Bug#858984: linux-image-4.9.0-2-amd64-unsigned: kernel radeon video driver hangs X
Package: src:linux
Version: 4.9.16-1
Severity: important
Dear Maintainer,
I have just upgraded from kernel on testing (4.9.13) to the version on
unstable just to test it, the version on testing was running fine.
The machine is running testing and is fully up to date with it. I had not
noticed any problem till now.
What I saw after upgrading to 4.9.16 and rebooting was that X came up in a
low resolution mode, not 1920x1080 like it used to. The keyboard and mouse
(both usb) were stuck, while the machine was still alive through network, so
I assume that X were stuck at that time.
The information that comes here is the one gathered booting in rescue mode.
I'll try to add the X log and more info in a later mail.
Regards.
-- Package-specific info:
** Version:
Linux version 4.9.0-2-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170321 (Debian 6.3.0-10) ) #1 SMP Debian 4.9.16-1 (2017-03-22)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=e9f30b2f-d5d3-42f7-ae36-7231d931b2cd ro single ipv6.disable=1
** Tainted: E (8192)
* Unsigned module has been loaded.
** Kernel log:
[ 1.960413] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.960491] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.960853] hub 2-1:1.0: USB hub found
[ 1.961027] hub 2-1:1.0: 8 ports detected
[ 1.966829] sdb: sdb1 sdb2 sdb3
[ 1.967472] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 1.968099] sda: sda1 sda2 sda3
[ 1.968612] sd 1:0:0:0: [sda] Attached SCSI disk
[ 2.000768] Alternate GPT is invalid, using primary GPT.
[ 2.000866] sdc: sdc1 sdc2
[ 2.001547] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[ 2.080055] tsc: Refined TSC clocksource calibration: 3092.981 MHz
[ 2.080148] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c9561128a6, max_idle_ns: 440795295901 ns
[ 2.104209] random: fast init done
[ 2.199115] md: bind<sdb2>
[ 2.200338] md: bind<sdb3>
[ 2.201761] md: bind<sdb1>
[ 2.203368] md: bind<sdc2>
[ 2.204836] md: bind<sdc1>
[ 2.205964] md: bind<sda3>
[ 2.207874] md: raid1 personality registered for level 1
[ 2.208274] md/raid1:md3: active with 2 out of 2 mirrors
[ 2.208456] created bitmap (2 pages) for device md3
[ 2.208690] md3: bitmap initialized from disk: read 1 pages, set 0 of 3469 bits
[ 2.214647] md3: detected capacity change from 0 to 232734261248
[ 2.223448] md: bind<sda2>
[ 2.224061] usb 1-1.2: new full-speed USB device number 3 using ehci-pci
[ 2.225026] md/raid1:md2: active with 2 out of 2 mirrors
[ 2.225128] md2: detected capacity change from 0 to 17163091968
[ 2.337854] usb 1-1.2: New USB device found, idVendor=076b, idProduct=3021
[ 2.337937] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.338009] usb 1-1.2: Product: Smart Card Reader USB
[ 2.338077] usb 1-1.2: Manufacturer: OMNIKEY AG
[ 2.359110] md: bind<sda1>
[ 2.361414] md/raid1:md1: active with 2 out of 2 mirrors
[ 2.361599] created bitmap (6 pages) for device md1
[ 2.361958] md1: bitmap initialized from disk: read 1 pages, set 0 of 11177 bits
[ 2.379937] md1: detected capacity change from 0 to 750021050368
[ 2.416164] usb 1-1.3: new low-speed USB device number 4 using ehci-pci
[ 2.526457] usb 1-1.3: New USB device found, idVendor=04b3, idProduct=310d
[ 2.526532] usb 1-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.530649] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.533481] usbcore: registered new interface driver usbhid
[ 2.533556] usbhid: USB HID core driver
[ 2.534937] input: HID 04b3:310d as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:04B3:310D.0001/input/input3
[ 2.535176] hid-generic 0003:04B3:310D.0001: input,hidraw0: USB HID v1.11 Mouse [HID 04b3:310d] on usb-0000:00:1a.0-1.3/input0
[ 2.608195] usb 1-1.4: new high-speed USB device number 5 using ehci-pci
[ 2.621923] md: linear personality registered for level -1
[ 2.623561] md: multipath personality registered for level -4
[ 2.625178] md: raid0 personality registered for level 0
[ 2.696152] raid6: sse2x1 gen() 5657 MB/s
[ 2.764158] raid6: sse2x1 xor() 5446 MB/s
[ 2.832177] raid6: sse2x2 gen() 10277 MB/s
[ 2.900187] raid6: sse2x2 xor() 7502 MB/s
[ 2.968206] raid6: sse2x4 gen() 11989 MB/s
[ 3.036216] raid6: sse2x4 xor() 8944 MB/s
[ 3.036288] raid6: using algorithm sse2x4 gen() 11989 MB/s
[ 3.036357] raid6: .... xor() 8944 MB/s, rmw enabled
[ 3.036428] raid6: using ssse3x2 recovery algorithm
[ 3.036722] xor: automatically using best checksumming function avx
[ 3.036983] async_tx: api initialized (async)
[ 3.038644] md: raid6 personality registered for level 6
[ 3.038706] md: raid5 personality registered for level 5
[ 3.038766] md: raid4 personality registered for level 4
[ 3.042563] md: raid10 personality registered for level 10
[ 3.046569] PM: Starting manual resume from disk
[ 3.046629] PM: Hibernation image partition 9:2 present
[ 3.046630] PM: Looking for hibernation image.
[ 3.046800] PM: Image not found (code -22)
[ 3.046801] PM: Hibernation image not present or could not be loaded.
[ 3.104352] clocksource: Switched to clocksource tsc
[ 3.138218] usb 1-1.4: New USB device found, idVendor=17ef, idProduct=7203
[ 3.138294] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.138372] usb 1-1.4: Product: U2-Ethernet
[ 3.138436] usb 1-1.4: Manufacturer: DAEC
[ 3.138504] usb 1-1.4: SerialNumber: 000000
[ 3.224267] usb 1-1.6: new low-speed USB device number 6 using ehci-pci
[ 3.236862] EXT4-fs (md1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.343243] usb 1-1.6: New USB device found, idVendor=04b3, idProduct=3025
[ 3.343317] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.343394] usb 1-1.6: Product: USB NetVista Full Width Keyboard.
[ 3.343462] usb 1-1.6: Manufacturer: LITE-ON Technology
[ 3.349412] input: LITE-ON Technology USB NetVista Full Width Keyboard. as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/0003:04B3:3025.0002/input/input4
[ 3.354396] random: crng init done
[ 3.408549] hid-generic 0003:04B3:3025.0002: input,hidraw1: USB HID v1.10 Keyboard [LITE-ON Technology USB NetVista Full Width Keyboard.] on usb-0000:00:1a.0-1.6/input0
[ 4.196714] systemd[1]: Failed to insert module 'autofs4': No such file or directory
[ 4.280050] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 4.280297] systemd[1]: Detected architecture x86-64.
[ 4.325950] systemd[1]: Set hostname to <duo>.
[ 5.273185] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 5.273844] systemd[1]: Listening on Journal Socket.
[ 5.274546] systemd[1]: Created slice System Slice.
[ 5.275673] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.276677] systemd[1]: Mounting Debug File System...
[ 5.277775] systemd[1]: Mounting Huge Pages File System...
[ 5.278286] systemd[1]: Listening on udev Control Socket.
[ 6.070326] EXT4-fs (md1): re-mounted. Opts: errors=remount-ro
[ 6.129027] systemd-journald[291]: Received request to flush runtime journal from PID 1
[ 7.579641] Adding 16760828k swap on /dev/md2. Priority:-1 extents:1 across:16760828k FS
[ 7.902317] EXT4-fs (md3): mounted filesystem with ordered data mode. Opts: acl
** Model information
sys_vendor: LENOVO
product_name: 5048R91
product_version: ThinkCentre M81
chassis_vendor: To Be Filled By O.E.M.
chassis_version: To Be Filled By O.E.M.
bios_vendor: LENOVO
bios_version: 9HKT43AUS
board_vendor: LENOVO
board_name:
board_version:
** Loaded modules:
raid10(E)
raid456(E)
async_raid6_recov(E)
async_memcpy(E)
async_pq(E)
async_xor(E)
async_tx(E)
xor(E)
raid6_pq(E)
libcrc32c(E)
raid0(E)
multipath(E)
linear(E)
ext4(E)
crc16(E)
jbd2(E)
crc32c_generic(E)
fscrypto(E)
ecb(E)
hid_generic(E)
glue_helper(E)
lrw(E)
gf128mul(E)
ablk_helper(E)
cryptd(E)
aes_x86_64(E)
mbcache(E)
usbhid(E)
hid(E)
raid1(E)
md_mod(E)
sr_mod(E)
cdrom(E)
sd_mod(E)
psmouse(E)
i2c_i801(E)
i2c_smbus(E)
ahci(E)
libahci(E)
e1000(E)
crc32c_intel(E)
libata(E)
ehci_pci(E)
skge(E)
ehci_hcd(E)
scsi_mod(E)
e1000e(E)
ptp(E)
usbcore(E)
usb_common(E)
pps_core(E)
** Network interface configuration:
auto lo
iface lo inet loopback
auto br0
iface br0 inet static
address 10.10.48.146
netmask 255.255.255.0
up /sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.10.48.1
up /sbin/route add -net 10.10.0.0 netmask 255.255.0.0 gw 10.10.48.1
bridge_hw 44:37:e6:6b:e9:48
bridge_ports eth0 usbeth0
bridge_fd 0
bridge_stp off
bridge_maxwait 0
gateway 10.10.48.1
iface br1 inet static
address 192.168.2.1
netmask 255.255.255.0
bridge_ports eth1
bridge_stp on
bridge_fd 2
bridge_maxage 6
bridge_maxwait 0
iface br2 inet static
address 0.0.0.0
netmask 255.255.255.255
bridge_ports eth1 eth2
bridge_fd 0
bridge_stp off
bridge_maxwait 0
iface wlan0 inet manual
wpa-driver wext
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
down /usr/local/sbin/down_if
iface wlan1 inet manual
wpa-driver wext
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
down /usr/local/sbin/down_if
iface wlan2 inet manual
wpa-driver wext
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
down /usr/local/sbin/down_if
iface monitorizar inet manual
up pump -i wlan0 --no-dns --no-ntp --route-metric 54
up ifconfig wlan0:0 172.22.11.123 netmask 255.255.255.0
down pump -k
down /usr/local/sbin/down_if
iface default inet manual
up pump -i wlan0 --no-dns --no-ntp --route-metric 54
down pump -k
down /usr/local/sbin/down_if
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:0a:5e:65:57:d6 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 44:37:e6:6b:e9:48 brd ff:ff:ff:ff:ff:ff
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:02:b3:c6:f1:29 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
Forwarding: 2
0 total packets received
0 forwarded
0 incoming packets discarded
0 incoming packets delivered
0 requests sent out
72 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
0 active connection openings
0 passive connection openings
0 failed connection attempts
0 connection resets received
0 connections established
0 segments received
0 segments sent out
0 segments retransmitted
0 bad segments received
0 resets sent
Udp:
0 packets received
0 packets to unknown port received
0 packet receive errors
0 packets sent
0 receive buffer errors
0 send buffer errors
UdpLite:
TcpExt:
0 packet headers predicted
IpExt:
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Subsystem: Lenovo 2nd Generation Core Processor Family DRAM Controller [17aa:3077]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Lenovo Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [17aa:3077]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Lenovo 6 Series/C200 Series Chipset Family MEI Controller [17aa:3077]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe72a000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:16.3 Serial controller [0700]: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller [8086:1c3d] (rev 04) (prog-if 02 [16550])
Subsystem: Lenovo 6 Series/C200 Series Chipset Family KT Controller [17aa:3077]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at f0a0 [size=8]
Region 1: Memory at fe729000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 05)
Subsystem: Lenovo 82579LM Gigabit Network Connection [17aa:3077]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 25
Region 0: Memory at fe700000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fe728000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f040 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41a1
Capabilities: [e0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: Lenovo 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [17aa:3077]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe727000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: Lenovo 6 Series/C200 Series Chipset Family High Definition Audio Controller [17aa:3077]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe720000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Lenovo 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [17aa:3077]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe726000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Lenovo 82801 PCI Bridge [17aa:3077]
00:1f.0 ISA bridge [0601]: Intel Corporation Q65 Express Chipset Family LPC Controller [8086:1c4c] (rev 05)
Subsystem: Lenovo Q65 Express Chipset Family LPC Controller [17aa:3077]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo 6 Series/C200 Series Chipset Family SATA AHCI Controller [17aa:3077]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 26
Region 0: I/O ports at f090 [size=8]
Region 1: I/O ports at f080 [size=4]
Region 2: I/O ports at f070 [size=8]
Region 3: I/O ports at f060 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at fe725000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41e1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: Lenovo 6 Series/C200 Series Chipset Family SMBus Controller [17aa:3077]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe724000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Cedar [Radeon HD 5000/6000/7350/8350 Series] [1002:68f9] (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. [MSI] Radeon HD 5450 [1462:2181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe620000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [150 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Cedar HDMI Audio [Radeon HD 5400/6300/7300 Series] [1002:aa68]
Subsystem: Micro-Star International Co., Ltd. [MSI] Cedar HDMI Audio [Radeon HD 5400/6300/7300 Series] [1462:aa68]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fe640000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [150 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
02:00.0 Ethernet controller [0200]: Intel Corporation 82544EI Gigabit Ethernet Controller (Copper) [8086:1008] (rev 02)
Subsystem: Intel Corporation PRO/1000 XT Server Adapter [8086:1107]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe560000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fe540000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d100 [size=32]
Expansion ROM at fe520000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: e1000
02:01.0 Ethernet controller [0200]: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] [10b7:1700] (rev 10)
Subsystem: 3Com Corporation 3C941 Gigabit LOM Ethernet Adapter [10b7:0020]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fe580000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d000 [size=256]
Expansion ROM at fe500000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: 3Com Gigabit NIC (3C2000)
Read-only fields:
[PN] Part number: 40-0778-000
[EC] Engineering changes: Rev. 1.2
[MN] Manufacture ID: 33 43 6f 6d
[SN] Serial number: HZKQ6557D6
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 41 byte(s) reserved
Read/write fields:
[MC] Unknown: 29 04 02 00 00 00 01 00
[RW] Read-write area: 110 byte(s) free
End
Kernel driver in use: skge
** USB devices:
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 006: ID 04b3:3025 IBM Corp. NetVista Full Width Keyboard
Bus 001 Device 005: ID 17ef:7203 Lenovo Ethernet adapter [U2L 100P-Y1]
Bus 001 Device 004: ID 04b3:310d IBM Corp.
Bus 001 Device 003: ID 076b:3021 OmniKey AG CardMan 3121
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 9.0
APT prefers testing
APT policy: (990, 'testing'), (500, 'stable-updates'), (500, 'unstable'), (500, 'stable'), (500, 'oldstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.9.0-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=gl_ES.UTF-8, LC_CTYPE=gl_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.9.0-2-amd64-unsigned depends on:
ii initramfs-tools [linux-initramfs-tool] 0.127
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.9.0-2-amd64-unsigned recommends:
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2.3
Versions of packages linux-image-4.9.0-2-amd64-unsigned suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta3-5
pn linux-doc-4.9 <none>
Versions of packages linux-image-4.9.0-2-amd64-unsigned is related to:
ii firmware-amd-graphics 20161130-2
pn firmware-atheros <none>
ii firmware-bnx2 20161130-2
ii firmware-bnx2x 20161130-2
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux-nonfree 20161130-2
ii firmware-misc-nonfree 20161130-2
pn firmware-myricom <none>
pn firmware-netxen <none>
ii firmware-qlogic 20161130-2
ii firmware-realtek 20161130-2
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: