[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#708757: marked as done (linux-image-3.2.0-4-amd64: via-rhine network card fails to initialise correctly)

Your message dated Sat, 24 Apr 2021 08:35:27 -0700 (PDT)
with message-id <60843abf.1c69fb81.8e073.9bc9@mx.google.com>
and subject line Closing this bug (BTS maintenance for src:linux bugs)
has caused the Debian Bug report #708757,
regarding linux-image-3.2.0-4-amd64: via-rhine network card fails to initialise correctly
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
708757: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=708757
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: src:linux
Version: 3.2.41-2+deb7u2
Severity: normal

soekris lan1741 4port pci via-rhine card does not initialise correctly.  MAC
addresses are not found.  Sometimes one mac address is correctly found and then
that port will work.



-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.41-2+deb7u2

** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=f01a829b-4553-4361-a6b8-106f09426ea5 ro quiet

** Tainted: W (512)
 * Taint on warning.

** Kernel log:
[  129.749426] eth2: no IPv6 routers present
[  138.851897] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  138.853045] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  138.853186] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  138.859112] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  138.859223] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  138.865097] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  154.819250] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  154.819450] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  154.825809] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  172.782328] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  172.783554] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  172.784770] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  172.784962] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  172.791212] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  172.791385] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  172.797661] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  172.797865] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  172.804141] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  176.774129] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  176.775377] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  176.776609] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  176.776730] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  176.783022] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  176.783139] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  176.789382] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  176.789503] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  176.795908] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  178.329704] eth0: no IPv6 routers present
[  178.736876] eth1: no IPv6 routers present
[  178.768825] eth2: no IPv6 routers present
[  206.712701] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  206.712811] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  206.719115] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  208.708607] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  208.708724] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  208.714998] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  426.261917] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  426.262037] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  426.268036] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  518.073472] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  518.074602] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  518.075729] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  518.075850] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  518.081672] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  518.081790] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  518.087573] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  518.087735] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  518.093533] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  522.065270] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  522.066399] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  522.067527] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  522.067645] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  522.073459] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  522.073568] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  522.079588] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  522.079749] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  522.085554] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  523.405393] eth1: no IPv6 routers present
[  523.549090] eth2: no IPv6 routers present
[  523.932307] eth0: no IPv6 routers present
[  548.012014] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  548.012138] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  548.017928] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  550.007917] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  550.008041] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  550.013827] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  565.975140] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  565.975269] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  565.981052] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  567.971046] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  567.972175] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  567.972286] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  567.978090] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  567.978200] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  567.983975] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  569.966962] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  569.967089] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  569.972866] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  571.962858] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  571.964054] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  571.964253] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  571.970189] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  571.970309] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  571.976079] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  572.328971] eth1: no IPv6 routers present
[  572.728146] eth0: no IPv6 routers present
[  572.919757] eth2: no IPv6 routers present
[  573.958751] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  573.958878] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  573.964661] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  613.876823] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[  613.877961] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting...
[  613.878069] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[  613.884110] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  613.884260] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder.
[  613.890361] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[  615.872815] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[  615.872989] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder.
[  615.879085] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF

** Model information
sys_vendor:         
product_name:         
product_version:         
chassis_vendor:         
chassis_version:         
bios_vendor: Intel Corp.
bios_version: MUCDT10N.86A.0075.2013.0427.1548
board_vendor: Intel Corporation
board_name: D2700DC 
board_version: AAG32420-602

** Loaded modules:
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
rfkill
binfmt_misc
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
loop
gma500_gfx
snd_hda_codec_realtek
drm_kms_helper
snd_hda_codec_hdmi
drm
i2c_i801
i2c_algo_bit
iTCO_wdt
i2c_core
iTCO_vendor_support
pcspkr
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
evdev
psmouse
serio_raw
snd_seq
snd_seq_device
snd_timer
coretemp
snd
shpchp
soundcore
video
processor
button
thermal_sys
ext4
crc16
jbd2
mbcache
sg
sd_mod
crc_t10dif
usbhid
hid
usb_storage
via_rhine
mii
ahci
libahci
uhci_hcd
libata
scsi_mod
ehci_hcd
e1000e
usbcore
usb_common

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller [8086:0bf3] (rev 03)
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller [8086:0be2] (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 46
	Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=1M]
	Region 1: I/O ports at 30d0 [size=8]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: gma500

00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 45
	Region 0: Memory at 80400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: 80100000-801fffff
	Prefetchable memory behind bridge: 0000000080500000-00000000806fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 4: I/O ports at 30a0 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 3080 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at 3060 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 16
	Region 4: I/O ports at 3040 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at 80304400 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: 80000000-800fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>

00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0])
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 44
	Region 0: I/O ports at 30c8 [size=8]
	Region 1: I/O ports at 30dc [size=4]
	Region 2: I/O ports at 30c0 [size=8]
	Region 3: I/O ports at 30d8 [size=4]
	Region 4: I/O ports at 3020 [size=16]
	Region 5: Memory at 80304000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ahci

00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02)
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 3000 [size=32]
	Kernel driver in use: i801_smbus

01:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
	Subsystem: Intel Corporation Device [8086:2011]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at 80120000 (32-bit, non-prefetchable) [size=128K]
	Region 1: Memory at 80100000 (32-bit, non-prefetchable) [size=128K]
	Region 2: I/O ports at 2000 [size=32]
	Region 3: Memory at 80140000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: e1000e

02:00.0 PCI bridge [0604]: Texas Instruments PCI2250 PCI-to-PCI Bridge [104c:ac23] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: 80000000-800fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

03:00.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
	Subsystem: VIA Technologies, Inc. Device [1106:0106]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: I/O ports at 1300 [size=256]
	Region 1: Memory at 80000300 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: via-rhine

03:01.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
	Subsystem: VIA Technologies, Inc. Device [1106:0106]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at 1200 [size=256]
	Region 1: Memory at 80000200 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: via-rhine

03:02.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
	Subsystem: VIA Technologies, Inc. Device [1106:0106]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 22
	Region 0: I/O ports at 1100 [size=256]
	Region 1: Memory at 80000100 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: via-rhine

03:03.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
	Subsystem: VIA Technologies, Inc. Device [1106:0106]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 23
	Region 0: I/O ports at 1000 [size=256]
	Region 1: Memory at 80000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: via-rhine


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
Bus 003 Device 002: ID 046d:c019 Logitech, Inc. Optical Tilt Wheel Mouse
Bus 004 Device 002: ID 046d:c315 Logitech, Inc. Classic New Touch Keyboard


-- System Information:
Debian Release: 7.0
  APT prefers stable-updates
  APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii  debconf [debconf-2.0]                   1.5.49
ii  initramfs-tools [linux-initramfs-tool]  0.109.1
ii  kmod                                    9-3
ii  linux-base                              3.5
ii  module-init-tools                       9-3

Versions of packages linux-image-3.2.0-4-amd64 recommends:
pn  firmware-linux-free  <none>

Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 1.99-27+deb7u1
pn  linux-doc-3.2           <none>

Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      <none>
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-libertas       <none>
pn  firmware-linux          <none>
pn  firmware-linux-nonfree  <none>
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information:
  linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
  linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
  linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
  linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:

--- End Message ---
--- Begin Message --- 
Hi

This bug was filed for a very old kernel or the bug is old itself
without resolution.

If you can reproduce it with

- the current version in unstable/testing
- the latest kernel from backports

please reopen the bug, see https://www.debian.org/Bugs/server-control
for details.

Regards,
Salvatore

--- End Message ---
Reply to: