--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.16.0-0.bpo.4-686-pae: high package loss and data corruption with e1000e driver
- From: Uwe Storbeck <uwe@ibr.ch>
- Date: Wed, 11 Feb 2015 14:18:32 +0100
- Message-id: <20150211131832.29589.75758.reportbug@c1.local.lan>
Package: src:linux
Version: 3.16.7-ckt2-1~bpo70+1
Severity: important
Dear Maintainer,
after switching to kernel 3.16 from backports network packets
over the on-board ethernet controller (Intel Corporation 82566DM
Gigabit Network Connection, driver e1000e) are only transferred
in bursts, transfer rates are below 1 MB/s, packet loss is at 70
to 80%, transferred files are corrupted and I get a lot of kernel
errors (see below).
Switching back to kernel linux-image-3.2.0-4-686-pae fixes the
problem.
Regards
Uwe
-- Package-specific info:
** Kernel log: boot messages should be attached
Feb 11 05:05:02 c1 kernel: [4667586.001612] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:02 c1 kernel: [4667586.001612] TDH <ab>
Feb 11 05:05:02 c1 kernel: [4667586.001612] TDT <11>
Feb 11 05:05:02 c1 kernel: [4667586.001612] next_to_use <11>
Feb 11 05:05:02 c1 kernel: [4667586.001612] next_to_clean <ab>
Feb 11 05:05:02 c1 kernel: [4667586.001612] buffer_info[next_to_clean]:
Feb 11 05:05:02 c1 kernel: [4667586.001612] time_stamp <458c46a8>
Feb 11 05:05:02 c1 kernel: [4667586.001612] next_to_watch <b0>
Feb 11 05:05:02 c1 kernel: [4667586.001612] jiffies <458c487d>
Feb 11 05:05:02 c1 kernel: [4667586.001612] next_to_watch.status <0>
Feb 11 05:05:02 c1 kernel: [4667586.001612] MAC Status <802a3>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY Status <792d>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY 1000BASE-T Status <3800>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY Extended Status <3000>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PCI Status <10>
Feb 11 05:05:04 c1 kernel: [4667588.001373] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:04 c1 kernel: [4667588.001373] TDH <ab>
Feb 11 05:05:04 c1 kernel: [4667588.001373] TDT <11>
Feb 11 05:05:04 c1 kernel: [4667588.001373] next_to_use <11>
Feb 11 05:05:04 c1 kernel: [4667588.001373] next_to_clean <ab>
Feb 11 05:05:04 c1 kernel: [4667588.001373] buffer_info[next_to_clean]:
Feb 11 05:05:04 c1 kernel: [4667588.001373] time_stamp <458c46a8>
Feb 11 05:05:04 c1 kernel: [4667588.001373] next_to_watch <b0>
Feb 11 05:05:04 c1 kernel: [4667588.001373] jiffies <458c4a71>
Feb 11 05:05:04 c1 kernel: [4667588.001373] next_to_watch.status <0>
Feb 11 05:05:04 c1 kernel: [4667588.001373] MAC Status <802a3>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY Status <792d>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY 1000BASE-T Status <3800>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY Extended Status <3000>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PCI Status <10>
Feb 11 05:05:06 c1 kernel: [4667590.000645] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:06 c1 kernel: [4667590.000645] TDH <ab>
Feb 11 05:05:06 c1 kernel: [4667590.000645] TDT <11>
Feb 11 05:05:06 c1 kernel: [4667590.000645] next_to_use <11>
Feb 11 05:05:06 c1 kernel: [4667590.000645] next_to_clean <ab>
Feb 11 05:05:06 c1 kernel: [4667590.000645] buffer_info[next_to_clean]:
Feb 11 05:05:06 c1 kernel: [4667590.000645] time_stamp <458c46a8>
Feb 11 05:05:06 c1 kernel: [4667590.000645] next_to_watch <b0>
Feb 11 05:05:06 c1 kernel: [4667590.000645] jiffies <458c4c65>
Feb 11 05:05:06 c1 kernel: [4667590.000645] next_to_watch.status <0>
Feb 11 05:05:06 c1 kernel: [4667590.000645] MAC Status <802a3>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY Status <792d>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY 1000BASE-T Status <3800>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY Extended Status <3000>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PCI Status <10>
Feb 11 05:05:08 c1 kernel: [4667592.000580] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:08 c1 kernel: [4667592.000580] TDH <ab>
Feb 11 05:05:08 c1 kernel: [4667592.000580] TDT <11>
Feb 11 05:05:08 c1 kernel: [4667592.000580] next_to_use <11>
Feb 11 05:05:08 c1 kernel: [4667592.000580] next_to_clean <ab>
Feb 11 05:05:08 c1 kernel: [4667592.000580] buffer_info[next_to_clean]:
Feb 11 05:05:08 c1 kernel: [4667592.000580] time_stamp <458c46a8>
Feb 11 05:05:08 c1 kernel: [4667592.000580] next_to_watch <b0>
Feb 11 05:05:08 c1 kernel: [4667592.000580] jiffies <458c4e59>
Feb 11 05:05:08 c1 kernel: [4667592.000580] next_to_watch.status <0>
Feb 11 05:05:08 c1 kernel: [4667592.000580] MAC Status <802a3>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY Status <792d>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY 1000BASE-T Status <3800>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY Extended Status <3000>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PCI Status <10>
Feb 11 05:05:08 c1 kernel: [4667592.013550] e1000e 0000:00:19.0 lan: Reset adapter unexpectedly
Feb 11 05:05:11 c1 kernel: [4667594.823364] e1000e: lan NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
** Model information
HP Compaq dc7700p Convertible Minitower
** Network interface configuration:
auto lan
iface lan inet static
address 172.18.1.1
network 172.18.1.0
netmask 255.255.255.128
broadcast 172.18.1.127
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82Q963/Q965 Memory Controller Hub [8086:2990] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82Q963/Q965 Integrated Graphics Controller [8086:2992] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at f0400000 (32-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 2110 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:03.0 Communication controller [0780]: Intel Corporation 82Q963/Q965 HECI Controller [8086:2994] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0526900 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:03.2 IDE interface [0101]: Intel Corporation 82Q963/Q965 PT IDER Controller [8086:2996] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 2118 [size=8]
Region 1: I/O ports at 2140 [size=4]
Region 2: I/O ports at 2120 [size=8]
Region 3: I/O ports at 2144 [size=4]
Region 4: I/O ports at 20e0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_generic
00:03.3 Serial controller [0700]: Intel Corporation 82Q963/Q965 KT Controller [8086:2997] (rev 02) (prog-if 02 [16550])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 2128 [size=8]
Region 1: Memory at f0524000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM Gigabit Network Connection [8086:104a] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2800]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: Memory at f0500000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f0525000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 2000 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 2020 [size=32]
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f0526000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
Subsystem: Hewlett-Packard Company HP Compaq dc7700p [103c:2802]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0520000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8100000-f82fffff
Prefetchable memory behind bridge: 00000000f8300000-00000000f84fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 2060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 2080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0526400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0600000-f08fffff
Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HO (ICH8DO) LPC Interface Controller [8086:2814] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4 port SATA Controller [IDE mode] [8086:2820] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:2802]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 20f0 [size=16]
Region 5: I/O ports at 2100 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
07:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648] (rev 10)
Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0800000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at f8080000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: tg3
07:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648] (rev 10)
Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at f0810000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
07:09.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3512 SATARaid Controller [1095:6512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1030 [size=8]
Region 1: I/O ports at 1040 [size=4]
Region 2: I/O ports at 1038 [size=8]
Region 3: I/O ports at 1044 [size=4]
Region 4: I/O ports at 1020 [size=16]
Region 5: Memory at f0820000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at f8000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
07:0b.0 Network controller [0280]: AVM GmbH A1 ISDN [Fritz] [1244:0a00] (rev 02)
Subsystem: AVM GmbH FRITZ!Card ISDN Controller [1244:0a00]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0820200 (32-bit, non-prefetchable) [size=32]
Region 1: I/O ports at 1000 [size=32]
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 7.8
APT prefers stable
APT policy: (850, 'stable'), (840, 'stable-updates')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-4-686-pae (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.16.0-0.bpo.4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.115~bpo70+1
ii kmod 9-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-0.bpo.4-686-pae recommends:
ii firmware-linux-free 3.2
pn irqbalance <none>
ii libc6-i686 2.13-38+deb7u7
Versions of packages linux-image-3.16.0-0.bpo.4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-0.bpo.4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-0.bpo.4-686-pae/postinst/depmod-error-initrd-3.16.0-0.bpo.4-686-pae: false
linux-image-3.16.0-0.bpo.4-686-pae/prerm/removing-running-kernel-3.16.0-0.bpo.4-686-pae: true
linux-image-3.16.0-0.bpo.4-686-pae/postinst/mips-initrd-3.16.0-0.bpo.4-686-pae:
--- End Message ---