Bug#838890: linux-image-4.7.0-0.bpo.1-686-pae-unsigned: resume after hibernate with s2disk reboots the system
Package: src:linux
Version: 4.7.2-1~bpo8+1
Severity: normal
Dear Maintainer,
I hibernated with s2disk in a file partition.
Restarting the system, resuming works fine but at the end of the resume step,
the computer reboots and the previous session is lost.
I cannot see possible errors messages.
All worked fine with Linux-image 4.6 from jessie-backports.
Regards.
cat /etc/uswsusp.conf
# /etc/uswsusp.conf(5) -- Configuration file for s2disk/s2both
resume device = /dev/sdb1
compress = y
early writeout = y
image size = 480954449
RSA key file = /etc/uswsusp.key
shutdown method = platform
resume offset = 954368
-- Package-specific info:
** Version:
Linux version 4.7.0-0.bpo.1-686-pae (debian-kernel@lists.debian.org) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Debian 4.7.2-1~bpo8+1 (2016-09-07)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.7.0-0.bpo.1-686-pae root=UUID=2ed3bc82-5cc0-4529-a13c-2e6f80b5b588 ro resume=/dev/sdb1 quiet
** Tainted: E (8192)
* Unsigned module has been loaded (currently expected).
** Kernel log:
[ 7.701863] eeepc_laptop: Hotkey init flags 0x41
[ 7.727896] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.755420] [drm] Initialized drm 1.1.0 20060810
[ 7.907993] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 7.908075] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 7.908085] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
[ 7.908092] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 7.908099] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 7.915996] snd_hda_codec_realtek hdaudioC0D0: Mic=0x18
[ 7.916151] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
[ 7.933844] ACPI: Battery Slot [BAT0] (battery present)
[ 7.934352] ACPI: AC Adapter [AC0] (off-line)
[ 7.953003] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 7.956416] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 7.956685] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 7.977133] pci 0000:00:00.0: Intel 945GME Chipset
[ 7.977182] pci 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[ 7.977311] pci 0000:00:00.0: detected 8192K stolen memory
[ 7.977395] [drm] Memory usable by graphics device = 256M
[ 7.977407] [drm] Replacing VGA console driver
[ 7.979420] Console: switching to colour dummy device 80x25
[ 7.996872] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.996883] [drm] Driver supports precise vblank timestamp query.
[ 8.002652] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 8.086482] intel_rng: FWH not detected
[ 8.088352] [drm] RC6 disabled, disabling runtime PM support
[ 8.088445] [drm] initialized overlay support
[ 8.113854] fbcon: inteldrmfb (fb0) is primary device
[ 8.251359] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 8.251563] sd 1:0:1:0: Attached scsi generic sg1 type 0
[ 8.353606] rt2800pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 8.353932] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[ 8.375460] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0003 detected
[ 8.417346] Bluetooth: Core ver 2.21
[ 8.417415] NET: Registered protocol family 31
[ 8.417417] Bluetooth: HCI device and connection manager initialized
[ 8.417430] Bluetooth: HCI socket layer initialized
[ 8.417440] Bluetooth: L2CAP socket layer initialized
[ 8.417475] Bluetooth: SCO socket layer initialized
[ 8.442603] media: Linux media interface: v0.10
[ 8.450738] usbcore: registered new interface driver btusb
[ 8.472333] Linux video capture interface: v2.00
[ 8.520446] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8.524252] uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
[ 8.543178] uvcvideo 1-8:1.0: Entity type for entity Extension 5 was not initialized!
[ 8.543193] uvcvideo 1-8:1.0: Entity type for entity Extension 4 was not initialized!
[ 8.543203] uvcvideo 1-8:1.0: Entity type for entity Processing 3 was not initialized!
[ 8.543212] uvcvideo 1-8:1.0: Entity type for entity Camera 1 was not initialized!
[ 8.543777] input: CNF7129 as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input11
[ 8.543960] usbcore: registered new interface driver uvcvideo
[ 8.543962] USB Video Class driver (1.1.1)
[ 8.550357] input: PC Speaker as /devices/platform/pcspkr/input/input12
[ 8.821436] intel_powerclamp: No package C-state available
[ 8.922585] intel_powerclamp: No package C-state available
[ 8.922585] [drm] Initialized i915 1.6.0 20160425 for 0000:00:02.0 on minor 0
[ 8.923093] Console: switching to colour frame buffer device 128x37
[ 8.935343] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000087F (\PMIO) (20160422/utaddress-255)
[ 8.935358] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000087F (\_SB.PCI0.SBRG.PMS0) (20160422/utaddress-255)
[ 8.935362] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.935379] ACPI Warning: SystemIO range 0x00000000000004B0-0x00000000000004BF conflicts with OpRegion 0x0000000000000480-0x00000000000004BF (\_SB.PCI0.SBRG.GPBX) (20160422/utaddress-255)
[ 8.935382] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.935397] ACPI Warning: SystemIO range 0x0000000000000480-0x00000000000004AF conflicts with OpRegion 0x0000000000000480-0x00000000000004BF (\_SB.PCI0.SBRG.GPBX) (20160422/utaddress-255)
[ 8.935399] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.935401] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 8.935748] ACPI Warning: SystemIO range 0x0000000000000400-0x000000000000041F conflicts with OpRegion 0x0000000000000400-0x000000000000040F (\SMRG) (20160422/utaddress-255)
[ 8.935761] ACPI Warning: SystemIO range 0x0000000000000400-0x000000000000041F conflicts with OpRegion 0x0000000000000400-0x000000000000040F (\_SB.PCI0.SBRG.SMRG) (20160422/utaddress-255)
[ 8.935765] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.944904] leds_ss4200: no LED devices found
[ 8.965628] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 9.358228] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 9.920846] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.006954] eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
[ 10.013691] eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
[ 10.013714] eeepc_laptop: Get control methods supported: 0x6101713
[ 10.017215] input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input13
[ 10.072084] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 10.431854] iTCO_vendor_support: vendor-support=0
[ 10.436277] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 10.436411] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0860)
[ 10.438435] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.512223] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.568501] Adding 1733004k swap on /home/decharge/fichier_de_swap. Priority:-1 extents:77 across:13828096k SSFS
[ 12.240353] pci 0000:00:1e.0: PCI bridge to [bus 06]
[ 12.346206] pci 0000:00:1e.0: PCI bridge to [bus 06]
[ 12.347051] eeepc_laptop: BIOS says wireless lan is unblocked, but the pci device is absent
[ 12.347062] eeepc_laptop: skipped wireless hotplug as probably inappropriate for this model
[ 12.418990] apm: BIOS not found.
[ 14.568309] pci 0000:00:1e.0: PCI bridge to [bus 06]
[ 14.676196] pci 0000:00:1e.0: PCI bridge to [bus 06]
[ 16.233720] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 16.238241] rt2800pci 0000:01:00.0: firmware: direct-loading firmware rt2860.bin
[ 16.238269] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[ 18.069879] wlan0: authenticate with 84:74:2a:4d:c1:25
[ 18.077514] wlan0: send auth to 84:74:2a:4d:c1:25 (try 1/3)
[ 18.082199] wlan0: authenticated
[ 18.088186] wlan0: associate with 84:74:2a:4d:c1:25 (try 1/3)
[ 18.091867] wlan0: RX AssocResp from 84:74:2a:4d:c1:25 (capab=0x431 status=0 aid=1)
[ 18.092192] wlan0: associated
[ 18.248942] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
[ 212.200219] perf: interrupt took too long (2540 > 2500), lowering kernel.perf_event_max_sample_rate to 78500
** Model information
** Loaded modules:
hmac(E)
drbg(E)
ansi_cprng(E)
ctr(E)
ccm(E)
binfmt_misc(E)
xt_hl(E)
ip6t_rt(E)
nf_conntrack_ipv6(E)
nf_defrag_ipv6(E)
ip6t_REJECT(E)
nf_reject_ipv6(E)
xt_limit(E)
xt_tcpudp(E)
xt_addrtype(E)
nf_conntrack_ipv4(E)
nf_defrag_ipv4(E)
xt_conntrack(E)
ipt_REJECT(E)
nf_reject_ipv4(E)
ip6table_filter(E)
ip6_tables(E)
iTCO_wdt(E)
iTCO_vendor_support(E)
nf_conntrack_netbios_ns(E)
nf_conntrack_broadcast(E)
nf_nat_ftp(E)
nf_nat(E)
nf_conntrack_ftp(E)
nf_conntrack(E)
iptable_filter(E)
ip_tables(E)
x_tables(E)
coretemp(E)
joydev(E)
evdev(E)
serio_raw(E)
pcspkr(E)
uvcvideo(E)
videobuf2_vmalloc(E)
videobuf2_memops(E)
arc4(E)
i2c_i801(E)
videobuf2_v4l2(E)
videobuf2_core(E)
videodev(E)
media(E)
btusb(E)
btrtl(E)
btbcm(E)
btintel(E)
bluetooth(E)
rt2800pci(E)
rt2800mmio(E)
rt2800lib(E)
rt2x00pci(E)
rt2x00mmio(E)
rt2x00lib(E)
eeprom_93cx6(E)
sg(E)
mac80211(E)
lpc_ich(E)
mfd_core(E)
cfg80211(E)
rng_core(E)
crc_ccitt(E)
snd_hda_codec_realtek(E)
snd_hda_codec_generic(E)
i915(E)
snd_hda_intel(E)
snd_hda_codec(E)
snd_hda_core(E)
snd_hwdep(E)
snd_pcm(E)
snd_timer(E)
drm_kms_helper(E)
ac(E)
battery(E)
snd(E)
soundcore(E)
drm(E)
shpchp(E)
i2c_algo_bit(E)
eeepc_laptop(E)
sparse_keymap(E)
rfkill(E)
video(E)
button(E)
acpi_cpufreq(E)
tpm_tis(E)
tpm(E)
loop(E)
fuse(E)
parport_pc(E)
ppdev(E)
lp(E)
parport(E)
autofs4(E)
ext4(E)
crc16(E)
jbd2(E)
mbcache(E)
sd_mod(E)
ata_generic(E)
psmouse(E)
ata_piix(E)
libata(E)
scsi_mod(E)
uhci_hcd(E)
ehci_pci(E)
ehci_hcd(E)
usbcore(E)
usb_common(E)
atl1e(E)
thermal(E)
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GSE Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc80 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f7f80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:831a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-401fffff
Prefetchable memory behind bridge: 0000000040200000-00000000403fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbf00000-fbffffff
Prefetchable memory behind bridge: 0000000040400000-00000000405fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 40600000-407fffff
Prefetchable memory behind bridge: 0000000040800000-00000000409fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-fbefffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] [8086:27c4] (rev 02) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0400 [size=32]
01:00.0 Network controller [0280]: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe [1814:0781]
Subsystem: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe [1814:2790]
Physical Slot: eeepc-wifi
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: rt2800pci
04:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet [1969:1026] (rev b0)
Subsystem: ASUSTeK Computer Inc. Device [1043:8324]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ec80 [size=128]
Capabilities: <access denied>
Kernel driver in use: ATL1E
** USB devices:
Bus 001 Device 003: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 0b05:b700 ASUSTek Computer, Inc. Broadcom Bluetooth 2.1
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.6
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 4.7.0-0.bpo.1-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.utf8, LC_CTYPE=fr_FR.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.7.0-0.bpo.1-686-pae-unsigned depends on:
ii initramfs-tools [linux-initramfs-tool] 0.120+deb8u2
ii kmod 18-3
ii linux-base 4.3~bpo8+1
Versions of packages linux-image-4.7.0-0.bpo.1-686-pae-unsigned recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.1.0-2~bpo8+1
Versions of packages linux-image-4.7.0-0.bpo.1-686-pae-unsigned suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22+deb8u1
pn linux-doc-4.7 <none>
Versions of packages linux-image-4.7.0-0.bpo.1-686-pae-unsigned is related to:
ii firmware-amd-graphics 20160110-1~bpo8+1
ii firmware-atheros 20160110-1~bpo8+1
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux-nonfree 20160110-1~bpo8+1
ii firmware-misc-nonfree 20160110-1~bpo8+1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: