[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#723042: marked as done ([armel/kirkwood] Linux 3.10 fails to boot on QNAP)

Your message dated Sun, 04 Mar 2018 21:26:24 +0100
with message-id <1675396.BpHO95W9OA@kjartansson>
and subject line Re: Bug#723042: QNAP still not booting
has caused the Debian Bug report #723042,
regarding [armel/kirkwood] Linux 3.10 fails to boot on QNAP
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
723042: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=723042
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: src:linux
Version: 3.9.6-1~bpo70+1
Severity: normal

Hi!

  I've upgraded the kernel on my QNAP to 3.9. Unfortunately, network
is now stuck around 1 MBit/s and I'm seeing lots of error messages in
syslog like the ones below:

[  203.642744] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  203.642783] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors

Regards

    Christoph

-- Package-specific info:
** Version:
Linux version 3.9-0.bpo.1-kirkwood (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 Debian 3.9.6-1~bpo70+1

** Command line:
root=/dev/ram initrd=0xa00000,0x900000 ramdisk=34816

** Not tainted

** Kernel log:
[   72.697308] 
[   72.697383] 
[   72.697456] 
[   72.697530] 
[   72.697602] 
[   72.697674] 
[   72.697745] 
[   72.697829] 
[   72.697904] 
[   72.697977] 
[   72.698050] 
[   72.698121] 
[   72.698194] 
[   72.698265] 
[   72.698336] 
[   72.698408] 
[   72.698479] 
[   72.698553] 
[   72.698657] 
[   72.700871] 
[   72.703237] 
[   72.703449] 
[   74.094157] udevd[447]: starting version 175
[   74.651014] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   74.835844] usbcore: registered new interface driver usbfs
[   74.835949] usbcore: registered new interface driver hub
[   74.842620] usbcore: registered new device driver usb
[   74.909213] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   74.950312] xhci_hcd 0000:01:01.0: xHCI Host Controller
[   74.950385] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 1
[   74.950808] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   74.950846] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   74.950874] usb usb1: Product: xHCI Host Controller
[   74.950897] usb usb1: Manufacturer: Linux 3.9-0.bpo.1-kirkwood xhci_hcd
[   74.950920] usb usb1: SerialNumber: 0000:01:01.0
[   74.951409] xHCI xhci_add_endpoint called for root hub
[   74.951417] xHCI xhci_check_bandwidth called for root hub
[   74.951662] hub 1-0:1.0: USB hub found
[   74.951718] hub 1-0:1.0: 2 ports detected
[   74.952003] xhci_hcd 0000:01:01.0: xHCI Host Controller
[   74.952047] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 2
[   74.952136] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[   74.952167] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   74.952194] usb usb2: Product: xHCI Host Controller
[   74.952217] usb usb2: Manufacturer: Linux 3.9-0.bpo.1-kirkwood xhci_hcd
[   74.952240] usb usb2: SerialNumber: 0000:01:01.0
[   74.954890] xHCI xhci_add_endpoint called for root hub
[   74.954900] xHCI xhci_check_bandwidth called for root hub
[   74.957249] hub 2-0:1.0: USB hub found
[   74.957323] hub 2-0:1.0: 2 ports detected
[   74.991892] ehci-orion: EHCI orion driver
[   75.073148] orion_wdt: Initial timeout 21 sec
[   75.073743] orion-ehci orion-ehci.0: EHCI Host Controller
[   75.073805] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 3
[   75.073967] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   75.091216] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   75.091327] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[   75.091359] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   75.091387] usb usb3: Product: EHCI Host Controller
[   75.091409] usb usb3: Manufacturer: Linux 3.9-0.bpo.1-kirkwood ehci_hcd
[   75.091433] usb usb3: SerialNumber: orion-ehci.0
[   75.091858] hub 3-0:1.0: USB hub found
[   75.091906] hub 3-0:1.0: 1 port detected
[   75.411222] usb 3-1: new high-speed USB device number 2 using orion-ehci
[   75.562981] usb 3-1: New USB device found, idVendor=05e3, idProduct=0608
[   75.563045] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   75.563072] usb 3-1: Product: USB2.0 Hub
[   75.564265] hub 3-1:1.0: USB hub found
[   75.564606] hub 3-1:1.0: 4 ports detected
[   76.539311] EXT4-fs (dm-1): re-mounted. Opts: (null)
[   76.856608] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[   77.571414] loop: module loaded
[   79.684918] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[   79.742391] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[   79.801780] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: (null)
[   79.858010] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null)
[   81.417984] RPC: Registered named UNIX socket transport module.
[   81.418044] RPC: Registered udp transport module.
[   81.418067] RPC: Registered tcp transport module.
[   81.418088] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   81.447038] FS-Cache: Loaded
[   81.454311] Key type dns_resolver registered
[   81.507694] FS-Cache: Netfs 'nfs' registered for caching
[   81.585295] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   86.593205] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[   88.110251] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   88.122280] NFSD: starting 90-second grace period (net c0513db8)
[   89.327218] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[  203.642744] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  203.642783] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  271.806746] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[  274.519522] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[  437.735515] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  437.735557] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  455.638653] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  455.638698] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  519.603271] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  519.603314] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  569.880774] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors
[  569.880814] mv643xx_eth_port mv643xx_eth_port.0 eth0: received packet spanning multiple descriptors

** Model information
Hardware	: QNAP TS-41x
Revision	: 0000

** Loaded modules:
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
loop
hmac
evdev
ehci_orion
sha1_generic
xhci_hcd
ehci_hcd
orion_wdt
usbcore
mv_cesa
usb_common
gpio_keys
ext4
mbcache
jbd2
dm_crypt
dm_mod
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
xor
async_tx
raid6_pq
md_mod
netconsole
configfs
cbc
xts
gf128mul
sd_mod
crc_t10dif
sata_mv
mv643xx_eth
inet_lro
libphy
libata
scsi_mod

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth0
iface eth0 inet static
	address 10.3.2.21
	netmask 255.0.0.0
	gateway 10.0.0.0
	# dns-* options are implemented by the resolvconf package, if installed
	dns-nameservers 172.16.0.1
	dns-search siccegge.de

iface eth0 inet6 static
	address 2001:4dd0:ff00:8384::2
	gateway 2001:4dd0:ff00:8384::1
	netmask 64

** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether 00:08:9b:d1:4b:10 brd ff:ff:ff:ff:ff:ff
    inet 10.3.2.21/8 brd 10.255.255.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::208:9bff:fed1:4b10/64 scope link 
       valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 00:08:9b:d1:4b:11 brd ff:ff:ff:ff:ff:ff

*** Device statistics:
Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo frame compressed multicast|bytes    packets errs drop fifo colls carrier compressed
    lo:     260       4    0    0    0     0          0         0      260       4    0    0    0     0       0          0
  eth1:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  eth0: 53460325   58081 7123 7128    0     0          0         0 39292162   55347    0    0    0     0       0          0

*** Protocol statistics:
Ip:
    46584 total packets received
    0 forwarded
    0 incoming packets discarded
    46474 incoming packets delivered
    34634 requests sent out
Icmp:
    34 ICMP messages received
    34 input ICMP message failed.
    ICMP input histogram:
        destination unreachable: 34
    0 ICMP messages sent
    0 ICMP messages failed
    ICMP output histogram:
IcmpMsg:
        InType3: 34
Tcp:
    6 active connections openings
    5 passive connection openings
    0 failed connection attempts
    0 connection resets received
    4 connections established
    43475 segments received
    54338 segments send out
    205 segments retransmited
    0 bad segments received.
    0 resets sent
Udp:
    88 packets received
    0 packets to unknown port received.
    0 packet receive errors
    95 packets sent
UdpLite:
TcpExt:
    257 delayed acks sent
    1 delayed acks further delayed because of locked socket
    Quick ack mode was activated 245 times
    3 packets directly queued to recvmsg prequeue.
    2 bytes directly received in process context from prequeue
    10000 packet headers predicted
    13129 acknowledgments not containing data payload received
    2869 predicted acknowledgments
    4 times recovered from packet loss by selective acknowledgements
    11 congestion windows recovered without slow start after partial ack
    48 fast retransmits
    98 retransmits in slow start
    56 other TCP timeouts
    255 DSACKs sent for old packets
    60 DSACKs sent for out of order packets
    10 DSACKs received
    TCPDSACKIgnoredNoUndo: 1
    TCPSackShifted: 5
    TCPSackMerged: 12
    TCPSackShiftFallback: 29
    TCPRcvCoalesce: 14782
    TCPOFOQueue: 10580
    TCPOFOMerge: 60
IpExt:
    InNoRoutes: 1
    InMcastPkts: 98
    InBcastPkts: 2779
    InOctets: 41731247
    OutOctets: 37254231
    InMcastOctets: 4164
    InBcastOctets: 358222


** PCI devices:
00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. Device [11ab:6282] (rev 01)
	Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at <ignored> (64-bit, prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [60] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

00:01.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SX7042 PCI-e 4-port SATA-II [11ab:7042] (rev 02)
	Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=1M]
	Region 2: I/O ports at 1000 [size=256]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <256ns, L1 unlimited
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Kernel driver in use: sata_mv

01:00.0 Host bridge [0600]: Marvell Technology Group Ltd. Device [11ab:6282] (rev 01)
	Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at <ignored> (64-bit, prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [60] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

01:01.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
	Subsystem: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at e8000000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [70] MSI: Enable- Count=1/4 Maskable+ 64bit+
		Address: 0000000000000000  Data: 0000
		Masking: 00000000  Pending: 00000000
	Capabilities: [a0] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [190 v1] Device Serial Number 01-01-01-01-01-01-01-01
	Kernel driver in use: xhci_hcd


** USB devices:
Bus 003 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 7.1
  APT prefers stable
  APT policy: (990, 'stable'), (500, 'testing')
Architecture: armel (armv5tel)

Kernel: Linux 3.9-0.bpo.1-kirkwood
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.9-0.bpo.1-kirkwood depends on:
ii  debconf [debconf-2.0]                   1.5.49
ii  initramfs-tools [linux-initramfs-tool]  0.112~bpo70+1
ii  kmod                                    9-3
ii  linux-base                              3.5
ii  module-init-tools                       9-3

Versions of packages linux-image-3.9-0.bpo.1-kirkwood recommends:
ii  firmware-linux-free  3.2
ii  uboot-mkimage        2012.04.01-2

Versions of packages linux-image-3.9-0.bpo.1-kirkwood suggests:
pn  debian-kernel-handbook  <none>
pn  fdutils                 <none>
pn  linux-doc-3.9           <none>

Versions of packages linux-image-3.9-0.bpo.1-kirkwood is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      <none>
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-libertas       <none>
pn  firmware-linux          <none>
pn  firmware-linux-nonfree  <none>
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information:
  linux-image-3.9-0.bpo.1-kirkwood/postinst/depmod-error-initrd-3.9-0.bpo.1-kirkwood: false
  linux-image-3.9-0.bpo.1-kirkwood/prerm/removing-running-kernel-3.9-0.bpo.1-kirkwood: true
  linux-image-3.9-0.bpo.1-kirkwood/postinst/ignoring-ramdisk:
  linux-image-3.9-0.bpo.1-kirkwood/postinst/missing-firmware-3.9-0.bpo.1-kirkwood:

--- End Message ---
--- Begin Message --- 
On Sunday 4 March 2018 20:25:31 CET Martin Michlmayr wrote:
> * Christoph Egger <christoph@christoph-egger.org> [2018-03-04 20:19]:
> > I have since then retired the QNAP
> 
> The bug is quite old and I'm not aware of any boot issues on the QNAP
> TS-41x so I think it's best to close this report.  Ok?

Agreed

  Christoph

--- End Message ---
Reply to: