--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.16.0-4-686-pae: huawei E5331 Buffer I/O error on device sr1
- From: Sergey <mont222@ya.ru>
- Date: Thu, 05 Mar 2015 20:26:54 +0900
- Message-id: <20150305112654.2588.7161.reportbug@debi32>
Package: src:linux
Version: 3.16.7-ckt4-3
Severity: normal
Dear Maintainer,
*** Reporter, please consider answering these questions, where appropriate ***
* What led up to the situation?
* What exactly did you do (or not do) that was effective (or
ineffective)?
* What was the outcome of this action?
* What outcome did you expect instead?
*** End of the template - remove these template lines ***
-- Package-specific info:
** Version:
Linux version 3.16.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt4-3 (2015-02-03)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-686-pae root=UUID=99da80b5-75d5-4f0d-a445-f9bc62a85399 ro quiet
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 2417.282651] usb 1-3: New USB device found, idVendor=12d1, idProduct=1c1e
[ 2417.282658] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[ 2417.282662] usb 1-3: Product: HUAWEI Mobile
[ 2417.282665] usb 1-3: Manufacturer: HUAWEI
[ 2417.286521] usb-storage 1-3:1.1: USB Mass Storage device detected
[ 2417.286821] scsi8 : usb-storage 1-3:1.1
[ 2417.287538] usb-storage 1-3:1.4: USB Mass Storage device detected
[ 2417.287857] scsi9 : usb-storage 1-3:1.4
[ 2417.638181] usbcore: registered new interface driver cdc_ether
[ 2417.658142] cdc_ncm 1-3:1.3: MAC-Address: 58:2c:80:13:92:63
[ 2417.658153] cdc_ncm 1-3:1.3: setting rx_max = 16384
[ 2417.658609] cdc_ncm 1-3:1.3: setting tx_max = 16384
[ 2417.659347] cdc_ncm 1-3:1.3 wwan0: register 'cdc_ncm' at usb-0000:00:14.0-3, Mobile Broadband Network Device, 58:2c:80:13:92:63
[ 2417.659613] usbcore: registered new interface driver cdc_ncm
[ 2417.659703] usbcore: registered new interface driver rndis_host
[ 2417.671838] usbcore: registered new interface driver rndis_wlan
[ 2417.687939] usbcore: registered new interface driver cdc_wdm
[ 2417.688609] usbcore: registered new interface driver cdc_mbim
[ 2418.285631] scsi 8:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 2418.285688] scsi 9:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 2418.286588] sr1: scsi-1 drive
[ 2418.286764] sr 8:0:0:0: Attached scsi CD-ROM sr1
[ 2418.286869] sr 8:0:0:0: Attached scsi generic sg3 type 5
[ 2418.287143] sd 9:0:0:0: Attached scsi generic sg4 type 0
[ 2418.289893] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[ 2449.123369] cdc_ncm 1-3:1.3 wwan0: unregister 'cdc_ncm' usb-0000:00:14.0-3, Mobile Broadband Network Device
[ 2449.327342] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2449.327374] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[ 2449.327378] usb 1-3: hub failed to enable device, error -22
[ 2449.439135] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2449.439160] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[ 2449.439166] usb 1-3: hub failed to enable device, error -22
[ 2449.551128] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2449.567670] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506570
[ 2449.567675] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506540
[ 2449.567678] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506640
[ 2449.567680] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506670
[ 2449.567683] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f26f4570
[ 2449.567685] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f26f4540
[ 2449.567688] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f68e7e40
[ 2449.567690] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ecba8cc0
[ 2449.567693] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ecba8cf0
[ 2449.591410] cdc_ncm 1-3:1.3: MAC-Address: 58:2c:80:13:92:63
[ 2449.591420] cdc_ncm 1-3:1.3: setting rx_max = 16384
[ 2449.591684] cdc_ncm 1-3:1.3: setting tx_max = 16384
[ 2449.592485] cdc_ncm 1-3:1.3 wwan0: register 'cdc_ncm' at usb-0000:00:14.0-3, Mobile Broadband Network Device, 58:2c:80:13:92:63
[ 2449.600299] sr 8:0:0:0: [sr1] Media Changed
[ 2449.600305] sr 8:0:0:0: [sr1]
[ 2449.600308] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2449.600310] sr 8:0:0:0: [sr1]
[ 2449.600313] Sense Key : Unit Attention [current]
[ 2449.600317] Info fld=0x0
[ 2449.600320] sr 8:0:0:0: [sr1]
[ 2449.600326] Add. Sense: Not ready to ready change, medium may have changed
[ 2449.600329] sr 8:0:0:0: [sr1] CDB:
[ 2449.600331] Read(10): 28 00 00 00 ff fe 00 00 02 00
[ 2449.600343] end_request: I/O error, dev sr1, sector 262136
[ 2449.600348] Buffer I/O error on device sr1, logical block 32767
[ 2480.089596] cdc_ncm 1-3:1.3 wwan0: unregister 'cdc_ncm' usb-0000:00:14.0-3, Mobile Broadband Network Device
[ 2480.281518] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2480.281547] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[ 2480.281551] usb 1-3: hub failed to enable device, error -22
[ 2480.393392] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2480.393419] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[ 2480.393436] usb 1-3: hub failed to enable device, error -22
[ 2480.505361] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2480.521823] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506570
[ 2480.521829] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506540
[ 2480.521832] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506640
[ 2480.521834] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep e9506670
[ 2480.521837] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f26f4570
[ 2480.521839] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f26f4540
[ 2480.521842] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f68e7e40
[ 2480.521845] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ecba8cc0
[ 2480.521847] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ecba8cf0
[ 2480.545905] cdc_ncm 1-3:1.3: MAC-Address: 58:2c:80:13:92:63
[ 2480.545911] cdc_ncm 1-3:1.3: setting rx_max = 16384
[ 2480.546091] cdc_ncm 1-3:1.3: setting tx_max = 16384
[ 2480.546509] cdc_ncm 1-3:1.3 wwan0: register 'cdc_ncm' at usb-0000:00:14.0-3, Mobile Broadband Network Device, 58:2c:80:13:92:63
[ 2480.553970] sr 8:0:0:0: [sr1] Media Changed
[ 2480.553981] sr 8:0:0:0: [sr1]
[ 2480.553986] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2480.553990] sr 8:0:0:0: [sr1]
[ 2480.553994] Sense Key : Unit Attention [current]
[ 2480.554001] Info fld=0x0
[ 2480.554005] sr 8:0:0:0: [sr1]
[ 2480.554013] Add. Sense: Not ready to ready change, medium may have changed
[ 2480.554018] sr 8:0:0:0: [sr1] CDB:
[ 2480.554021] Read(10): 28 00 00 00 ff fe 00 00 02 00
[ 2480.554037] end_request: I/O error, dev sr1, sector 262136
[ 2480.554045] Buffer I/O error on device sr1, logical block 32767
[ 2501.730807] cdc_ncm 1-3:1.3 wwan0: unregister 'cdc_ncm' usb-0000:00:14.0-3, Mobile Broadband Network Device
[ 2501.732868] usb 1-3: USB disconnect, device number 5
[ 2501.762573] sr 8:0:0:0: [sr1] Unhandled error code
[ 2501.762594] sr 8:0:0:0: [sr1]
[ 2501.762599] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 2501.762603] sr 8:0:0:0: [sr1] CDB:
[ 2501.762607] Read(10): 28 00 00 00 ff fe 00 00 02 00
[ 2501.762623] end_request: I/O error, dev sr1, sector 262136
[ 2501.762632] Buffer I/O error on device sr1, logical block 32767
** Model information
not available
** Loaded modules:
cdc_mbim
cdc_wdm
rndis_wlan
rndis_host
cdc_ncm
cdc_ether
usbnet
nls_utf8
nls_cp437
vfat
fat
usb_storage
bnep
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
wl(PO)
ecb
uvcvideo
videobuf2_vmalloc
videobuf2_memops
btusb
videobuf2_core
v4l2_common
bluetooth
videodev
media
6lowpan_iphc
cfg80211
x86_pkg_temp_thermal
snd_hda_codec_hdmi
intel_powerclamp
intel_rapl
coretemp
joydev
rtsx_pci_ms
i915
drm_kms_helper
memstick
iTCO_wdt
snd_hda_codec_realtek
iTCO_vendor_support
kvm
drm
snd_hda_codec_generic
mei_me
snd_hda_intel
crc32_pclmul
evdev
snd_hda_controller
pcspkr
psmouse
i2c_algo_bit
i2c_i801
snd_hda_codec
serio_raw
i2c_core
shpchp
mei
snd_hwdep
sony_laptop
lpc_ich
snd_pcm
snd_timer
rfkill
snd
soundcore
video
button
processor
ac
battery
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
sg
sd_mod
crc_t10dif
sr_mod
crct10dif_generic
cdrom
crct10dif_common
hid_generic
usbhid
hid
rtsx_pci_sdmmc
mmc_core
crc32c_intel
ahci
libahci
libata
rtsx_pci
mfd_core
ehci_pci
scsi_mod
xhci_hcd
ehci_hcd
r8169
mii
usbcore
thermal
usb_common
thermal_sys
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
link/ether 3c:07:71:58:d2:7f brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether b8:76:3f:c1:40:db brd ff:ff:ff:ff:ff:ff
inet 192.168.1.100/24 brd 192.168.1.255 scope global dynamic wlan0
valid_lft 83615sec preferred_lft 83615sec
inet6 fe80::ba76:3fff:fec1:40db/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
wlan0: 3443531 2616 0 0 0 6690 0 0 205680 1842 0 0 0 0 0 0
lo: 37884 465 0 0 0 0 0 0 37884 465 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
2992 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
2990 incoming packets delivered
2210 requests sent out
80 outgoing packets dropped
Icmp:
169 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 168
echo requests: 1
169 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 168
echo replies: 1
IcmpMsg:
InType3: 168
InType8: 1
OutType0: 1
OutType3: 168
Tcp:
35 active connections openings
8 passive connection openings
20 failed connection attempts
1 connection resets received
0 connections established
2490 segments received
1701 segments send out
5 segments retransmited
0 bad segments received.
21 resets sent
Udp:
204 packets received
168 packets to unknown port received.
0 packet receive errors
376 packets sent
UdpLite:
TcpExt:
11 TCP sockets finished time wait in fast timer
35 delayed acks sent
145 bytes directly in process context from backlog
2162 packet headers predicted
1 packets header predicted and directly queued to user
68 acknowledgments not containing data payload received
20 predicted acknowledgments
1 congestion windows recovered without slow start after partial ack
1 other TCP timeouts
TCPLossProbes: 4
TCPLossProbeRecovery: 2
3 DSACKs received
1 connections reset due to early user close
TCPDSACKIgnoredNoUndo: 1
TCPSackShiftFallback: 2
TCPRcvCoalesce: 92
TCPOFOQueue: 2
TCPAutoCorking: 4
TCPOrigDataSent: 150
IpExt:
InOctets: 3439029
OutOctets: 196248
InNoECTPkts: 2992
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: ivb_uncore
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 46
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 3000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4152
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Region 0: Memory at c0800000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4191
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at c0814000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4142
Kernel driver in use: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0819000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP+
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at c0810000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4122
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Memory behind bridge: c0700000-c07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Sony Corporation Device [104d:90b8]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Memory behind bridge: c0600000-c06fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Sony Corporation Device [104d:90b8]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0e, subordinate=0e, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0500000-c05fffff
Prefetchable memory behind bridge: 00000000c0400000-00000000c04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Sony Corporation Device [104d:90b8]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at c0818000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at 3088 [size=8]
Region 1: I/O ports at 3094 [size=4]
Region 2: I/O ports at 3080 [size=8]
Region 3: I/O ports at 3090 [size=4]
Region 4: I/O ports at 3060 [size=32]
Region 5: Memory at c0817000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41d1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at c0815000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 3040 [size=32]
07:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e071]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0700000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Vendor Specific Information: Len=78 <?>
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [13c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 00-00-3f-ff-ff-c1-b8-76
Capabilities: [16c v1] Power Budgeting <?>
Kernel driver in use: wl
08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader [10ec:5209] (rev 01)
Subsystem: Sony Corporation Device [104d:90b8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at c0600000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41a1
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 00-00-00-01-00-4c-e0-00
Kernel driver in use: rtsx_pci
0e:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 0c)
Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:0123]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at c0500000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at c0400000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41b1
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via message/WAKE#
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Unknown small resource type 00, will not decode more.
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: r8169
** USB devices:
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 004: ID 04f2:b3aa Chicony Electronics Co., Ltd
Bus 003 Device 003: ID 0489:e062 Foxconn / Hon Hai
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 0930:6544 Toshiba Corp. Kingston DataTraveler 2.0 Stick (2GB)
Bus 001 Device 002: ID 046d:c050 Logitech, Inc. RX 250 Optical Mouse
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 8.0
APT prefers testing-updates
APT policy: (500, 'testing-updates'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.16.0-4-686-pae (SMP w/4 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.55
ii initramfs-tools [linux-initramfs-tool] 0.116
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-4-686-pae recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
ii libc6-i686 2.19-15
Versions of packages linux-image-3.16.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-20
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.43
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-686-pae/postinst/depmod-error-initrd-3.16.0-4-686-pae: false
linux-image-3.16.0-4-686-pae/prerm/removing-running-kernel-3.16.0-4-686-pae: true
linux-image-3.16.0-4-686-pae/postinst/mips-initrd-3.16.0-4-686-pae:
*** /mnt/KMB/e5331_e3272/12d1-1c20debi32.log
@debi32:~ # cat /var/log/syslog
Mar 3 22:36:51 debi32 kernel: [ 9593.541107] usb 1-4: new high-speed USB device number 11 using xhci_hcd
Mar 3 22:36:51 debi32 kernel: [ 9593.669615] usb 1-4: New USB device found, idVendor=12d1, idProduct=1c20
Mar 3 22:36:51 debi32 kernel: [ 9593.669625] usb 1-4: New USB device strings: Mfr=2, Product=1, SerialNumber=0
Mar 3 22:36:51 debi32 kernel: [ 9593.669631] usb 1-4: Product: HUAWEI Mobile
Mar 3 22:36:51 debi32 kernel: [ 9593.669635] usb 1-4: Manufacturer: HUAWEI
Mar 3 22:36:51 debi32 kernel: [ 9593.671445] usb-storage 1-4:1.0: USB Mass Storage device detected
Mar 3 22:36:51 debi32 kernel: [ 9593.671658] scsi14 : usb-storage 1-4:1.0
Mar 3 22:36:51 debi32 mtp-probe: checking bus 1, device 11: "/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4"
Mar 3 22:36:51 debi32 mtp-probe: bus: 1, device: 11 was not an MTP device
Mar 3 22:36:52 debi32 kernel: [ 9594.669296] scsi 14:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Mar 3 22:36:52 debi32 kernel: [ 9594.670468] sr1: scsi-1 drive
Mar 3 22:36:52 debi32 kernel: [ 9594.670945] sr 14:0:0:0: Attached scsi CD-ROM sr1
Mar 3 22:36:52 debi32 kernel: [ 9594.671339] sr 14:0:0:0: Attached scsi generic sg3 type 5
Mar 3 22:37:22 debi32 systemd-udevd[194]: worker [7860] /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/host14/target14:0:0/14:0:0:0/block/sr1 timeout; kill it
Mar 3 22:37:22 debi32 systemd-udevd[194]: seq 2001 '/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/host14/target14:0:0/14:0:0:0/block/sr1' killed
Mar 3 22:37:23 debi32 kernel: [ 9625.894279] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
Mar 3 22:37:23 debi32 kernel: [ 9625.894308] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
Mar 3 22:37:23 debi32 kernel: [ 9625.894314] usb 1-4: hub failed to enable device, error -22
Mar 3 22:37:24 debi32 kernel: [ 9626.006053] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
Mar 3 22:37:24 debi32 kernel: [ 9626.006124] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
Mar 3 22:37:24 debi32 kernel: [ 9626.006134] usb 1-4: hub failed to enable device, error -22
Mar 3 22:37:24 debi32 kernel: [ 9626.118009] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
Mar 3 22:37:24 debi32 kernel: [ 9626.134281] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep eb86a140
Mar 3 22:37:24 debi32 kernel: [ 9626.134293] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep eb86a170
Mar 3 22:37:24 debi32 systemd-udevd[194]: worker [7860] terminated by signal 9 (Killed)
Mar 3 22:37:24 debi32 kernel: [ 9626.142512] sr 14:0:0:0: [sr1] Media Changed
Mar 3 22:37:24 debi32 kernel: [ 9626.142522] sr 14:0:0:0: [sr1]
Mar 3 22:37:24 debi32 kernel: [ 9626.142527] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Mar 3 22:37:24 debi32 kernel: [ 9626.142531] sr 14:0:0:0: [sr1]
Mar 3 22:37:24 debi32 kernel: [ 9626.142534] Sense Key : Unit Attention [current]
Mar 3 22:37:24 debi32 kernel: [ 9626.142540] Info fld=0x0
Mar 3 22:37:24 debi32 kernel: [ 9626.142543] sr 14:0:0:0: [sr1]
Mar 3 22:37:24 debi32 kernel: [ 9626.142550] Add. Sense: Not ready to ready change, medium may have changed
Mar 3 22:37:24 debi32 kernel: [ 9626.142554] sr 14:0:0:0: [sr1] CDB:
Mar 3 22:37:24 debi32 kernel: [ 9626.142557] Read(10): 28 00 00 00 ff fe 00 00 02 00
Mar 3 22:37:24 debi32 kernel: [ 9626.142572] end_request: I/O error, dev sr1, sector 262136
Mar 3 22:37:24 debi32 kernel: [ 9626.142579] Buffer I/O error on device sr1, logical block 32767
-------------------------------------------------
@debi32:~ # dmesg
[ 9593.541107] usb 1-4: new high-speed USB device number 11 using xhci_hcd
[ 9593.669615] usb 1-4: New USB device found, idVendor=12d1, idProduct=1c20
[ 9593.669625] usb 1-4: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[ 9593.669631] usb 1-4: Product: HUAWEI Mobile
[ 9593.669635] usb 1-4: Manufacturer: HUAWEI
[ 9593.671445] usb-storage 1-4:1.0: USB Mass Storage device detected
[ 9593.671658] scsi14 : usb-storage 1-4:1.0
[ 9594.669296] scsi 14:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 9594.670468] sr1: scsi-1 drive
[ 9594.670945] sr 14:0:0:0: Attached scsi CD-ROM sr1
[ 9594.671339] sr 14:0:0:0: Attached scsi generic sg3 type 5
[ 9625.894279] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
[ 9625.894308] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
[ 9625.894314] usb 1-4: hub failed to enable device, error -22
[ 9626.006053] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
[ 9626.006124] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
[ 9626.006134] usb 1-4: hub failed to enable device, error -22
[ 9626.118009] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
[ 9626.134281] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep eb86a140
[ 9626.134293] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep eb86a170
[ 9626.142512] sr 14:0:0:0: [sr1] Media Changed
[ 9626.142522] sr 14:0:0:0: [sr1]
[ 9626.142527] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 9626.142531] sr 14:0:0:0: [sr1]
[ 9626.142534] Sense Key : Unit Attention [current]
[ 9626.142540] Info fld=0x0
[ 9626.142543] sr 14:0:0:0: [sr1]
[ 9626.142550] Add. Sense: Not ready to ready change, medium may have changed
[ 9626.142554] sr 14:0:0:0: [sr1] CDB:
[ 9626.142557] Read(10): 28 00 00 00 ff fe 00 00 02 00
[ 9626.142572] end_request: I/O error, dev sr1, sector 262136
[ 9626.142579] Buffer I/O error on device sr1, logical block 32767
[ 9656.859719] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
[ 9656.859795] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
[ 9656.859805] usb 1-4: hub failed to enable device, error -22
[ 9656.971442] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
[ 9656.971523] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 10.
[ 9656.971534] usb 1-4: hub failed to enable device, error -22
[ 9657.083393] usb 1-4: reset high-speed USB device number 11 using xhci_hcd
---------------------------------------------------------------------------
@debi32:~ # usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 12 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1c20 Rev=01.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI Mobile
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
---------------------------------------------------------------------------------
@debi32:~ # lsusb -s 001:012 -v
Bus 001 Device 012: ID 12d1:1c20 Huawei Technologies Co., Ltd.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x12d1 Huawei Technologies Co., Ltd.
idProduct 0x1c20
bcdDevice 1.02
iManufacturer 2 HUAWEI
iProduct 1 HUAWEI Mobile
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
--- End Message ---