--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.12-1-amd64: network adapter 82579LM e1000e 0000:00:19.0 eth1: Detected Hardware Unit Hang
- From: Bozhan Boiadzhiev <bozhan@zlatograd.net>
- Date: Sat, 08 Feb 2014 10:52:59 +0200
- Message-id: <20140208085259.4546.95847.reportbug@zlatograd-1.zlatograd.net>
Package: src:linux
Version: 3.12.9-1
Severity: critical
Justification: causes serious data loss
Dear Maintainer,
Since upograde to some of 3.2.xxx kernels this massage start to appera in dmesg:
[ 37.927066] e1000e 0000:00:19.0 eth1: Detected Hardware Unit Hang:
[ 37.927066] TDH <0>
[ 37.927066] TDT <1>
[ 37.927066] next_to_use <1>
[ 37.927066] next_to_clean <0>
[ 37.927066] buffer_info[next_to_clean]:
[ 37.927066] time_stamp <fffefdfb>
[ 37.927066] next_to_watch <0>
[ 37.927066] jiffies <fffefff4>
[ 37.927066] next_to_watch.status <0>
[ 37.927066] MAC Status <40080080>
[ 37.927066] PHY Status <7949>
[ 37.927066] PHY 1000BASE-T Status <0>
[ 37.927066] PHY Extended Status <3000>
[ 37.927066] PCI Status <10>
this is message for adapter without even connected network cable.
If there is a high traffic load this hang occure more offten and
traffic stops until adapter is reset
e1000e 0000:00:19.0: eth0: Reset adapter
and then after minute hang again.
I have to used stop using this adapter and start useing other one integrated on board:
Intel Corporation 82574L
which doesn't have such problems.
-- Package-specific info:
** Version:
Linux version 3.12-1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-14) ) #1 SMP Debian 3.12.9-1 (2014-02-01)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.12-1-amd64 root=UUID=b6ec4e81-a321-4b4f-8b2a-552d460b397d ro quiet
** Not tainted
** Kernel log:
[ 4.401070] usbcore: registered new interface driver usbhid
[ 4.401072] usbhid: USB HID core driver
[ 4.435492] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20130725/utaddress-251)
[ 4.435497] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 4.435500] ACPI Warning: 0x0000000000000540-0x000000000000054f SystemIO conflicts with Region \GPIO 1 (20130725/utaddress-251)
[ 4.435502] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 4.435503] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20130725/utaddress-251)
[ 4.435505] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 4.435505] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20130725/utaddress-251)
[ 4.435507] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 4.435508] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 4.490907] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 4.490935] ACPI: Power Button [PWRB]
[ 4.490961] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.490980] ACPI: Power Button [PWRF]
[ 4.579771] ipmi message handler version 39.2
[ 4.582045] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[ 4.582120] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0
[ 4.582210] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
[ 4.582272] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1
[ 4.600120] IPMI System Interface driver.
[ 4.600138] ipmi_si: probing via ACPI
[ 4.600156] ipmi_si 00:0f: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 4.600157] ipmi_si: Adding ACPI-specified kcs state machine
[ 4.600166] ipmi_si: probing via SMBIOS
[ 4.600167] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0
[ 4.600168] ipmi_si: Adding SMBIOS-specified kcs state machine duplicate interface
[ 4.600170] ipmi_si: probing via SPMI
[ 4.600170] ipmi_si: SPMI: io 0xca2 regsize 1 spacing 1 irq 0
[ 4.600171] ipmi_si: Adding SPMI-specified kcs state machine duplicate interface
[ 4.600173] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 4.697997] ipmi_si: Invalid return from get global enables command, cannot enable the event buffer.
[ 4.701884] ipmi_si 00:0f: Found new BMC (man_id: 0x002a7c, prod_id: 0x0624, dev_id: 0x20)
[ 4.701891] ipmi_si 00:0f: IPMI kcs interface initialized
[ 4.704189] iTCO_vendor_support: vendor-support=0
[ 4.770939] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 4.770960] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 4.771057] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.832165] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.129269] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 5.209225] alg: No test for crc32 (crc32-pclmul)
[ 6.642715] EXT4-fs (md0): re-mounted. Opts: (null)
[ 6.831626] EXT4-fs (md0): re-mounted. Opts: errors=remount-ro
[ 7.399520] loop: module loaded
[ 9.291659] 8021q: 802.1Q VLAN Support v1.8
[ 9.405106] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.405110] 8021q: adding VLAN 0 to HW filter on device eth0
[ 9.411723] IPv6: ADDRCONF(NETDEV_UP): vlan577: link is not ready
[ 9.905544] IPv6: ADDRCONF(NETDEV_UP): vlan578: link is not ready
[ 10.109084] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
[ 10.212726] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
[ 10.212832] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.418833] e1000e 0000:02:00.1: irq 45 for MSI/MSI-X
[ 10.520423] e1000e 0000:02:00.1: irq 45 for MSI/MSI-X
[ 10.520661] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 10.520664] 8021q: adding VLAN 0 to HW filter on device eth2
[ 10.742526] e1000e 0000:02:00.0: irq 43 for MSI/MSI-X
[ 10.844109] e1000e 0000:02:00.0: irq 43 for MSI/MSI-X
[ 10.844366] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 10.844369] 8021q: adding VLAN 0 to HW filter on device eth3
[ 11.038276] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.224025] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 12.487517] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 12.487864] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.488131] IPv6: ADDRCONF(NETDEV_CHANGE): vlan577: link becomes ready
[ 12.488144] IPv6: ADDRCONF(NETDEV_CHANGE): vlan578: link becomes ready
[ 12.842964] e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 12.843106] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[ 12.846951] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 12.847087] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 13.778144] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 13.778180] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 37.927066] e1000e 0000:00:19.0 eth1: Detected Hardware Unit Hang:
[ 37.927066] TDH <0>
[ 37.927066] TDT <1>
[ 37.927066] next_to_use <1>
[ 37.927066] next_to_clean <0>
[ 37.927066] buffer_info[next_to_clean]:
[ 37.927066] time_stamp <fffefdfb>
[ 37.927066] next_to_watch <0>
[ 37.927066] jiffies <fffefff4>
[ 37.927066] next_to_watch.status <0>
[ 37.927066] MAC Status <40080080>
[ 37.927066] PHY Status <7949>
[ 37.927066] PHY 1000BASE-T Status <0>
[ 37.927066] PHY Extended Status <3000>
[ 37.927066] PCI Status <10>
[ 38.466346] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 38.518087] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 38.929629] e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 39.085586] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 39.496650] e1000e: eth1 NIC Link is Down
[ 42.526255] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 1132.371835] e1000e: eth1 NIC Link is Down
[ 1133.286690] e1000e: eth0 NIC Link is Down
[ 1136.780033] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 1141.703243] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 1198.018424] e1000e: eth0 NIC Link is Down
[ 1198.853870] e1000e: eth1 NIC Link is Down
[ 1201.667745] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
** Model information
sys_vendor: Supermicro�
product_name: X9SCL/X9SCM�
product_version: 0123456789�
chassis_vendor: Supermicro��
chassis_version: 0123456789��
bios_vendor: American Megatrends Inc.
bios_version: 2.0c
board_vendor: Supermicro�
board_name: X9SCL/X9SCMF
board_version: 1.11A���ptal(
** Loaded modules:
xt_nat
iptable_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_nat_ipv4
nf_nat
nf_conntrack
xt_DSCP
iptable_mangle
xt_tcpudp
ipt_REJECT
iptable_filter
ip_tables
x_tables
8021q
garp
stp
mrp
llc
loop
x86_pkg_temp_thermal
intel_powerclamp
coretemp
kvm_intel
kvm
crct10dif_pclmul
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
aesni_intel
aes_x86_64
lrw
gf128mul
glue_helper
ablk_helper
iTCO_wdt
cryptd
joydev
iTCO_vendor_support
ipmi_si
hid_generic
ipmi_msghandler
snd_pcm
snd_page_alloc
button
snd_timer
video
lpc_ich
usbhid
snd
hid
mfd_core
soundcore
processor
pcspkr
i2c_i801
i2c_core
evdev
ext4
crc16
mbcache
jbd2
dm_mod
raid1
md_mod
sg
sd_mod
crc_t10dif
crct10dif_common
ahci
libahci
libata
scsi_mod
ehci_pci
ehci_hcd
usbcore
usb_common
thermal
fan
thermal_sys
e1000e
ptp
pps_core
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
vlan578: 13127313573 11649722 0 0 0 0 0 0 2836890606 9036824 0 0 0 0 0 0
vlan577: 26443792372 26552400 0 0 0 0 0 0 12992451386 30046229 0 0 0 0 0 0
eth0: 40726988567 43200656 0 0 0 0 0 116 16169619872 39235545 0 0 0 0 0 0
eth1: 10404 153 0 0 0 0 0 0 33536 524 0 0 0 0 0 0
eth2: 11189511694 21731372 0 0 0 0 0 0 17284719171 21304406 0 0 0 0 0 0
eth3: 5002262115 19181172 0 3 0 0 0 0 23275054338 21905302 0 0 0 0 0 0
lo: 404774 3693 0 0 0 0 0 0 404774 3693 0 0 0 0 0 0
*** Protocol statistics:
Ip:
78781396 total packets received
5356 with invalid headers
77115762 forwarded
0 incoming packets discarded
167371 incoming packets delivered
77321954 requests sent out
2 outgoing packets dropped
319373 dropped because of missing route
199 fragments dropped after timeout
239480 reassemblies required
119534 packets reassembled ok
209 packet reassembles failed
331 fragments received ok
5 fragments failed
777 fragments created
Icmp:
13906 ICMP messages received
21 input ICMP message failed.
InCsumErrors: 8
ICMP input histogram:
destination unreachable: 1686
timeout in transit: 200
redirects: 2
echo requests: 3833
echo replies: 8177
52684 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 34376
time exceeded: 3816
redirect: 22
echo request: 10436
echo replies: 3802
IcmpMsg:
InType0: 8177
InType3: 1686
InType5: 2
InType8: 3833
InType11: 200
OutType0: 3802
OutType3: 34376
OutType5: 22
OutType8: 10436
OutType11: 3816
OutType69: 232
Tcp:
186 active connections openings
63 passive connection openings
27 failed connection attempts
5 connection resets received
8 connections established
17557 segments received
17571 segments send out
95 segments retransmited
0 bad segments received.
63 resets sent
Udp:
133660 packets received
236 packets to unknown port received.
0 packet receive errors
136401 packets sent
UdpLite:
TcpExt:
8 resets received for embryonic SYN_RECV sockets
177 TCP sockets finished time wait in fast timer
1410 delayed acks sent
1 delayed acks further delayed because of locked socket
Quick ack mode was activated 14 times
17 SYNs to LISTEN sockets dropped
3 packets directly queued to recvmsg prequeue.
3 bytes directly received in process context from prequeue
9973 packet headers predicted
1497 acknowledgments not containing data payload received
895 predicted acknowledgments
3 congestion windows recovered without slow start after partial ack
47 other TCP timeouts
TCPLossProbes: 18
TCPLossProbeRecovery: 7
14 DSACKs sent for old packets
7 DSACKs received
4 connections reset due to unexpected data
1 connections reset due to early user close
1 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 5
TCPSackShiftFallback: 2
TCPDeferAcceptDrop: 48
TCPRcvCoalesce: 4818
TCPOFOQueue: 542
TCPChallengeACK: 1
TCPSpuriousRtxHostQueues: 4
IpExt:
InNoRoutes: 1372955
InTruncatedPkts: 1
InBcastPkts: 2047
InOctets: -821501342
OutOctets: -1994312109
InBcastOctets: 594066
InNoECTPkts: 83874068
InECT1Pkts: 170
InECT0Pkts: 57058
InCEPkts: 1446
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 Processor Family DRAM Controller [8086:0108] (rev 09)
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Super Micro Computer Inc Device [15d9:0624]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4161
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x8, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending+ InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0105] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dfa00000-dfafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Super Micro Computer Inc Device [15d9:0624]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x8, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=03 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:1502]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at dfb00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at dfb25000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f020 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4182
Capabilities: [e0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dfb24000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train+ SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:0624]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df900000-df9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:0624]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at dfb23000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
Memory behind bridge: df000000-df8fffff
Prefetchable memory behind bridge: 00000000de000000-00000000deffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Device [15d9:0624]
00:1f.0 ISA bridge [0601]: Intel Corporation C204 Chipset Family LPC Controller [8086:1c54] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f000 [size=32]
Region 5: Memory at dfb22000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41d1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at dfb21000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0580 [size=32]
Kernel driver in use: i801_smbus
02:00.0 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Dual Port Server Adapter [8086:135e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at dfa60000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at dfa40000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e020 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0100c Data: 41c2
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-15-17-ff-ff-2d-3a-3c
Kernel driver in use: e1000e
02:00.1 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Dual Port Server Adapter [8086:135e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 45
Region 0: Memory at dfa20000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at dfa00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0200c Data: 41a2
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-15-17-ff-ff-2d-3a-3c
Kernel driver in use: e1000e
04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Super Micro Computer Inc Device [15d9:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df900000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=32]
Region 3: Memory at df920000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-57-6d-06
Kernel driver in use: e1000e
05:03.0 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device [15d9:0624]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at df800000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
** USB devices:
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0557:2221 ATEN International Co., Ltd Winbond Hermon
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.12-1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.12-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.52
ii initramfs-tools [linux-initramfs-tool] 0.115
ii kmod 16-2
ii linux-base 3.5
ii module-init-tools 16-2
Versions of packages linux-image-3.12-1-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.12-1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.00-22
pn linux-doc-3.12 <none>
Versions of packages linux-image-3.12-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.40
ii firmware-linux-nonfree 0.40
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.12-1-amd64/postinst/depmod-error-initrd-3.12-1-amd64: false
linux-image-3.12-1-amd64/prerm/removing-running-kernel-3.12-1-amd64: true
--- End Message ---