[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#931639: linux-image-4.19.0-5-amd64: Does not boot - stuck at "Loading initial ramdisk"



This is proberly linked to this Bug, also coreboot used as firmware on
the affected system:

https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=930029

So its possible that this only apears in the combination linux 4.19 +
coreboot.

With earlyprintk= VALUE as bootparameter you can get more output ouput
the kernel panic / hang

Am 08.07.19 um 17:44 schrieb QWERTY man:
> Package: src:linux
> Version: 4.19.37-5
> Severity: critical
> Justification: breaks the whole system
>
>
> Dear Maintainer,
>
>
>    * What led up to the situation?
>
> Upgraded from a very stable and largely vanilla Debian Stretch to Debian Buster.
>
>
>    * What exactly did you do (or not do) that was effective (or
>      ineffective)?
>    * What was the outcome of this action?
>
> Rebooted, and it entered a loop of the following messages:
>
>   Loading Linux 4.19.0-5-amd64...
>   Loading initial ramdisk
>
>     INFO: task swapper/0:1 blocked for more than 120 secs
>     Not tainted 4.19.0-5-amd64 #1 Debian 4.19.37-5
>     "echo 0 > /proc/sys/kernel/hung_task_timeout_secds" disables this message
>
>     INFO: task cpuhp/0:14 blocked for more than 120 secs
>     Not tainted 4.19.0-5-amd64 #1 Debian 4.19.37-5
>     "echo 0 > /proc/sys/kernel/hung_task_timeout_secds" disables this message
>
> I then booted the system with the 4.9.0-9-amd64 kernel, and everything worked as
> before.
>
> Note that same issue occurs on another system with the same motherboard and
> processor - D945GCLF2B - but different hard drive and PSU: it hangs at boot.
>
>
>    * What outcome did you expect instead?
>
> I imagined Debian stable was uber stable based on past experience.
>
>
>
> -- Package-specific info:
> ** Kernel log: boot messages should be attached
>
> ** Model information
> sys_vendor: Intel
> product_name: D945GCLF  <--  It is actually D945GCLF2B
> product_version: 1.0
> chassis_vendor: Intel
> chassis_version: 
> bios_vendor: coreboot
> bios_version: 382892c
> board_vendor: Intel
> board_name: D945GCLF    <--  Above
> board_version: 1.0
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
> 	Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:464c]
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
> 	Latency: 0
> 	Capabilities: <access denied>
>
> 00:02.0 VGA compatible controller [0300]: Intel Corporation 82945G/GZ Integrated Graphics Controller [8086:2772] (rev 02) (prog-if 00 [VGA controller])
> 	Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller [8086:464c]
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin A routed to IRQ 16
> 	Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=512K]
> 	Region 1: I/O ports at 2080 [size=8]
> 	Region 2: Memory at c0000000 (32-bit, prefetchable) [size=512M]
> 	Region 3: Memory at e0280000 (32-bit, non-prefetchable) [size=512K]
> 	[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
> 	Capabilities: <access denied>
> 	Kernel driver in use: i915
> 	Kernel modules: i915
>
> 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 01)
> 	Subsystem: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:464c]
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0, Cache Line Size: 64 bytes
> 	Interrupt: pin A routed to IRQ 27
> 	Region 0: Memory at e0300000 (64-bit, non-prefetchable) [size=16K]
> 	Capabilities: <access denied>
> 	Kernel driver in use: snd_hda_intel
> 	Kernel modules: snd_hda_intel
>
> 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0, Cache Line Size: 64 bytes
> 	Interrupt: pin A routed to IRQ 24
> 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> 	I/O behind bridge: 00001000-00001fff
> 	Memory behind bridge: e0100000-e01fffff
> 	Prefetchable memory behind bridge: 00000000e0000000-00000000e00fffff
> 	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> 	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> 	Capabilities: <access denied>
> 	Kernel driver in use: pcieport
> 	Kernel modules: shpchp
>
> 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode])
> 	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0, Cache Line Size: 64 bytes
> 	Interrupt: pin C routed to IRQ 25
> 	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> 	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> 	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> 	Capabilities: <access denied>
> 	Kernel driver in use: pcieport
> 	Kernel modules: shpchp
>
> 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
> 	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0, Cache Line Size: 64 bytes
> 	Interrupt: pin D routed to IRQ 26
> 	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
> 	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> 	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> 	Capabilities: <access denied>
> 	Kernel driver in use: pcieport
> 	Kernel modules: shpchp
>
> 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
> 	Subsystem: Intel Corporation NM10/ICH7 Family USB UHCI Controller [8086:464c]
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin A routed to IRQ 23
> 	Region 4: I/O ports at 2000 [size=32]
> 	Kernel driver in use: uhci_hcd
> 	Kernel modules: uhci_hcd
>
> 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
> 	Subsystem: Intel Corporation NM10/ICH7 Family USB UHCI Controller [8086:464c]
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin B routed to IRQ 19
> 	Region 4: I/O ports at 2020 [size=32]
> 	Kernel driver in use: uhci_hcd
> 	Kernel modules: uhci_hcd
>
> 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
> 	Subsystem: Intel Corporation NM10/ICH7 Family USB UHCI Controller [8086:464c]
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin D routed to IRQ 16
> 	Region 4: I/O ports at 2040 [size=32]
> 	Kernel driver in use: uhci_hcd
> 	Kernel modules: uhci_hcd
>
> 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
> 	Subsystem: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:464c]
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin A routed to IRQ 23
> 	Region 0: Memory at e0304000 (32-bit, non-prefetchable) [size=1K]
> 	Capabilities: <access denied>
> 	Kernel driver in use: ehci-pci
> 	Kernel modules: ehci_pci
>
> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode])
> 	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
> 	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> 	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> 	Capabilities: <access denied>
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
> 	Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:464c]
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Capabilities: <access denied>
> 	Kernel driver in use: lpc_ich
> 	Kernel modules: intel_rng, lpc_ich, leds_ss4200
>
> 00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [ISA Compatibility mode controller, supports both channels switched to PCI native mode, supports bus mastering])
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
> 	Latency: 0
> 	Interrupt: pin A routed to IRQ 18
> 	Region 0: I/O ports at 01f0 [size=8]
> 	Region 1: I/O ports at 03f4
> 	Region 2: I/O ports at 0170 [size=8]
> 	Region 3: I/O ports at 0374
> 	Region 4: I/O ports at 2060 [size=16]
> 	Kernel driver in use: ata_piix
> 	Kernel modules: ata_piix, ata_generic
>
> 00:1f.2 IDE interface [0101]: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] [8086:27c0] (rev 01) (prog-if 8f [PCI native mode controller, supports both channels switched to ISA compatibility mode, supports bus mastering])
> 	Subsystem: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] [8086:464c]
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin B routed to IRQ 19
> 	Region 0: I/O ports at 2098 [size=8]
> 	Region 1: I/O ports at 20b0 [size=4]
> 	Region 2: I/O ports at 20a0 [size=8]
> 	Region 3: I/O ports at 20b4 [size=4]
> 	Region 4: I/O ports at 2070 [size=16]
> 	Capabilities: <access denied>
> 	Kernel driver in use: ata_piix
> 	Kernel modules: ata_piix, ata_generic
>
> 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 01)
> 	Subsystem: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:464c]
> 	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Interrupt: pin B routed to IRQ 19
> 	Region 4: I/O ports at 0400 [size=32]
> 	Kernel driver in use: i801_smbus
> 	Kernel modules: i2c_i801
>
> 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 02)
> 	Subsystem: Intel Corporation RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [8086:0001]
> 	Physical Slot: 0
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0, Cache Line Size: 64 bytes
> 	Interrupt: pin A routed to IRQ 28
> 	Region 0: I/O ports at 1000 [size=256]
> 	Region 2: Memory at e0120000 (64-bit, non-prefetchable) [size=4K]
> 	Region 4: Memory at e0000000 (64-bit, prefetchable) [size=64K]
> 	Expansion ROM at e0100000 [disabled] [size=128K]
> 	Capabilities: <access denied>
> 	Kernel driver in use: r8169
> 	Kernel modules: r8169
>
>
> ** USB devices:
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>
>
> -- System Information:
> Debian Release: 10.0
>   APT prefers stable
>   APT policy: (500, 'stable')
> Architecture: amd64 (x86_64)
>
> Kernel: Linux 4.9.0-9-amd64 (SMP w/4 CPU cores)
> Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8), LANGUAGE=en_GB:en (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
> Init: systemd (via /run/systemd/system)
>
> Versions of packages linux-image-4.19.0-5-amd64 depends on:
> ii  initramfs-tools [linux-initramfs-tool]  0.133
> ii  kmod                                    26-1
> ii  linux-base                              4.6
>
> Versions of packages linux-image-4.19.0-5-amd64 recommends:
> pn  apparmor             <none>
> ii  firmware-linux-free  3.4
>
> Versions of packages linux-image-4.19.0-5-amd64 suggests:
> pn  debian-kernel-handbook  <none>
> ii  grub-pc                 2.02+dfsg1-20
> pn  linux-doc-4.19          <none>
>
> Versions of packages linux-image-4.19.0-5-amd64 is related to:
> pn  firmware-amd-graphics     <none>
> pn  firmware-atheros          <none>
> pn  firmware-bnx2             <none>
> pn  firmware-bnx2x            <none>
> pn  firmware-brcm80211        <none>
> pn  firmware-cavium           <none>
> pn  firmware-intel-sound      <none>
> pn  firmware-intelwimax       <none>
> pn  firmware-ipw2x00          <none>
> pn  firmware-ivtv             <none>
> pn  firmware-iwlwifi          <none>
> pn  firmware-libertas         <none>
> pn  firmware-linux-nonfree    <none>
> pn  firmware-misc-nonfree     <none>
> pn  firmware-myricom          <none>
> pn  firmware-netxen           <none>
> pn  firmware-qlogic           <none>
> pn  firmware-realtek          <none>
> pn  firmware-samsung          <none>
> pn  firmware-siano            <none>
> pn  firmware-ti-connectivity  <none>
> pn  xen-hypervisor            <none>
>
> -- no debconf information
>


Reply to: