Bug#968109: linux-image-5.7.0-2-arm64: USB unusable on Raspberry Pi 4B 8GB
Package: src:linux
Version: 5.7.10-1
Severity: normal
Dear Maintainer,
I installed an SD card image from
https://raspi.debian.net/daily/raspi_4.img.xz
to Raspberry Pi 4B 8GB (board revision 1.4).
USB is unusable and "lsusb" shows nothing.
Relevant dmesg is as follows:
[ 3.198861] pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 8.663493] pci 0000:01:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x801
[ 8.663690] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x890 took 5336734 usecs
[ 12.265387] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 12.268816] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[ 12.278041] dwc2 fe980000.usb: supply vusb_d not found, using dummy regulator
[ 12.278134] dwc2 fe980000.usb: supply vusb_a not found, using dummy regulator
[ 12.282227] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 22.320273] xhci_hcd 0000:01:00.0: can't setup: -110
[ 22.336521] xhci_hcd 0000:01:00.0: USB bus 1 deregistered
[ 22.353573] xhci_hcd 0000:01:00.0: init 0000:01:00.0 fail, -110
Best regards, Ryutaroh Matsumoto
-- Package-specific info:
** Version:
Linux version 5.7.0-2-arm64 (debian-kernel@lists.debian.org) (gcc version 9.3.0 (Debian 9.3.0-15), GNU ld (GNU Binutils for Debian) 2.35) #1 SMP Debian 5.7.10-1 (2020-07-26)
** Command line:
video=HDMI-A-1:3840x2160M@30,margin_left=48,margin_right=48,margin_top=48,margin_bottom=48 dma.dmachans=0x71f5 bcm2709.boardrev=0xd03114 bcm2709.serial=0x488d2af3 bcm2709.uart_clock=48000000 bcm2709.disk_led_gpio=42 bcm2709.disk_led_active_low=0 smsc95xx.macaddr=DC:A6:32:BB:99:D9 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=tty0 console=ttyS1,115200 root=/dev/mmcblk1p2 rw elevator=deadline fsck.repair=yes net.ifnames=0 rootwait
** Tainted: C (1024)
* staging driver was loaded
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
Device Tree model: Raspberry Pi 4 Model B Rev 1.4
** Loaded modules:
nls_ascii
nls_cp437
vfat
fat
hci_uart
btqca
btrtl
btbcm
btsdio
btintel
bcm2835_v4l2(C)
bluetooth
brcmfmac
brcmutil
videobuf2_vmalloc
videobuf2_memops
snd_bcm2835(C)
videobuf2_v4l2
jitterentropy_rng
videobuf2_common
snd_pcm
drbg
snd_timer
videodev
snd
ansi_cprng
cpufreq_dt
cfg80211
mc
soundcore
ecdh_generic
ecc
rfkill
raspberrypi_cpufreq
bcm2835_wdt
bcm2711_thermal
pwm_bcm2835
iproc_rng200
vchiq(C)
rng_core
leds_gpio
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
btrfs
blake2b_generic
xor
xor_neon
zstd_decompress
zstd_compress
raid6_pq
libcrc32c
crc32c_generic
bfq
broadcom
bcm_phy_lib
xhci_pci
dwc2
xhci_hcd
udc_core
mdio_bcm_unimac
usbcore
genet
sdhci_iproc
of_mdio
sdhci_pltfm
i2c_bcm2835
fixed_phy
libphy
sdhci
gpio_regulator
usb_common
phy_generic
** Network interface configuration:
*** /etc/network/interfaces:
# interfaces(5) file used by ifup(8) and ifdown(8)
# Include files from /etc/network/interfaces.d:
source-directory /etc/network/interfaces.d
*** /etc/network/interfaces.d/eth0:
auto eth0
# TODO: switch back to iptables-persistent once it re-enters testing
iface eth0 inet dhcp
# We don't currently support setup of firewalls here.
# pre-up iptables-restore < /etc/iptables/rules.v4 || true
# pre-up ip6tables-restore < /etc/iptables/rules.v6 || ture
*** /etc/network/interfaces.d/wlan0:
auto wlan0
# TODO: switch back to iptables-persistent once it re-enters testing
iface wlan0 inet dhcp
# We don't currently support setup of firewalls here.
# pre-up iptables-restore < /etc/iptables/rules.v4 || true
# pre-up ip6tables-restore < /etc/iptables/rules.v6 || ture
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether dc:a6:32:bb:99:d9 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether dc:a6:32:bb:99:da brd ff:ff:ff:ff:ff:ff
inet 192.168.1.84/24 brd 192.168.1.255 scope global dynamic wlan0
valid_lft 42924sec preferred_lft 42924sec
inet6 2400:4050:2ba1:ac00:dea6:32ff:febb:99da/64 scope global dynamic mngtmpaddr
valid_lft 14071sec preferred_lft 12271sec
inet6 fe80::dea6:32ff:febb:99da/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
wlan0: 281488 1123 0 0 0 0 0 5 127586 832 0 0 0 0 0 0
** PCI devices:
00:00.0 PCI bridge [0604]: Broadcom Limited Device [14e4:2711] (rev 10) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: f8000000-f80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [ac] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <2us
ClockPM+ Surprise- LLActRep- BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible+
RootCap: CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via WAKE# ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [180 v1] Vendor Specific Information: ID=0000 Rev=0 Len=028 <?>
Capabilities: [240 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=8us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=1us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
Kernel driver in use: pcieport
01:00.0 USB controller [0c03]: VIA Technologies, Inc. VL805 USB 3.0 Host Controller [1106:3483] (rev 01) (prog-if 30 [XHCI])
Subsystem: VIA Technologies, Inc. VL805 USB 3.0 Host Controller [1106:3483]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 40
Region 0: Memory at 600000000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c4] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel modules: xhci_pci
** USB devices:
not available
-- System Information:
Debian Release: 10.5
APT prefers stable
APT policy: (990, 'stable'), (500, 'stable-updates'), (500, 'unstable')
Architecture: arm64 (aarch64)
Kernel: Linux 5.7.0-2-arm64 (SMP w/4 CPU cores)
Kernel taint flags: TAINT_CRAP
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-5.7.0-2-arm64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.137
ii kmod 26-1
ii linux-base 4.6
Versions of packages linux-image-5.7.0-2-arm64 recommends:
ii apparmor 2.13.2-10
ii firmware-linux-free 3.4
Versions of packages linux-image-5.7.0-2-arm64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-5.7 <none>
Versions of packages linux-image-5.7.0-2-arm64 is related to:
ii firmware-amd-graphics 20200619-1
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
ii firmware-brcm80211 20190114-2
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux-nonfree 20200619-1
ii firmware-misc-nonfree 20200619-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: