Bug#911121: Please compile with CONFIG_SND_BCM2835=m
Package: src:linux
Version: 4.18.10-2
Severity: wishlist
Hi!
I'm currently running this kernel on Raspberry Pi 3b without much trouble,
however no sound devices are found, After reading and looking at raspbian
modules, it seems that sound is handled by this module, so if you would
please enable it with a little luck we'll have sound working on Pi 3b on
standard buster.
Thanks in advance.
-- Package-specific info:
** Version:
Linux version 4.18.0-2-arm64 (debian-kernel@lists.debian.org) (gcc version 7.3.0 (Debian 7.3.0-29)) #1 SMP Debian 4.18.10-2 (2018-10-07)
** Command line:
bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 dma.dmachans=0x7f35 bcm2709.boardrev=0xa02082 bcm2709.serial=0xff0fa6ff bcm2709.uart_clock=48000000 smsc95xx.macaddr=B8:27:EB:0F:A6:FF vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=tty0 console=ttyS1,115200 root=/dev/md1 rw elevator=deadline fsck.repair=yes net.ifnames=0 cma=64M rootwait
** Not tainted
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
Device Tree model: Raspberry Pi 3 Model B Rev 1.2
** Loaded modules:
nf_log_ipv4
nf_log_common
xt_LOG
xt_pkttype
xt_limit
ipt_REJECT
nf_reject_ipv4
xt_owner
xt_conntrack
iptable_filter
ipt_MASQUERADE
xt_REDIRECT
xt_nat
xt_tcpudp
xt_addrtype
iptable_nat
nf_nat_ipv4
nf_nat
nf_conntrack_ipv4
nf_defrag_ipv4
xt_connmark
nf_conntrack
xt_mark
iptable_mangle
bridge
stp
llc
vc4
snd_soc_core
nls_ascii
nls_cp437
snd_pcm_dmaengine
vfat
fat
snd_pcm
brcmfmac
snd_timer
snd
soundcore
cec
brcmutil
drm_kms_helper
cfg80211
drm
asix
sg
bcm2835_rng
rng_core
smsc95xx
libphy
bcm2835_thermal
leds_gpio
usbnet
mii
rfkill
pwm_bcm2835
bcm2835_wdt
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
fscrypto
ecb
aes_arm64
sd_mod
raid10
uas
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
usb_storage
xor
scsi_mod
raid6_pq
libcrc32c
crc32c_generic
raid1
raid0
multipath
linear
md_mod
dwc2
udc_core
usbcore
sdhci_iproc
sdhci_pltfm
usb_common
sdhci
bcm2835
phy_generic
** PCI devices:
not available
** USB devices:
Bus 001 Device 006: ID 0bc2:2322 Seagate RSS LLC
Bus 001 Device 005: ID 0b95:772b ASIX Electronics Corp. AX88772B
Bus 001 Device 004: ID 0939:0b15 Lumberg, Inc. Toshiba Stor.E Alu 2
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: buster/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable')
Architecture: arm64 (aarch64)
Kernel: Linux 4.18.0-2-arm64 (SMP w/4 CPU cores)
Locale: LANG=gl_ES.UTF-8, LC_CTYPE=gl_ES.UTF-8 (charmap=UTF-8), LANGUAGE=gl_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-4.18.0-2-arm64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.132
ii kmod 25-1
ii linux-base 4.5
Versions of packages linux-image-4.18.0-2-arm64 recommends:
ii apparmor 2.13-8
ii firmware-linux-free 3.4
ii irqbalance 1.3.0-0.1+b1
Versions of packages linux-image-4.18.0-2-arm64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-4.18 <none>
Versions of packages linux-image-4.18.0-2-arm64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
ii firmware-brcm80211 20180825+dfsg-1
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-realtek 20180825+dfsg-1
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: