm_ioctl+0x14c/0x510 [drm]
[ 2022.348302] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2022.348316] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2022.348358] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2022.348401] [<f8634240>] ? drm_getmap+0xc0/0xc0 [drm]
[ 2022.348415] [<c11c7a22>] ? do_vfs_ioctl+0x322/0x550
[ 2022.348427] [<c11cb6d7>] ? dput+0xb7/0x210
[ 2022.348441] [<c11f4186>] ? __fsnotify_parent+0x96/0x100
[ 2022.348456] [<c11b5680>] ? vfs_write+0x150/0x1b0
[ 2022.348470] [<c11c7cb0>] ? SyS_ioctl+0x60/0x90
[ 2022.348485] [<c10038f3>] ? do_fast_syscall_32+0x93/0x220
[ 2022.348501] [<c153ee98>] ? sysenter_past_esp+0x3d/0x61
[ 2022.348545] ---[ end trace 10505acfd6e5984f ]---
[ 2029.524389] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in gmch_pfit.lvds_border_bits (expected 0x00008000, found 0x00000000)
[ 2029.524408] ------------[ cut here ]------------
[ 2029.524519] WARNING: CPU: 0 PID: 641 at /home/zumbi/linux-4.4.6/drivers/gpu/drm/i915/intel_display.c:12812 intel_atomic_commit+0xae1/0x12d0 [i915]()
[ 2029.524527] pipe state doesn't match!
[ 2029.524534] Modules linked in: sha256_generic hmac drbg ansi_cprng ctr ccm binfmt_misc iTCO_wdt iTCO_vendor_support arc4 uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media rt2800pci rt2800mmio rt2800lib rt2x00pci rt2x00mmio rt2x00lib eeprom_93cx6 mac80211 coretemp evdev joydev i915 pcspkr cfg80211 serio_raw lpc_ich mfd_core eeepc_laptop crc_ccitt sparse_keymap i2c_i801 rfkill snd_hda_codec_realtek snd_hda_codec_generic rng_core snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep drm_kms_helper snd_pcm acpi_cpufreq tpm_tis snd_timer snd soundcore drm video i2c_algo_bit tpm battery ac shpchp button processor loop fuse parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd2 sg sd_mod ata_generic psmouse ata_piix libata scsi_mod ehci_pci uhci_hcd ehci_hcd
[ 2029.524782] usbcore usb_common thermal atl1e
[ 2029.524808] CPU: 0 PID: 641 Comm: Xorg Tainted: G W 4.4.0-0.bpo.1-686-pae #1 Debian 4.4.6-1~bpo8+1
[ 2029.524816] Hardware name: ASUSTeK Computer INC. 901/901, BIOS 2103 06/11/2009
[ 2029.524826] 00203286 af31f475 f4a01c98 c12ba29c f4a01ca8 00000000 c106b5c1 f8a5dbca
[ 2029.524851] f4a01cc8 00000281 f8a4f190 0000320c f89ef9f1 00000009 0000320c f89ef9f1
[ 2029.524875] f4a1a800 f51e5c00 f3d00000 f4a01cb4 c106b62e 00000009 f4a01ca8 f8a5dbca
[ 2029.524898] Call Trace:
[ 2029.524921] [<c12ba29c>] ? dump_stack+0x55/0x79
[ 2029.524938] [<c106b5c1>] ? warn_slowpath_common+0x91/0xc0
[ 2029.525047] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2029.525153] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2029.525167] [<c106b62e>] ? warn_slowpath_fmt+0x3e/0x60
[ 2029.525274] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2029.525320] [<f864e7c5>] ? drm_atomic_check_only+0x2b5/0x650 [drm]
[ 2029.525361] [<f864d3a3>] ? drm_modeset_lock+0x33/0xf0 [drm]
[ 2029.525402] [<f864dedd>] ? drm_atomic_set_crtc_for_connector+0x1d/0xa0 [drm]
[ 2029.525443] [<f864eb92>] ? drm_atomic_commit+0x32/0x60 [drm]
[ 2029.525468] [<f86a3d42>] ? drm_atomic_helper_set_config+0x62/0xa0 [drm_kms_helper]
[ 2029.525511] [<f863eb4e>] ? drm_mode_set_config_internal+0x4e/0xc0 [drm]
[ 2029.525553] [<f8642c04>] ? drm_mode_setcrtc+0x1a4/0x570 [drm]
[ 2029.525598] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2029.525636] [<f863438c>] ? drm_ioctl+0x14c/0x510 [drm]
[ 2029.525652] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2029.525666] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2029.525709] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2029.525752] [<f8634240>] ? drm_getmap+0xc0/0xc0 [drm]
[ 2029.525766] [<c11c7a22>] ? do_vfs_ioctl+0x322/0x550
[ 2029.525778] [<c11cb6d7>] ? dput+0xb7/0x210
[ 2029.525792] [<c11f4186>] ? __fsnotify_parent+0x96/0x100
[ 2029.525807] [<c11b5680>] ? vfs_write+0x150/0x1b0
[ 2029.525820] [<c11c7cb0>] ? SyS_ioctl+0x60/0x90
[ 2029.525835] [<c10038f3>] ? do_fast_syscall_32+0x93/0x220
[ 2029.525852] [<c153ee98>] ? sysenter_past_esp+0x3d/0x61
[ 2029.525862] ---[ end trace 10505acfd6e59850 ]---
[ 2070.912384] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in gmch_pfit.lvds_border_bits (expected 0x00008000, found 0x00000000)
[ 2070.912400] ------------[ cut here ]------------
[ 2070.912483] WARNING: CPU: 0 PID: 641 at /home/zumbi/linux-4.4.6/drivers/gpu/drm/i915/intel_display.c:12812 intel_atomic_commit+0xae1/0x12d0 [i915]()
[ 2070.912489] pipe state doesn't match!
[ 2070.912495] Modules linked in: sha256_generic hmac drbg ansi_cprng ctr ccm binfmt_misc iTCO_wdt iTCO_vendor_support arc4 uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media rt2800pci rt2800mmio rt2800lib rt2x00pci rt2x00mmio rt2x00lib eeprom_93cx6 mac80211 coretemp evdev joydev i915 pcspkr cfg80211 serio_raw lpc_ich mfd_core eeepc_laptop crc_ccitt sparse_keymap i2c_i801 rfkill snd_hda_codec_realtek snd_hda_codec_generic rng_core snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep drm_kms_helper snd_pcm acpi_cpufreq tpm_tis snd_timer snd soundcore drm video i2c_algo_bit tpm battery ac shpchp button processor loop fuse parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd2 sg sd_mod ata_generic psmouse ata_piix libata scsi_mod ehci_pci uhci_hcd ehci_hcd
[ 2070.912682] usbcore usb_common thermal atl1e
[ 2070.912702] CPU: 0 PID: 641 Comm: Xorg Tainted: G W 4.4.0-0.bpo.1-686-pae #1 Debian 4.4.6-1~bpo8+1
[ 2070.912708] Hardware name: ASUSTeK Computer INC. 901/901, BIOS 2103 06/11/2009
[ 2070.912715] 00203286 af31f475 f4a01c98 c12ba29c f4a01ca8 00000000 c106b5c1 f8a5dbca
[ 2070.912735] f4a01cc8 00000281 f8a4f190 0000320c f89ef9f1 00000009 0000320c f89ef9f1
[ 2070.912753] f4a1a800 f5fbd800 f3d01000 f4a01cb4 c106b62e 00000009 f4a01ca8 f8a5dbca
[ 2070.912771] Call Trace:
[ 2070.912788] [<c12ba29c>] ? dump_stack+0x55/0x79
[ 2070.912801] [<c106b5c1>] ? warn_slowpath_common+0x91/0xc0
[ 2070.912883] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2070.912963] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2070.912974] [<c106b62e>] ? warn_slowpath_fmt+0x3e/0x60
[ 2070.913054] [<f89ef9f1>] ? intel_atomic_commit+0xae1/0x12d0 [i915]
[ 2070.913089] [<f864e7c5>] ? drm_atomic_check_only+0x2b5/0x650 [drm]
[ 2070.913119] [<f864d3a3>] ? drm_modeset_lock+0x33/0xf0 [drm]
[ 2070.913150] [<f864dedd>] ? drm_atomic_set_crtc_for_connector+0x1d/0xa0 [drm]
[ 2070.913181] [<f864eb92>] ? drm_atomic_commit+0x32/0x60 [drm]
[ 2070.913199] [<f86a3d42>] ? drm_atomic_helper_set_config+0x62/0xa0 [drm_kms_helper]
[ 2070.913232] [<f863eb4e>] ? drm_mode_set_config_internal+0x4e/0xc0 [drm]
[ 2070.913264] [<f8642c04>] ? drm_mode_setcrtc+0x1a4/0x570 [drm]
[ 2070.913297] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2070.913326] [<f863438c>] ? drm_ioctl+0x14c/0x510 [drm]
[ 2070.913338] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2070.913348] [<c11f42c7>] ? fsnotify_destroy_event+0x27/0x50
[ 2070.913380] [<f8642a60>] ? drm_mode_setplane+0x1d0/0x1d0 [drm]
[ 2070.913412] [<f8634240>] ? drm_getmap+0xc0/0xc0 [drm]
[ 2070.913423] [<c11c7a22>] ? do_vfs_ioctl+0x322/0x550
[ 2070.913432] [<c11cb6d7>] ? dput+0xb7/0x210
[ 2070.913443] [<c11f4186>] ? __fsnotify_parent+0x96/0x100
[ 2070.913454] [<c11b5680>] ? vfs_write+0x150/0x1b0
[ 2070.913464] [<c11c7cb0>] ? SyS_ioctl+0x60/0x90
[ 2070.913476] [<c10038f3>] ? do_fast_syscall_32+0x93/0x220
[ 2070.913488] [<c153ee98>] ? sysenter_past_esp+0x3d/0x61
[ 2070.913497] ---[ end trace 10505acfd6e59851 ]---
** Model information
** Loaded modules:
sha256_generic
hmac
drbg
ansi_cprng
ctr
ccm
binfmt_misc
iTCO_wdt
iTCO_vendor_support
arc4
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_v4l2
videobuf2_core
v4l2_common
videodev
media
rt2800pci
rt2800mmio
rt2800lib
rt2x00pci
rt2x00mmio
rt2x00lib
eeprom_93cx6
mac80211
coretemp
evdev
joydev
i915
pcspkr
cfg80211
serio_raw
lpc_ich
mfd_core
eeepc_laptop
crc_ccitt
sparse_keymap
i2c_i801
rfkill
snd_hda_codec_realtek
snd_hda_codec_generic
rng_core
snd_hda_intel
snd_hda_codec
snd_hda_core
snd_hwdep
drm_kms_helper
snd_pcm
acpi_cpufreq
tpm_tis
snd_timer
snd
soundcore
drm
video
i2c_algo_bit
tpm
battery
ac
shpchp
button
processor
loop
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
sg
sd_mod
ata_generic
psmouse
ata_piix
libata
scsi_mod
ehci_pci
uhci_hcd
ehci_hcd
usbcore
usb_common
thermal
atl1e
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GSE Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc80 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f7f80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:831a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-401fffff
Prefetchable memory behind bridge: 0000000040200000-00000000403fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbf00000-fbffffff
Prefetchable memory behind bridge: 0000000040400000-00000000405fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 40600000-407fffff
Prefetchable memory behind bridge: 0000000040800000-00000000409fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-fbefffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] [8086:27c4] (rev 02) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0400 [size=32]
01:00.0 Network controller [0280]: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe [1814:0781]
Subsystem: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe [1814:2790]
Physical Slot: eeepc-wifi
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: rt2800pci
04:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet [1969:1026] (rev b0)
Subsystem: ASUSTeK Computer Inc. Device [1043:8324]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ec80 [size=128]
Capabilities: <access denied>
Kernel driver in use: ATL1E
** USB devices:
Bus 005 Device 003: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.4
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 4.4.0-0.bpo.1-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.utf8, LC_CTYPE=fr_FR.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.4.0-0.bpo.1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120+deb8u1
ii kmod 18-3
ii linux-base 4.0~bpo8+1
Versions of packages linux-image-4.4.0-0.bpo.1-686-pae recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.0.6-3
ii libc6-i686 2.19-18+deb8u4
Versions of packages linux-image-4.4.0-0.bpo.1-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22+deb8u1
pn linux-doc-4.4 <none>
Versions of packages linux-image-4.4.0-0.bpo.1-686-pae is related to:
ii firmware-atheros 20160110-1~bpo8+1
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 20160110-1~bpo8+1
ii firmware-linux-nonfree 20160110-1~bpo8+1
ii firmware-misc-nonfree [firmware-ralink] 20160110-1~bpo8+1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-4.4.0-0.bpo.1-686-pae/prerm/removing-running-kernel-4.4.0-0.bpo.1-686-pae: true
--- End Message ---