[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#952631: Resuming from hibernation fails using linux-image-4.19.0-8-686-pae and linux-image-4.9.0-12-686-pae (but not linux-



Package: src:linux
Version: 4.19.98-1
Severity: normal



-- Package-specific info:
** Version:
Linux version 4.19.0-8-686-pae (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.98-1 (2020-01-26)

** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.19.0-8-686-pae root=UUID=79bfca72-c003-4dbe-a5ff-ab37d290ac19 ro quiet

** Not tainted

** Kernel log:
Unable to read kernel log; any relevant messages should be attached

** Model information

** Loaded modules:
lib80211_crypt_ccmp
ipw2200
snd_intel8x0
dell_laptop
libipw
snd_intel8x0m
dell_smbios
lib80211
cfg80211
snd_ac97_codec
dell_wmi_descriptor
ac97_bus
wmi
snd_pcm
dcdbas
snd_timer
dell_smm_hwmon
snd
iTCO_wdt
joydev
soundcore
yenta_socket
serio_raw
iTCO_vendor_support
rfkill
pcspkr
sg
pcmcia_rsrc
rng_core
evdev
ac
pcc_cpufreq
battery
acpi_cpufreq
firewire_sbp2
parport_pc
ppdev
lp
parport
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
fscrypto
ecb
crypto_simd
cryptd
aes_i586
sr_mod
cdrom
sd_mod
ata_generic
i915
ata_piix
ahci
libahci
i2c_algo_bit
b44
drm_kms_helper
libata
ssb
mmc_core
uhci_hcd
ehci_pci
ehci_hcd
drm
scsi_mod
mii
usbcore
libphy
psmouse
firewire_ohci
firewire_core
pcmcia
lpc_ich
mfd_core
pcmcia_core
crc_itu_t
usb_common
thermal
button
video

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

source /etc/network/interfaces.d/*

# The loopback network interface
auto lo
iface lo inet loopback

** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether 00:15:c5:06:37:42 brd ff:ff:ff:ff:ff:ff
3: wlp2s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:16:6f:81:fc:45 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.5/24 brd 192.168.1.255 scope global dynamic noprefixroute wlp2s3
       valid_lft 81707sec preferred_lft 81707sec
    inet6 fe80::4852:4d51:9f4d:18b2/64 scope link noprefixroute 
       valid_lft forever preferred_lft forever

*** Device statistics:
Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo frame compressed multicast|bytes    packets errs drop fifo colls carrier compressed
    lo:     396       8    0    0    0     0          0         0      396       8    0    0    0     0       0          0
wlp2s3: 5744474   10278    0    0    0     0          0         0  1514554   10043    0    0    0     0       0          0
  eth0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0


** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 03)
	Subsystem: Dell Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [1028:01af]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 03) (prog-if 00 [VGA controller])
	Subsystem: Dell Mobile 915GM/GMS/910GML Express Graphics Controller [1028:01af]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at ec38 [size=8]
	Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]
	[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: i915
	Kernel modules: i915

00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 03)
	Subsystem: Dell Mobile 915GM/GMS/910GML Express Graphics Controller [1028:01af]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: <access denied>

00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03) (prog-if 00 [UHCI])
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI [1028:01af]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at bf80 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03) (prog-if 00 [UHCI])
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI [1028:01af]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at bf60 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03) (prog-if 00 [UHCI])
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI [1028:01af]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at bf40 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03) (prog-if 00 [UHCI])
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI [1028:01af]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 4: I/O ports at bf20 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03) (prog-if 20 [EHCI])
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [1028:01af]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d3) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: dfd00000-dfdfffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 03)
	Subsystem: Dell 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [1028:01af]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at ed00 [size=256]
	Region 1: I/O ports at ec40 [size=64]
	Region 2: Memory at dfebfe00 (32-bit, non-prefetchable) [size=512]
	Region 3: Memory at dfebfd00 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: snd_intel8x0
	Kernel modules: snd_intel8x0

00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller [8086:266d] (rev 03) (prog-if 00 [Generic])
	Subsystem: Conexant Systems, Inc. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller [14f1:5423]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at ee00 [size=256]
	Region 1: I/O ports at ec80 [size=128]
	Capabilities: <access denied>
	Kernel driver in use: snd_intel8x0m
	Kernel modules: snd_intel8x0m

00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 03)
	Subsystem: Dell 82801FBM (ICH6M) LPC Interface Bridge [1028:01af]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel driver in use: lpc_ich
	Kernel modules: intel_rng, lpc_ich

00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 03) (prog-if 80 [ISA Compatibility mode-only controller, supports bus mastering])
	Subsystem: Dell 82801FBM (ICH6M) SATA Controller [1028:01af]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374
	Region 4: I/O ports at bfa0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ahci, ata_piix, ata_generic

02:00.0 Ethernet controller [0200]: Broadcom Limited BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
	Subsystem: Dell Inspiron 6400 [1028:01af]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at dfdfa000 (32-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: b44
	Kernel modules: b44

02:01.0 CardBus bridge [0607]: Texas Instruments PCI6515 Cardbus Controller [104c:8036]
	Subsystem: Dell PCI6515 Cardbus Controller [1028:01af]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=03, sec-latency=176
	Memory window 0: 84000000-87ffffff (prefetchable)
	Memory window 1: 88000000-8bffffff
	I/O window 0: 00002000-000020ff
	I/O window 1: 00002400-000024ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Capabilities: <access denied>
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

02:01.2 FireWire (IEEE 1394) [0c00]: Texas Instruments Device [104c:8037] (prog-if 10 [OHCI])
	Subsystem: Dell Device [1028:01af]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 18
	Region 0: Memory at dfdf8800 (32-bit, non-prefetchable) [size=2K]
	Region 1: Memory at dfdfc000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: firewire_ohci
	Kernel modules: firewire_ohci

02:03.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
	Subsystem: Intel Corporation Dell Latitude D600 [8086:2722]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (750ns min, 6000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at dfdf9000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: ipw2200
	Kernel modules: ipw2200


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


-- System Information:
Debian Release: 10.3
  APT prefers oldoldstable
  APT policy: (500, 'oldoldstable')
Architecture: i386 (i686)

Kernel: Linux 4.19.0-8-686-pae (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8), LANGUAGE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled

Versions of packages linux-image-4.19.0-8-686-pae depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.133+deb10u1
ii  kmod                                    26-1
ii  linux-base                              4.6

Versions of packages linux-image-4.19.0-8-686-pae recommends:
ii  apparmor             2.13.2-10
ii  firmware-linux-free  3.4

Versions of packages linux-image-4.19.0-8-686-pae suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 2.02+dfsg1-20
pn  linux-doc-4.19          <none>

Versions of packages linux-image-4.19.0-8-686-pae is related to:
pn  firmware-amd-graphics     <none>
pn  firmware-atheros          <none>
pn  firmware-bnx2             <none>
pn  firmware-bnx2x            <none>
pn  firmware-brcm80211        <none>
pn  firmware-cavium           <none>
pn  firmware-intel-sound      <none>
pn  firmware-intelwimax       <none>
pn  firmware-ipw2x00          <none>
pn  firmware-ivtv             <none>
pn  firmware-iwlwifi          <none>
pn  firmware-libertas         <none>
pn  firmware-linux-nonfree    <none>
pn  firmware-misc-nonfree     <none>
pn  firmware-myricom          <none>
pn  firmware-netxen           <none>
pn  firmware-qlogic           <none>
pn  firmware-realtek          <none>
pn  firmware-samsung          <none>
pn  firmware-siano            <none>
pn  firmware-ti-connectivity  <none>
pn  xen-hypervisor            <none>

-- no debconf information

-- additional information from user EinSteiGer:
Using the following kernels resuming from hibernation ends in a black screen and only hold power botton helps:
linux-image-4.19.0-8-686-pae
linux-image-4.9.0-12-686-pae
But it works fine with the following one:
linux-image-3.16.0-10-686-pae

journalctl -f has the following output:
Feb 25 14:11:08 laptop systemd[1]: Starting Hibernate...
Feb 25 14:11:08 laptop systemd[1]: syncthing-resume.service: Succeeded.
Feb 25 14:11:08 laptop systemd[1]: Started Restart Syncthing after resume.
Feb 25 14:11:08 laptop kernel: PM: Image not found (code -22)
Feb 25 14:11:08 laptop systemd-sleep[888]: Suspending system...
Feb 25 14:11:08 laptop kernel: PM: hibernation entry
Feb 25 14:11:08 laptop kernel: PM: Syncing filesystems ... 
-- Reboot --
Feb 25 14:28:28 laptop kernel: Linux version 4.19.0-8-686-pae (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.98-1 (2020-01-26)

Cf. https://debianforum.de/forum/viewtopic.php?f=26&t=176192


Reply to: