--- Begin Message ---
Package: src:linux
Version: 4.18.20-2
Severity: normal
Dear Maintainer,
I tried Buster with 4.18.20-2 kernel on an Alix 2C2, with Geode LX800, BIOS 0.99m.
After grub unpacking initramfs, the (serial) console outputs nothing (despite earlyprintk/boot_delay), then it reboots by itself.
(Same with 4.18.10-1)
Then I tried linux-image-4.18.0-0.bpo.1-686_4.18.6-1~bpo9+1_i386.deb, and that works mostly fine.
With this kernel, printk starts at about the same time, as with the other kernel I would see the POST.
(Stretch 4.9 kernel also works FWIW).
For reference, I saw a Geode LX issue mentioned in this thread too:
https://lists.debian.org/debian-kernel/2018/09/msg00295.html
My issue is maybe different than that, because I get no output at all (no "not compatible with i586" message).
And as the stretch-backports kernel does work, I thought it isn't due to (the mentioned in thread) upstream, but due to Debian's config.
(Or was perhaps meant, upstream gcc?)
>From the Debian kernel changelog I concluded, the problem from that thread might have been fixed in 4.18.10-1. At least in there is a Geode fix.
So, as mentioned, I also tried that kernel, but same problem.
Note that the info below is while booted with the backports kernel (same commandline options etc).
The info above (Subject/Version) I edited to match the nonbooting kernel.
Thank you,
Gert
-- Package-specific info:
** Version:
Linux version 4.18.0-0.bpo.1-686
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.18.0-0.bpo.1-686 root=UUID=423c6d29-ad6f-4de5-8612-b7dfcf8c9efd ro console=ttyS0,115200n8 earlyprintk=ttyS0,115200n8 apparmor=1 security=apparmor ipv6.disable=1 noisapnp slub_debug=P page_poison=1 slab_nomerge pti=on nomfgpt
** Not tainted
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
Alix 2C2
Geode LX800
BIOS 0.99m
** Loaded modules:
evdev
gpio_cs5535
scx200_acb
cs5535_mfgpt
ohci_pci
ohci_hcd
ehci_pci
cbc
ehci_hcd
pcspkr
sg
geode_aes
usbcore
gpio_keys_polled
via_rhine
mii
leds_gpio
input_polldev
cs5535_mfd
usb_common
geode_rng
rng_core
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
fscrypto
ecb
crypto_simd
cryptd
aes_i586
sd_mod
ata_generic
pata_cs5536
pata_amd
libata
scsi_mod
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug enp0s9
iface enp0s9 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: enp0s9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0d:b9:12:d0:f4 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.226/24 brd 192.168.1.255 scope global enp0s9
valid_lft forever preferred_lft forever
3: enp0s11: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:0d:b9:12:d0:f5 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
enp0s11: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
enp0s9: 59613 392 0 0 0 0 0 0 59482 343 0 0 0 0 0 0
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
** PCI devices:
00:01.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge [1022:2080] (rev 31)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge [1022:2080]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248, Cache Line Size: 32 bytes
Region 0: I/O ports at 0000
00:01.2 Entertainment encryption device [1010]: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block [1022:2082]
Subsystem: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block [1022:2082]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at efff4000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: Geode LX AES
Kernel modules: geode_rng, geode_aes
00:09.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Subsystem: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:0106]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
Kernel modules: via_rhine
00:0b.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Subsystem: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:0106]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at e0040000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
Kernel modules: via_rhine
00:0f.0 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA [1022:2090] (rev 03)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA [1022:2090]
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 6000 [size=8]
Region 1: I/O ports at 6100 [size=256]
Region 2: I/O ports at 6200 [size=64]
Region 3: I/O ports at 0000
Region 4: I/O ports at 9d00 [size=128]
Region 5: I/O ports at 9c00 [size=64]
Kernel driver in use: cs5535-mfd
Kernel modules: cs5535_mfd
00:0f.2 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE [1022:209a] (rev 01) (prog-if 80 [ISA Compatibility mode-only controller, supports bus mastering])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE [1022:209a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248, Cache Line Size: 32 bytes
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at ff00 [size=16]
Kernel driver in use: pata_amd
Kernel modules: pata_amd, pata_cs5536, ata_generic
00:0f.4 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC [1022:2094] (rev 02) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC [1022:2094]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 12
Region 0: Memory at efffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:0f.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC [1022:2095] (rev 02) (prog-if 20 [EHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC [1022:2095]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 12
Region 0: Memory at efffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
** USB devices:
not available
-- System Information:
Debian Release: buster/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i586)
Kernel: Linux 4.18.0-0.bpo.1-686 (SMP w/1 CPU core)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968), LANGUAGE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-4.18.0-0.bpo.1-686 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.132
ii kmod 25-2
ii linux-base 4.5
Versions of packages linux-image-4.18.0-0.bpo.1-686 recommends:
ii apparmor 2.13.1-3+b1
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-4.18.0-0.bpo.1-686 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02+dfsg1-8
pn linux-doc-4.18 <none>
Versions of packages linux-image-4.18.0-0.bpo.1-686 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
*** /tmp/dmesg-4.18.0-0.bpo.1-686
[ 0.000000] Linux version 4.18.0-0.bpo.1-686 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Debian 4.18.6-1~bpo9+1 (2018-09-13)
[ 0.000000] x86/fpu: x87 FPU will use FSAVE
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[ 0.000000] bootconsole [earlyser0] enabled
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI not present or invalid.
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] last_pfn = 0x10000 max_arch_pfn = 0x100000
[ 0.000000] Disabled
[ 0.000000] x86/PAT: MTRRs disabled, skipping PAT initialization too.
[ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC
[ 0.000000] initial memory mapped: [mem 0x00000000-0x09ffffff]
[ 0.000000] Base memory trampoline at [(ptrval)] 9b000 size 16384
[ 0.000000] RAMDISK: [mem 0x0f571000-0x0fa0afff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI BIOS Error (bug): A valid RSDP was not found (20180531/tbxfroot-210)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 256MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 10000000
[ 0.000000] low ram: 0 - 10000000
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] BRK [0x09a59000, 0x09a59fff] PGTABLE
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65439
[ 0.000000] DMA zone: 40 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3999 pages, LIFO batch:0
[ 0.000000] Normal zone: 600 pages used for memmap
[ 0.000000] Normal zone: 61440 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] SFI: Simple Firmware Interface v0.81 http://simplefirmware.org
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] [mem 0x10000000-0xffefffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] random: get_random_bytes called from start_kernel+0x81/0x47e with crng_init=0
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] percpu: Embedded 29 pages/cpu @(ptrval) s86924 r0 d31860 u118784
[ 0.000000] pcpu-alloc: s86924 r0 d31860 u118784 alloc=29*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64799
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-0.bpo.1-686 root=UUID=423c6d29-ad6f-4de5-8612-b7dfcf8c9efd ro console=ttyS0,115200n8 earlyprintk=ttyS0,115200n8 apparmor=1 security=apparmor ipv6.disable=1 noisapnp slub_debug=P page_poison=1 slab_nomerge pti=on nomfgpt
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] BRK [0x09a5a000, 0x09a5afff] PGTABLE
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 243468K/261756K available (6429K kernel code, 634K rwdata, 2032K rodata, 828K init, 424K bss, 18288K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] virtual kernel memory layout:
fixmap : 0xffd35000 - 0xfffff000 (2856 kB)
cpu_entry : 0xff400000 - 0xff8e1000 (4996 kB)
pkmap : 0xff000000 - 0xff400000 (4096 kB)
vmalloc : 0xd0800000 - 0xfeffe000 ( 743 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
.init : 0xc98f3000 - 0xc99c2000 ( 828 kB)
.data : 0xc96474e4 - 0xc98e3900 (2673 kB)
.text : 0xc9000000 - 0xc96474e4 (6429 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] ftrace: allocating 28661 entries in 56 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 2304, nr_irqs: 32, preallocated irqs: 16
[ 0.000000] CPU 0 irqstacks, hard=(ptrval) soft=(ptrval)
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [ttyS0] enabled
[ 0.000000] bootconsole [earlyser0] disabled
[ 0.004000] APIC: Keep in PIC mode(8259)
[ 0.008000] tsc: Fast TSC calibration using PIT
[ 0.012000] tsc: Detected 498.057 MHz processor
[ 0.016000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0xe5bc0194ba, max_idle_ns: 881590443460 ns
[ 0.020023] Calibrating delay loop (skipped), value calculated using timer frequency.. 996.11 BogoMIPS (lpj=1992228)
[ 0.024018] pid_max: default: 32768 minimum: 301
[ 0.028672] Security Framework initialized
[ 0.032041] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.036626] AppArmor: AppArmor initialized
[ 0.040222] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044025] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.054233] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.056025] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.060032] Spectre V2 : Spectre mitigation: LFENCE not serializing, switching to generic retpoline
[ 0.064015] Spectre V2 : Mitigation: Full generic retpoline
[ 0.068014] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.072015] Speculative Store Bypass: Vulnerable
[ 0.100164] Freeing SMP alternatives memory: 20K
[ 0.111497] smpboot: weird, boot CPU (#0) not listed by the BIOS
[ 0.112021] smpboot: SMP disabled
[ 0.117232] Performance Events: no PMU driver, software events only.
[ 0.120524] Hierarchical SRCU implementation.
[ 0.129870] NMI watchdog: Perf event create on CPU 0 failed with -2
[ 0.132018] NMI watchdog: Perf NMI watchdog permanently disabled
[ 0.136605] smp: Bringing up secondary CPUs ...
[ 0.140028] smp: Brought up 1 node, 1 CPU
[ 0.144019] smpboot: Max logical packages: 1
[ 0.148023] smpboot: Total of 1 processors activated (996.11 BogoMIPS)
[ 0.156213] devtmpfs: initialized
[ 0.163962] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.164040] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.172519] pinctrl core: initialized pinctrl subsystem
[ 0.180835] NET: Registered protocol family 16
[ 0.188096] audit: initializing netlink subsys (disabled)
[ 0.196046] audit: type=2000 audit(946684836.192:1): state=initialized audit_enabled=0 res=1
[ 0.200354] cpuidle: using governor ladder
[ 0.204040] cpuidle: using governor menu
[ 0.208698] clocksource: pit: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1601818034827 ns
[ 0.219921] PCI: PCI BIOS revision 2.10 entry at 0xfcf35, last bus=0
[ 0.220018] PCI: Using configuration type 1 for base access
[ 0.250234] HugeTLB registered 4.00 MiB page size, pre-allocated 0 pages
[ 0.256484] ACPI: Interpreter disabled.
[ 0.260758] vgaarb: loaded
[ 0.264696] EDAC MC: Ver: 3.0.0
[ 0.269256] PCI: Probing PCI hardware
[ 0.272053] PCI: root bus 00: using default resources
[ 0.272072] PCI: Probing PCI hardware (bus 00)
[ 0.272537] PCI host bridge to bus 0000:00
[ 0.276082] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.280054] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.284027] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.288098] pci 0000:00:01.0: [1022:2080] type 00 class 0x060000
[ 0.288157] pci 0000:00:01.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 0.292688] pci 0000:00:01.2: [1022:2082] type 00 class 0x101000
[ 0.292759] pci 0000:00:01.2: reg 0x10: [mem 0xefff4000-0xefff7fff]
[ 0.293492] pci 0000:00:09.0: [1106:3053] type 00 class 0x020000
[ 0.293537] pci 0000:00:09.0: reg 0x10: [io 0x1000-0x10ff]
[ 0.293565] pci 0000:00:09.0: reg 0x14: [mem 0xe0000000-0xe00000ff]
[ 0.296052] pci 0000:00:09.0: supports D1 D2
[ 0.296069] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.296701] pci 0000:00:0b.0: [1106:3053] type 00 class 0x020000
[ 0.296747] pci 0000:00:0b.0: reg 0x10: [io 0x1400-0x14ff]
[ 0.296774] pci 0000:00:0b.0: reg 0x14: [mem 0xe0040000-0xe00400ff]
[ 0.296880] pci 0000:00:0b.0: supports D1 D2
[ 0.296896] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.297507] pci 0000:00:0f.0: [1022:2090] type 00 class 0x060100
[ 0.297667] pci 0000:00:0f.0: reg 0x10: [io 0x6000-0x6007]
[ 0.297768] pci 0000:00:0f.0: reg 0x14: [io 0x6100-0x61ff]
[ 0.297869] pci 0000:00:0f.0: reg 0x18: [io 0x6200-0x623f]
[ 0.298023] pci 0000:00:0f.0: reg 0x20: [io 0x9d00-0x9d7f]
[ 0.298124] pci 0000:00:0f.0: reg 0x24: [io 0x9c00-0x9c3f]
[ 0.298703] pci 0000:00:0f.2: [1022:209a] type 00 class 0x010180
[ 0.298961] pci 0000:00:0f.2: reg 0x20: [io 0xff00-0xff0f]
[ 0.299066] pci 0000:00:0f.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.300031] pci 0000:00:0f.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.304028] pci 0000:00:0f.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.312023] pci 0000:00:0f.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.316616] pci 0000:00:0f.4: [1022:2094] type 00 class 0x0c0310
[ 0.316723] pci 0000:00:0f.4: reg 0x10: [mem 0xefffe000-0xefffefff]
[ 0.317027] pci 0000:00:0f.4: PME# supported from D0 D3hot D3cold
[ 0.320265] pci 0000:00:0f.5: [1022:2095] type 00 class 0x0c0320
[ 0.320375] pci 0000:00:0f.5: reg 0x10: [mem 0xefffd000-0xefffdfff]
[ 0.320690] pci 0000:00:0f.5: PME# supported from D0 D3hot D3cold
[ 0.321327] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.321624] PCI: pci_cache_line_size set to 32 bytes
[ 0.324625] clocksource: Switched to clocksource tsc-early
[ 0.534503] VFS: Disk quotas dquot_6.6.0
[ 0.538651] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.547529] AppArmor: AppArmor Filesystem Enabled
[ 0.552440] pnp: PnP ACPI: disabled
[ 0.555967] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.561877] PnPBIOS: PnP BIOS support was not detected.
[ 0.598366] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.598387] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 0.598858] NET: Registered protocol family 2
[ 0.605771] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.613688] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.620777] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.627322] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.633944] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.639846] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.646753] NET: Registered protocol family 1
[ 0.651545] PCI: CLS 32 bytes, default 32
[ 0.652330] Unpacking initramfs...
[ 1.043439] random: fast init done
[ 1.694552] Freeing initrd memory: 4712K
[ 1.699579] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 1.710439] alix: system is recognized as "PC Engines ALIX.2 v0.99m"
[ 1.724505] Initialise system trusted keyrings
[ 1.729411] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 1.775661] zbud: loaded
[ 1.782933] pstore: using deflate compression
[ 2.716238] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe5bc0194ba, max_idle_ns: 881590443460 ns
[ 2.735717] clocksource: Switched to clocksource tsc
[ 22.052697] Key type asymmetric registered
[ 22.056949] Asymmetric key parser 'x509' registered
[ 22.062570] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 22.070324] io scheduler noop registered
[ 22.074347] io scheduler deadline registered
[ 22.079558] io scheduler cfq registered (default)
[ 22.084334] io scheduler mq-deadline registered
[ 22.092745] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 22.099749] unchecked MSR access error: RDMSR from 0x179 at rIP: 0xc90450d7 (native_read_msr+0x7/0x40)
[ 22.109094] Call Trace:
[ 22.111574] ? ghes_init+0x12f/0x12f
[ 22.115207] extlog_init+0x21/0x318
[ 22.118752] ? driver_register+0x83/0xf0
[ 22.122730] do_one_initcall+0x42/0x1ae
[ 22.126620] ? do_early_param+0x7a/0x7a
[ 22.130514] kernel_init_freeable+0x159/0x1de
[ 22.134926] ? rest_init+0xa0/0xa0
[ 22.138382] kernel_init+0xd/0x100
[ 22.141847] ret_from_fork+0x2e/0x38
[ 22.145687] isapnp: ISA Plug & Play support disabled
[ 22.151740] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 22.158688] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 921600) is a NS16550A
[ 22.167892] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 921600) is a NS16550A
[ 22.180786] Linux agpgart interface v0.103
[ 22.188207] i8042: PNP: No PS/2 controller found.
[ 22.192991] i8042: Probing ports directly.
[ 23.229335] i8042: No controller found
[ 23.234030] mousedev: PS/2 mouse device common for all mice
[ 23.240817] rtc_cmos rtc_cmos: registered as rtc0
[ 23.245885] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram
[ 23.252606] ledtrig-cpu: registered to indicate activity on CPUs
[ 23.260443] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 23.268058] mip6: Mobile IPv6
[ 23.271037] mip6: mip6_init: can't add xfrm type(destopt)
[ 23.276482] NET: Registered protocol family 17
[ 23.281040] mpls_gso: MPLS GSO support
[ 23.284847] mce: Unable to init MCE device (rc: -5)
[ 23.290380] Using IPI No-Shortcut mode
[ 23.294213] sched_clock: Marking stable (23294146933, 0)->(23375162589, -81015656)
[ 23.303679] registered taskstats version 1
[ 23.307845] Loading compiled-in X.509 certificates
[ 25.725011] Loaded X.509 cert 'secure-boot-test-key-lfaraone: 97c1b25cddf9873ca78a58f3d73bf727d2cf78ff'
[ 25.735121] zswap: loaded using pool lzo/zbud
[ 25.739966] AppArmor: AppArmor sha1 policy hashing enabled
[ 25.750216] rtc_cmos rtc_cmos: setting system clock to 2000-01-01 00:01:01 UTC (946684861)
[ 25.798664] Freeing unused kernel image memory: 828K
[ 25.808625] Write protecting the kernel text: 6432k
[ 25.814017] Write protecting the kernel read-only data: 2036k
[ 26.791524] SCSI subsystem initialized
[ 26.898999] libata version 3.00 loaded.
[ 26.903159] pata_amd 0000:00:0f.2: version 0.4.1
[ 26.948234] scsi host0: pata_amd
[ 26.979421] scsi host1: pata_amd
[ 26.989329] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 26.996375] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 27.160815] ata1.00: CFA: SanDisk SDCFX3-2048, HDX 4.21, max MWDMA2
[ 27.167175] ata1.00: 4001760 sectors, multi 0: LBA
[ 27.211101] scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFX3-2 4.21 PQ: 0 ANSI: 5
[ 27.244582] ata2: port disabled--ignoring
[ 27.321949] sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.05 GB/1.91 GiB)
[ 27.332911] sd 0:0:0:0: [sda] Write Protect is off
[ 27.337822] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 27.337972] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 27.352646] sda: sda1
[ 27.359512] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 27.796286] cryptd: max_cpu_qlen set to 1000
[ 28.237122] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 29.339285] systemd[1]: System time before build time, advancing clock.
[ 29.597094] systemd[1]: systemd 239 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 29.618809] systemd[1]: No virtualization found in DMI
[ 29.618846] systemd[1]: No virtualization found in CPUID
[ 29.618940] systemd[1]: Virtualization XEN not found, /proc/xen does not exist
[ 29.619041] systemd[1]: This platform does not support /proc/device-tree
[ 29.619418] systemd[1]: UML virtualization not found in /proc/cpuinfo.
[ 29.619458] systemd[1]: This platform does not support /proc/sysinfo
[ 29.619497] systemd[1]: Found VM virtualization none
[ 29.619576] systemd[1]: Detected architecture x86.
[ 29.625710] systemd[1]: Mounting cgroup to /sys/fs/cgroup/devices of type cgroup with options devices.
[ 31.065637] random: systemd: uninitialized urandom read (16 bytes read)
[ 31.089383] random: systemd: uninitialized urandom read (16 bytes read)
[ 31.116354] random: systemd: uninitialized urandom read (16 bytes read)
[ 31.473767] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 31.811410] systemd[170]: Operating on architecture: x86
[ 31.811546] systemd[170]: Operating on architecture: x86
[ 31.818122] systemd[170]: Operating on architecture: x86
[ 31.818808] systemd[170]: Restricting namespace to: .
[ 31.818948] systemd[170]: Operating on architecture: x86
[ 31.819095] systemd[170]: Blocking cgroup.
[ 31.819238] systemd[170]: Blocking ipc.
[ 31.819382] systemd[170]: Blocking net.
[ 31.819529] systemd[170]: Blocking mnt.
[ 31.819714] systemd[170]: Blocking pid.
[ 31.819961] systemd[170]: Blocking user.
[ 31.824391] systemd[170]: Blocking uts.
[ 31.825705] systemd[170]: Operating on architecture: x86
[ 31.826983] systemd[170]: Failed to add rule for system call set_tls() / -10183, ignoring: Numerical argument out of domain
[ 31.827824] systemd[170]: Failed to add rule for system call epoll_wait_old() / -10006, ignoring: Numerical argument out of domain
[ 31.838810] systemd[170]: Failed to add rule for system call newfstatat() / -10031, ignoring: Numerical argument out of domain
[ 31.839946] systemd[170]: Failed to add rule for system call epoll_ctl_old() / -10005, ignoring: Numerical argument out of domain
[ 32.973366] systemd[176]: Operating on architecture: x86
[ 32.973516] systemd[176]: Operating on architecture: x86
[ 32.981229] systemd[176]: Operating on architecture: x86
[ 33.746699] systemd-journald[170]: Received request to flush runtime journal from PID 1
[ 34.455116] AMD Geode RNG detected
[ 34.503323] cs5535-mfd 0000:00:0f.0: 5 devices registered.
[ 34.546183] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 34.562235] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 34.672582] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 34.708442] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 34.756995] via-rhine 0000:00:09.0 eth0: VIA Rhine III (Management Adapter) at (ptrval), 00:0d:b9:12:d0:f4, IRQ 10
[ 34.768247] via-rhine 0000:00:09.0 eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link cde1
[ 34.782628] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 34.791908] usbcore: registered new interface driver usbfs
[ 34.864504] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 34.885241] usbcore: registered new interface driver hub
[ 34.968585] usbcore: registered new device driver usb
[ 35.064658] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 35.089725] Error allocating fallback algo cbc(aes)
[ 35.094741] alg: skcipher: Failed to load transform for cbc-aes-geode: -2
[ 35.119031] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 35.170020] via-rhine 0000:00:0b.0 eth1: VIA Rhine III (Management Adapter) at (ptrval), 00:0d:b9:12:d0:f5, IRQ 15
[ 35.181245] via-rhine 0000:00:0b.0 eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 35.249217] ehci-pci: EHCI PCI platform driver
[ 35.259368] Geode LX AES 0000:00:01.2: GEODE AES engine enabled.
[ 35.296637] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 35.308610] ehci-pci 0000:00:0f.5: EHCI Host Controller
[ 35.320661] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 35.393184] ehci-pci 0000:00:0f.5: new USB bus registered, assigned bus number 1
[ 35.488485] ehci-pci 0000:00:0f.5: irq 12, io mem 0xefffd000
[ 35.494789] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 35.608262] ehci-pci 0000:00:0f.5: USB 2.0 started, EHCI 1.00
[ 35.673869] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 35.682362] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 35.689647] usb usb1: Product: EHCI Host Controller
[ 35.694578] usb usb1: Manufacturer: Linux 4.18.0-0.bpo.1-686 ehci_hcd
[ 35.701069] usb usb1: SerialNumber: 0000:00:0f.5
[ 36.082504] hub 1-0:1.0: USB hub found
[ 36.128459] hub 1-0:1.0: 4 ports detected
[ 36.144222] audit: type=1400 audit(1544179683.772:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=210 comm="apparmor_parser"
[ 36.195033] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 36.236314] ohci-pci: OHCI PCI platform driver
[ 36.256599] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 36.279035] ohci-pci 0000:00:0f.4: OHCI PCI host controller
[ 36.308506] audit: type=1400 audit(1544179683.772:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=210 comm="apparmor_parser"
[ 36.333127] cs5535-mfgpt cs5535-mfgpt: reserved resource region [io 0x6200-0x623f]
[ 36.341001] cs5535-mfgpt cs5535-mfgpt: 8 MFGPT timers available
[ 36.362988] cs5535-gpio cs5535-gpio: reserved resource region [io 0x6100-0x61ff]
[ 36.377915] cs5535-smb cs5535-smb: SCx200 device 'CS5535 ACB0' registered
[ 36.395736] ohci-pci 0000:00:0f.4: new USB bus registered, assigned bus number 2
[ 36.460739] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517
[ 36.481585] ohci-pci 0000:00:0f.4: irq 12, io mem 0xefffe000
[ 36.523387] audit: type=1400 audit(1544179683.776:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=210 comm="apparmor_parser"
[ 36.546669] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.1/input/input10
[ 36.644731] via-rhine 0000:00:09.0 enp0s9: renamed from eth0
[ 36.711021] audit: type=1400 audit(1544179684.120:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/chronyd" pid=211 comm="apparmor_parser"
[ 36.750652] via-rhine 0000:00:0b.0 enp0s11: renamed from eth1
[ 36.891240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.18
[ 36.899652] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 36.906930] usb usb2: Product: OHCI PCI host controller
[ 36.912210] usb usb2: Manufacturer: Linux 4.18.0-0.bpo.1-686 ohci_hcd
[ 36.918699] usb usb2: SerialNumber: 0000:00:0f.4
[ 37.142985] hub 2-0:1.0: USB hub found
[ 37.164235] hub 2-0:1.0: 4 ports detected
[ 39.068982] random: crng init done
[ 39.072611] random: 7 urandom warning(s) missed due to ratelimiting
--- End Message ---