Bug#974921: linux-image-5.9.0-2-arm64: Could you consider CONFIG_VDPA=m and CONFIG_VFIO_MDEV=m ?
Package: src:linux
Version: 5.9.6-1
Severity: wishlist
Dear Maintainer,
vDPA means virtio data path acceleration, and a faster alternative
to vhost-net. Its advantages over vhost-net is explained at
https://www.redhat.com/ja/blog/introduction-vdpa-kernel-framework
MDEV means mediator devices, and its use cases are explained at
https://www.redhat.com/en/blog/how-deep-does-vdpa-rabbit-hole-go
and can conveniently used with vDPA above.
Both of them are currently disabled at the Debian kernel package.
I would appreciate it if you could consider enabling them as modules.
Best regards, Ryutaroh Matsumoto
-- Package-specific info:
** Version:
Linux version 5.9.0-2-arm64 (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.0-16) 10.2.0, GNU ld (GNU Binutils for Debian) 2.35.1) #1 SMP Debian 5.9.6-1 (2020-11-08)
** Command line:
video=HDMI-A-1:3840x2160M@30,margin_left=48,margin_right=48,margin_top=48,margin_bottom=48 dma.dmachans=0x71f5 bcm2709.boardrev=0xd03114 bcm2709.serial=0x488d2af3 bcm2709.uart_clock=48000000 bcm2709.disk_led_gpio=42 bcm2709.disk_led_active_low=0 smsc95xx.macaddr=DC:A6:32:BB:99:D9 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=tty0 console=ttyS1,115200 root=/dev/mmcblk1p2 rw elevator=deadline fsck.repair=yes net.ifnames=0 rootwait
** Tainted: C (1024)
* staging driver was loaded
** Kernel log:
[ 14.382071] platform regulatory.0: firmware: direct-loading firmware regulatory.db
[ 14.397371] platform regulatory.0: firmware: direct-loading firmware regulatory.db.p7s
[ 14.407069] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
[ 14.467310] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 14.482828] usbcore: registered new interface driver brcmfmac
[ 14.608442] brcmfmac mmc0:0001:1: firmware: direct-loading firmware brcm/brcmfmac43455-sdio.bin
[ 14.626753] brcmfmac mmc0:0001:1: firmware: direct-loading firmware brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.txt
[ 14.757810] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 14.772482] brcmfmac mmc0:0001:1: firmware: failed to load brcm/brcmfmac43455-sdio.clm_blob (-2)
[ 14.787326] firmware_class: See https://wiki.debian.org/Firmware for information about missing firmware
[ 14.813962] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 14.840193] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 1 2015 07:29:38 version 7.45.18 (r538002) FWID 01-6a2c8ad4
[ 14.882902] random: crng init done
[ 14.891827] Bluetooth: Core ver 2.22
[ 14.892590] random: 3 urandom warning(s) missed due to ratelimiting
[ 14.902517] NET: Registered protocol family 31
[ 14.925671] Bluetooth: HCI device and connection manager initialized
[ 14.938656] Bluetooth: HCI socket layer initialized
[ 14.952837] Bluetooth: L2CAP socket layer initialized
[ 14.968934] Bluetooth: SCO socket layer initialized
[ 15.004369] input: SEM USB Keyboard as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:1A2C:4324.0001/input/input0
[ 15.047674] mc: Linux media interface: v0.10
[ 15.086073] hid-generic 0003:1A2C:4324.0001: input,hidraw0: USB HID v1.10 Keyboard [SEM USB Keyboard] on usb-0000:01:00.0-1.3/input0
[ 15.086465] videodev: Linux video capture interface: v2.00
[ 15.115306] input: SEM USB Keyboard Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1A2C:4324.0002/input/input1
[ 15.165175] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 15.179901] Bluetooth: HCI UART driver ver 2.3
[ 15.187463] Bluetooth: HCI UART protocol H4 registered
[ 15.187665] Bluetooth: HCI UART protocol LL registered
[ 15.195137] input: SEM USB Keyboard System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1A2C:4324.0002/input/input2
[ 15.195289] hid-generic 0003:1A2C:4324.0002: input,hidraw1: USB HID v1.10 Device [SEM USB Keyboard] on usb-0000:01:00.0-1.3/input1
[ 15.196317] input: USB Optical Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:15CA:00C3.0003/input/input3
[ 15.203971] Bluetooth: HCI UART protocol ATH3K registered
[ 15.204259] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 15.206621] bcm2835_audio bcm2835_audio: card created with 8 channels
[ 15.224906] hid-generic 0003:15CA:00C3.0003: input,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:01:00.0-1.4/input0
[ 15.226421] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 15.242364] Bluetooth: HCI UART protocol Intel registered
[ 15.321838] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 15.324663] Bluetooth: HCI UART protocol Broadcom registered
[ 15.346836] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 15.346883] Bluetooth: HCI UART protocol QCA registered
[ 15.346979] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 15.377504] Bluetooth: HCI UART protocol AG6XX registered
[ 15.377669] Bluetooth: HCI UART protocol Marvell registered
[ 15.489171] uart-pl011 fe201000.serial: no DMA platform data
[ 15.587631] audit: type=1400 audit(1605343669.715:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/lxc-start" pid=392 comm="apparmor_parser"
[ 15.608029] audit: type=1400 audit(1605343669.715:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=390 comm="apparmor_parser"
[ 15.627533] audit: type=1400 audit(1605343669.715:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=390 comm="apparmor_parser"
[ 15.647149] audit: type=1400 audit(1605343669.715:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=390 comm="apparmor_parser"
[ 15.666160] audit: type=1400 audit(1605343669.719:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=393 comm="apparmor_parser"
[ 15.685675] audit: type=1400 audit(1605343669.779:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=395 comm="apparmor_parser"
[ 15.705038] audit: type=1400 audit(1605343669.779:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=395 comm="apparmor_parser"
[ 15.725149] audit: type=1400 audit(1605343669.799:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lxc-container-default" pid=391 comm="apparmor_parser"
[ 15.745385] audit: type=1400 audit(1605343669.799:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lxc-container-default-cgns" pid=391 comm="apparmor_parser"
[ 15.766053] audit: type=1400 audit(1605343669.799:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lxc-container-default-with-mounting" pid=391 comm="apparmor_parser"
[ 15.787516] Bluetooth: hci0: BCM: chip id 107
[ 15.795768] Bluetooth: hci0: BCM: features 0x2f
[ 15.805823] Bluetooth: hci0: BCM4345C0
[ 15.813673] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000
[ 15.823855] bluetooth hci0: firmware: failed to load brcm/BCM4345C0.hcd (-2)
[ 15.835070] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2)
[ 15.845804] Bluetooth: hci0: BCM: firmware Patch file not found, tried:
[ 15.856594] Bluetooth: hci0: BCM: 'brcm/BCM4345C0.hcd'
[ 15.865476] Bluetooth: hci0: BCM: 'brcm/BCM.hcd'
[ 17.300565] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 22.404323] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 44.196503] device-mapper: uevent: version 1.0.3
[ 44.201512] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 44.379796] loop: module loaded
[ 44.905336] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[ 2039.901528] fuse: init (API version 7.31)
[ 2886.967576] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[10615.018124] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[13134.111248] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[16125.206163] loop0: p1 p2
[16125.375844] loop0: p1 p2 p3
[16125.521801] loop0: p1 p2 p3
[16127.245066] EXT4-fs (loop0p2): barriers disabled
[16127.251230] EXT4-fs (loop0p2): mounted filesystem with writeback data mode. Opts: discard,nobarrier,commit=3600,delalloc,noauto_da_alloc,data=writeback
[16285.535569] loop0: p1 p2
[16285.697202] loop0: p1 p2 p3
[16285.810106] loop0: p1 p2 p3
[16291.106223] EXT4-fs (loop0p2): barriers disabled
[16291.113667] EXT4-fs (loop0p2): mounted filesystem with writeback data mode. Opts: discard,nobarrier,commit=3600,delalloc,noauto_da_alloc,data=writeback
[17987.351563] loop0: p1 p2
[17987.535869] loop0: p1 p2 p3
[17987.690651] loop0: p1 p2 p3
[17989.267331] BTRFS: device label ROOT devid 1 transid 5 /dev/loop0p2 scanned by mkfs.btrfs (192619)
[17989.335707] BTRFS info (device loop0p2): enabling ssd optimizations
[17989.342262] BTRFS info (device loop0p2): turning on sync discard
[17989.348451] BTRFS info (device loop0p2): enabling auto defrag
[17989.354352] BTRFS info (device loop0p2): turning off barriers
[17989.360261] BTRFS warning (device loop0p2): excessive commit interval 3600
[17989.367316] BTRFS info (device loop0p2): setting incompat feature flag for COMPRESS_LZO (0x8)
[17989.376193] BTRFS info (device loop0p2): force lzo compression, level 0
[17989.382971] BTRFS info (device loop0p2): disk space caching is enabled
[17989.389654] BTRFS info (device loop0p2): has skinny extents
[17989.395355] BTRFS info (device loop0p2): flagging fs with big metadata feature
[17989.405281] BTRFS info (device loop0p2): checking UUID tree
** Model information
Device Tree model: Raspberry Pi 4 Model B Rev 1.4
** Loaded modules:
fuse
ext4
mbcache
jbd2
loop
dm_mod
xt_CHECKSUM
nft_chain_nat
xt_MASQUERADE
nf_nat
nf_conntrack
nf_defrag_ipv6
nf_defrag_ipv4
nft_counter
xt_tcpudp
nft_compat
bridge
stp
llc
nf_tables
nfnetlink
binfmt_misc
bcm2835_v4l2(C)
nls_ascii
joydev
nls_cp437
evdev
vfat
fat
bcm2835_mmal_vchiq(C)
videobuf2_vmalloc
snd_bcm2835(C)
hci_uart
videobuf2_memops
snd_pcm
videobuf2_v4l2
btqca
videobuf2_common
snd_timer
btrtl
snd
videodev
btbcm
btintel
btsdio
mc
soundcore
hid_generic
cpufreq_dt
bluetooth
jitterentropy_rng
brcmfmac
drbg
brcmutil
aes_arm64
aes_generic
ansi_cprng
cfg80211
ecdh_generic
usbhid
ecc
hid
crc16
libaes
raspberrypi_cpufreq
rfkill
bcm2711_thermal
bcm2835_wdt
pwm_bcm2835
iproc_rng200
vchiq(C)
rng_core
leds_gpio
vhost_net
tun
vhost
vhost_iotlb
tap
bfq
drm
ip_tables
x_tables
autofs4
btrfs
xor
xor_neon
zstd_compress
raid6_pq
crc32c_generic
libcrc32c
broadcom
bcm_phy_lib
dwc2
xhci_pci
xhci_hcd
udc_core
mdio_bcm_unimac
usbcore
usb_common
sdhci_iproc
sdhci_pltfm
genet
i2c_bcm2835
of_mdio
sdhci
fixed_phy
libphy
phy_generic
gpio_regulator
fixed
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether dc:a6:32:bb:99:d9 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether dc:a6:32:bb:99:da brd ff:ff:ff:ff:ff:ff
inet 192.168.1.9/24 brd 192.168.1.255 scope global wlan0
valid_lft forever preferred_lft forever
inet6 fe80::dea6:32ff:febb:99da/64 scope link
valid_lft forever preferred_lft forever
4: lxcbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
link/ether 00:16:3e:00:00:00 brd ff:ff:ff:ff:ff:ff
inet 10.0.3.1/24 brd 10.0.3.255 scope global lxcbr0
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 769278117 319622 0 0 0 0 0 0 769278117 319622 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
wlan0: 1064422258 819818 0 0 0 0 0 1673 45625898 307370 0 0 0 0 0 0
lxcbr0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
** PCI devices:
00:00.0 PCI bridge [0604]: Broadcom Inc. and subsidiaries Device [14e4:2711] (rev 10) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff [size=4K]
Memory behind bridge: f8000000-f80fffff [size=1M]
Prefetchable memory behind bridge: [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [ac] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <2us
ClockPM+ Surprise- LLActRep- BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
RootCap: CRSVisible+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS+
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported, DRS-
DownstreamComp: Link Down - Not Determined
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Capabilities: [180 v1] Vendor Specific Information: ID=0000 Rev=0 Len=028 <?>
Capabilities: [240 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=8us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=1us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
Kernel driver in use: pcieport
01:00.0 USB controller [0c03]: VIA Technologies, Inc. VL805 USB 3.0 Host Controller [1106:3483] (rev 01) (prog-if 30 [XHCI])
Subsystem: VIA Technologies, Inc. VL805 USB 3.0 Host Controller [1106:3483]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at 600000000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/4 Maskable- 64bit+
Address: 0000000ffffffffc Data: 6540
Capabilities: [c4] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 15ca:00c3 Textech International Ltd. Mini Optical Mouse
Bus 001 Device 003: ID 1a2c:4324 China Resource Semico Co., Ltd USB Keyboard
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: bullseye/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (1, 'experimental')
Architecture: arm64 (aarch64)
Kernel: Linux 5.9.0-2-arm64 (SMP w/4 CPU threads)
Kernel taint flags: TAINT_CRAP
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE not set
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-5.9.0-2-arm64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.139
ii kmod 27+20200310-2
ii linux-base 4.6
Versions of packages linux-image-5.9.0-2-arm64 recommends:
ii apparmor 2.13.5-1
ii firmware-linux-free 20200122-1
Versions of packages linux-image-5.9.0-2-arm64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-5.9 <none>
Versions of packages linux-image-5.9.0-2-arm64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
ii firmware-brcm80211 20200918-1
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
ii firmware-misc-nonfree 20200918-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: