Bug#927921: Modeset: Invalid argument. No GUI.
Package: src:linux
Version: 4.19.28-2
Severity: important
Dear maintainer,
I have two kernels installed: 4.19.0-2 and 4.19.0-4 (both amd64 from buster). The described problems happen only when 4.19.0-4 is booted.
Basically, any (Xorg) GUI start fails, and /var/log/Xorg.0.log contains eg. this line:
(EE) modeset(0): Failed to set mode: Invalid argument
I have not much ideas what additional information could help, please tell me anything you'd like to know.
Note that I have installed bumblebee and nvidia driver, but run intel driver usually. Completely removing bumblebee and anything nvidia-related doesn't change the situation.
Thank you
-- Package-specific info:
** Version:
Linux version 4.19.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-2)) #1 SMP Debian 4.19.28-2 (2019-03-15)
** Command line:
BOOT_IMAGE=/vmlinuz-4.19.0-4-amd64 root=/dev/mapper/sda4_crypt ro rootflags=subvol=main quiet
** Tainted: OE (12288)
* Out-of-tree module has been loaded.
* Unsigned module has been loaded.
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
sys_vendor: Dell Inc.
product_name: Precision 7520
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: 1.13.0
board_vendor: Dell Inc.
board_name: 09Y5WW
board_version: A00
** Loaded modules:
pci_stub
vboxpci(OE)
vboxnetadp(OE)
vboxnetflt(OE)
vboxdrv(OE)
fuse
i2c_dev
cmac
bnep
bbswitch(OE)
snd_hda_codec_hdmi
snd_hda_codec_realtek
snd_hda_codec_generic
nls_ascii
nls_cp437
vfat
fat
ext4
mbcache
jbd2
fscrypto
ecb
ip6t_REJECT
nf_reject_ipv6
cdc_mbim
arc4
cdc_wdm
cdc_ncm
usbnet
qcserial
usb_wwan
mii
usbserial
xt_hl
ip6_tables
ip6t_rt
ipt_REJECT
nf_reject_ipv4
dell_rbtn
mei_wdt
dell_wmi
wmi_bmof
mxm_wmi
intel_rapl
x86_pkg_temp_thermal
intel_powerclamp
ppdev
coretemp
nft_limit
dell_laptop
dell_smbios
kvm_intel
dell_wmi_descriptor
iwlmvm
btusb
btrtl
dcdbas
btbcm
kvm
btintel
dell_smm_hwmon
irqbypass
mac80211
sg
bluetooth
intel_cstate
xt_limit
drbg
joydev
evdev
ansi_cprng
serio_raw
xt_addrtype
xt_tcpudp
ecdh_generic
efi_pstore
snd_hda_intel
iwlwifi
intel_uncore
crc16
intel_rapl_perf
snd_hda_codec
i915
xt_conntrack
snd_hda_core
nft_compat
rtsx_pci_ms
efivars
snd_hwdep
cfg80211
snd_pcm
iTCO_wdt
memstick
iTCO_vendor_support
snd_timer
snd
soundcore
rfkill
drm_kms_helper
idma64
nft_counter
drm
mei_me
mei
processor_thermal_device
parport_pc
ie31200_edac
i2c_algo_bit
intel_soc_dts_iosf
parport
intel_pch_thermal
battery
int3403_thermal
dell_smo8800
wmi
intel_hid
int3400_thermal
int3402_thermal
video
sparse_keymap
acpi_thermal_rel
int340x_thermal_zone
pcc_cpufreq
acpi_pad
ac
button
nf_conntrack_netbios_ns
nf_conntrack_broadcast
nf_nat_ftp
nf_nat
nf_conntrack_ftp
nf_conntrack
nf_defrag_ipv6
nf_defrag_ipv4
nf_tables
nfnetlink
efivarfs
ip_tables
x_tables
autofs4
btrfs
xor
zstd_decompress
zstd_compress
xxhash
raid6_pq
libcrc32c
crc32c_generic
algif_skcipher
af_alg
sr_mod
cdrom
uas
usb_storage
usbhid
dm_crypt
dm_mod
sd_mod
hid_alps
hid_generic
crct10dif_pclmul
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
pcbc
rtsx_pci_sdmmc
mmc_core
ahci
xhci_pci
libahci
xhci_hcd
aesni_intel
aes_x86_64
libata
crypto_simd
psmouse
cryptd
e1000e
glue_helper
usbcore
scsi_mod
i2c_hid
i2c_i801
rtsx_pci
hid
intel_lpss_pci
intel_lpss
usb_common
thermal
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers [8086:5918] (rev 05)
Subsystem: Dell Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: ie31200_edac
Kernel modules: ie31200_edac
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x16) [8086:1901] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ec000000-ed0fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics P630 [8086:591d] (rev 04) (prog-if 00 [VGA controller])
Subsystem: Dell HD Graphics P630 [1028:07b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 131
Region 0: Memory at eb000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:04.0 Signal processing controller [1180]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem [8086:1903] (rev 05)
Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem [1028:07b0]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed340000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: proc_thermal
Kernel modules: processor_thermal_device
00:14.0 USB controller [0c03]: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [8086:a12f] (rev 31) (prog-if 30 [XHCI])
Subsystem: Dell 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 129
Region 0: Memory at ed330000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:14.2 Signal processing controller [1180]: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem [8086:a131] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Thermal Subsystem [1028:07b0]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ed358000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal
00:15.0 Signal processing controller [1180]: Intel Corporation 100 Series/C230 Series Chipset Family Serial IO I2C Controller #0 [8086:a160] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Serial IO I2C Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed357000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.1 Signal processing controller [1180]: Intel Corporation 100 Series/C230 Series Chipset Family Serial IO I2C Controller #1 [8086:a161] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Serial IO I2C Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at ed356000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:16.0 Communication controller [0780]: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 [8086:a13a] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family MEI Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 130
Region 0: Memory at ed355000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:17.0 SATA controller [0106]: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [8086:a102] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [1028:07b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 128
Region 0: Memory at ed350000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at ed354000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at ed353000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1c.0 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #2 [8086:a111] (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: ed200000-ed2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #3 [8086:a112] (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: ed100000-ed1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #5 [8086:a114] (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
Bus: primary=00, secondary=04, subordinate=3c, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d4000000-ea0fffff
Prefetchable memory behind bridge: 0000000090000000-00000000b1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge [0601]: Intel Corporation CM238 Chipset LPC/eSPI Controller [8086:a154] (rev 31)
Subsystem: Dell CM238 Chipset LPC/eSPI Controller [1028:07b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.2 Memory controller [0580]: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller [8086:a121] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Power Management Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at ed34c000 (32-bit, non-prefetchable) [size=16K]
00:1f.3 Audio device [0403]: Intel Corporation CM238 HD Audio Controller [8086:a171] (rev 31)
Subsystem: Dell CM238 HD Audio Controller [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 133
Region 0: Memory at ed348000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at ed320000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.4 SMBus [0c05]: Intel Corporation 100 Series/C230 Series Chipset Family SMBus [8086:a123] (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family SMBus [1028:07b0]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed352000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (5) I219-LM [8086:15e3] (rev 31)
Subsystem: Dell Ethernet Connection (5) I219-LM [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 127
Region 0: Memory at ed300000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GM107GLM [Quadro M1200 Mobile] [10de:13b6] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel modules: nvidia
02:00.0 Network controller [0280]: Intel Corporation Wireless 8265 / 8275 [8086:24fd] (rev 78)
Subsystem: Intel Corporation Wireless 8265 / 8275 [8086:0050]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 132
Region 0: Memory at ed200000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS525A PCI Express Card Reader [10ec:525a] (rev 01)
Subsystem: Dell RTS525A PCI Express Card Reader [1028:07b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 126
Region 1: Memory at ed100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci
** USB devices:
Bus 002 Device 003: ID 413c:5534 Dell Computer Corp.
Bus 002 Device 002: ID 413c:81b6 Dell Computer Corp.
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 413c:2134 Dell Computer Corp.
Bus 001 Device 003: ID 8087:0a2b Intel Corp.
Bus 001 Device 006: ID 046d:c328 Logitech, Inc. Corded Keyboard K280e
Bus 001 Device 004: ID 1bcf:0005 Sunplus Innovation Technology Inc. Optical Mouse
Bus 001 Device 008: ID 13fd:3940 Initio Corporation external DVD burner ECD819-SU3
Bus 001 Device 002: ID 413c:2513 Dell Computer Corp. internal USB Hub of E-Port Replicator
Bus 001 Device 007: ID 0a5c:5832 Broadcom Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: buster/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.19.0-4-amd64 (SMP w/8 CPU cores)
Kernel taint flags: TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8), LANGUAGE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-4.19.0-4-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.133
ii kmod 26-1
ii linux-base 4.5
Versions of packages linux-image-4.19.0-4-amd64 recommends:
ii apparmor 2.13.2-10
ii firmware-linux-free 3.4
ii irqbalance 1.5.0-3
Versions of packages linux-image-4.19.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-efi-amd64 2.02+dfsg1-11
pn linux-doc-4.19 <none>
Versions of packages linux-image-4.19.0-4-amd64 is related to:
ii firmware-amd-graphics 20190114-1
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20190114-1
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
ii firmware-misc-nonfree 20190114-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: