Bug#824920: linux-image-4.5.0-2-armmp-lpae: Failed to setup eth0 on Cubietruck
Package: linux-image-4.5.0-2-armmp-lpae
Version: 4.5.4-1
Severity: normal
Hello,
linux version 4.5 failed to setup eth0 on my Cubietruck, with some message in dmesg:
[ 19.502508] libphy: PHY stmmac-0:ffffffff not found
[ 19.507569] eth0: Could not attach to PHY
[ 19.511696] stmmac_open: Cannot attach to PHY (error: -19)
There's no such problem with 4.4.
The full dmesg output is attached.
Thanks
-- System Information:
Debian Release: stretch/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (1, 'experimental')
Architecture: armhf (armv7l)
Kernel: Linux 4.4.0-1-armmp-lpae (SMP w/2 CPU cores)
Locale: LANG=zh_CN.UTF-8, LC_CTYPE=zh_CN.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.5.0-2-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 5.3.1 20160509 (Debian 5.3.1-19) ) #1 SMP Debian 4.5.4-1 (2016-05-16)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Cubietech Cubietruck
[ 0.000000] cma: Reserved 16 MiB at 0x00000000be800000
[ 0.000000] Forcing write-allocate cache policy for SMP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 523520
[ 0.000000] free_area_init_node: node 0, pgdat c0baccc0, node_mem_map eedf9000
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] HighMem zone: 326912 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] PERCPU: Embedded 12 pages/cpu @eedbf000 s20044 r8192 d20916 u49152
[ 0.000000] pcpu-alloc: s20044 r8192 d20916 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 521792
[ 0.000000] Kernel command line: console=ttyS0,115200 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1280x1024p60 root=/dev/mmcblk0p1 rootwait panic=10
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2031316K/2094080K available (7520K kernel code, 943K rwdata, 2580K rodata, 944K init, 398K bss, 46380K reserved, 16384K cma-reserved, 1291264K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc09e52d8 (10101 kB)
.init : 0xc09e6000 - 0xc0ad2000 ( 944 kB)
.data : 0xc0ad2000 - 0xc0bbdef4 ( 944 kB)
.bss : 0xc0bc0000 - 0xc0c238cc ( 399 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000024] Switching to timer-based delay loop, resolution 41ns
[ 0.002182] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002934] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 12741736309 ns
[ 0.003727] Console: colour dummy device 80x30
[ 0.003852] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.003870] pid_max: default: 32768 minimum: 301
[ 0.004114] Security Framework initialized
[ 0.004130] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004174] AppArmor: AppArmor disabled by boot time parameter
[ 0.004248] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004262] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.005267] Disabling memory control group subsystem
[ 0.005421] CPU: Testing write buffer coherency: ok
[ 0.005479] ftrace: allocating 25902 entries in 76 pages
[ 0.047937] /cpus/cpu@0 missing clock-frequency property
[ 0.047980] /cpus/cpu@1 missing clock-frequency property
[ 0.047995] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.048094] Setting up static identity map for 0x400082c0 - 0x40008358
[ 0.054777] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.054922] Brought up 2 CPUs
[ 0.054951] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.054959] CPU: All CPU(s) started in HYP mode.
[ 0.054965] CPU: Virtualization extensions available.
[ 0.055887] devtmpfs: initialized
[ 0.065397] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.066286] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.067353] pinctrl core: initialized pinctrl subsystem
[ 0.069423] NET: Registered protocol family 16
[ 0.071532] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.084550] No ATAGs?
[ 0.084607] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.084622] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.086245] Serial: AMBA PL011 UART driver
[ 0.104866] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.107938] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[ 0.108086] reg-fixed-voltage usb0-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb0_vbus_pin@0, deferring probe
[ 0.108126] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.108162] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[ 0.111946] vgaarb: loaded
[ 0.113254] media: Linux media interface: v0.10
[ 0.113322] Linux video capture interface: v2.00
[ 0.113426] pps_core: LinuxPPS API ver. 1 registered
[ 0.113435] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.113467] PTP clock support registered
[ 0.115528] clocksource: Switched to clocksource arch_sys_counter
[ 0.167163] VFS: Disk quotas dquot_6.6.0
[ 0.167297] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.169030] simple-framebuffer bfd00000.framebuffer: framebuffer at 0xbfd00000, 0x300000 bytes, mapped to 0xf0900000
[ 0.169052] simple-framebuffer bfd00000.framebuffer: format=x8r8g8b8, mode=1024x768x32, linelength=4096
[ 0.183708] Console: switching to colour frame buffer device 128x48
[ 0.197373] simple-framebuffer bfd00000.framebuffer: fb0: simplefb registered!
[ 0.211277] NET: Registered protocol family 2
[ 0.212344] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.212445] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.212574] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.212680] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.212745] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.213258] NET: Registered protocol family 1
[ 0.213334] PCI: CLS 0 bytes, default 64
[ 0.213989] Unpacking initramfs...
[ 1.411154] Freeing initrd memory: 14456K (c91e2000 - ca000000)
[ 1.412709] kvm [1]: interrupt-controller@1c84000 IRQ52
[ 1.413180] kvm [1]: timer IRQ19
[ 1.413207] kvm [1]: 8-bit VMID
[ 1.413215] kvm [1]: Hyp mode initialized successfully
[ 1.414155] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 1.416391] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.416564] audit: initializing netlink subsys (disabled)
[ 1.416668] audit: type=2000 audit(1.396:1): initialized
[ 1.417662] Initialise system trusted keyring
[ 1.418449] zbud: loaded
[ 1.422209] Key type asymmetric registered
[ 1.422240] Asymmetric key parser 'x509' registered
[ 1.422353] bounce: pool size: 64 pages
[ 1.422509] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.422740] io scheduler noop registered
[ 1.422760] io scheduler deadline registered
[ 1.422806] io scheduler cfq registered (default)
[ 1.427961] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 1.442849] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.445536] console [ttyS0] disabled
[ 1.465814] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 44, base_baud = 1500000) is a U6_16550A
[ 2.200776] console [ttyS0] enabled
[ 2.205301] Serial: AMBA driver
[ 2.212918] mousedev: PS/2 mouse device common for all mice
[ 2.221027] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 2.227858] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 2.234321] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.242408] NET: Registered protocol family 10
[ 2.248227] mip6: Mobile IPv6
[ 2.251223] NET: Registered protocol family 17
[ 2.255766] mpls_gso: MPLS GSO support
[ 2.260136] ThumbEE CPU extension supported.
[ 2.264503] Registering SWP/SWPB emulation handler
[ 2.270480] registered taskstats version 1
[ 2.274703] Loading compiled-in X.509 certificates
[ 2.281735] Loaded X.509 cert 'Debian Project: Ben Hutchings: 008a018dca80932630'
[ 2.289410] zswap: loaded using pool lzo/zbud
[ 2.297533] sunxi-rtc 1c20d00.rtc: setting system clock to 2016-05-21 10:37:36 UTC (1463827056)
[ 2.313747] PM: Hibernation image not present or could not be loaded.
[ 2.313800] vcc3v0: disabling
[ 2.316869] vcc3v3: disabling
[ 2.319861] vcc5v0: disabling
[ 2.322829] ahci-5v: disabling
[ 2.325904] usb0-vbus: disabling
[ 2.329136] usb1-vbus: disabling
[ 2.332379] usb2-vbus: disabling
[ 2.337344] Freeing unused kernel memory: 944K (c09e6000 - c0ad2000)
[ 2.464579] random: systemd-udevd urandom read with 0 bits of entropy available
[ 2.755364] extcon: module verification failed: signature and/or required key missing - tainting kernel
[ 2.766565] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 2.802778] usbcore: registered new interface driver usbfs
[ 2.808560] usbcore: registered new interface driver hub
[ 2.809878] SCSI subsystem initialized
[ 2.821710] sunxi-mmc 1c0f000.mmc: base:0xf08d6000 irq:26
[ 2.828963] usbcore: registered new device driver usb
[ 2.841418] sunxi-mmc 1c12000.mmc: allocated mmc-pwrseq
[ 2.853469] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.867848] libata version 3.00 loaded.
[ 2.871766] ehci-platform: EHCI generic platform driver
[ 2.872375] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.873633] ohci-platform: OHCI generic platform driver
[ 2.899866] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.908094] sunxi-mmc 1c12000.mmc: base:0xf08f4000 irq:27
[ 2.916875] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 2.926517] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 1
[ 2.934445] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 8, RTO !!
[ 2.935128] mmc0: new high speed SDHC card at address 0007
[ 2.948587] ohci-platform 1c14400.usb: irq 30, io mem 0x01c14400
[ 2.957405] mmcblk0: mmc0:0007 SD32G 29.9 GiB
[ 2.965042] mmcblk0: p1
[ 2.972697] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 2.986506] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 3.001230] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 3.012008] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.018979] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.026333] usb usb1: Product: Generic Platform OHCI controller
[ 3.032366] usb usb1: Manufacturer: Linux 4.5.0-2-armmp-lpae ohci_hcd
[ 3.038915] usb usb1: SerialNumber: 1c14400.usb
[ 3.038943] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 3.055664] hub 1-0:1.0: USB hub found
[ 3.059549] hub 1-0:1.0: 1 port detected
[ 3.074952] mmc1: new high speed SDIO card at address 0001
[ 3.111719] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 3.119308] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 3.125376] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 3.134519] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 3.145217] scsi host0: ahci-sunxi
[ 3.149371] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 32
[ 3.158560] sun7i-dwmac 1c50000.ethernet: no regulator found
[ 3.165398] sun7i-dwmac 1c50000.ethernet: no reset control found
[ 3.171621] Ring mode enabled
[ 3.174688] No HW DMA feature register supported
[ 3.179289] Normal descriptors
[ 3.182669] TX Checksum insertion supported
[ 3.188669] ehci-platform 1c14000.usb: EHCI Host Controller
[ 3.194416] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 2
[ 3.204160] ehci-platform 1c14000.usb: irq 29, io mem 0x01c14000
[ 3.219644] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 3.226293] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.233168] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.240462] usb usb2: Product: EHCI Host Controller
[ 3.245400] usb usb2: Manufacturer: Linux 4.5.0-2-armmp-lpae ehci_hcd
[ 3.251897] usb usb2: SerialNumber: 1c14000.usb
[ 3.257759] hub 2-0:1.0: USB hub found
[ 3.261739] hub 2-0:1.0: 1 port detected
[ 3.266855] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 3.272572] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3
[ 3.281174] ehci-platform 1c1c000.usb: irq 33, io mem 0x01c1c000
[ 3.295647] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 3.302239] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.309137] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.316443] usb usb3: Product: EHCI Host Controller
[ 3.321386] usb usb3: Manufacturer: Linux 4.5.0-2-armmp-lpae ehci_hcd
[ 3.327883] usb usb3: SerialNumber: 1c1c000.usb
[ 3.333631] hub 3-0:1.0: USB hub found
[ 3.337577] hub 3-0:1.0: 1 port detected
[ 3.342693] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 3.352458] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 3.365176] ohci-platform 1c1c400.usb: irq 34, io mem 0x01c1c400
[ 3.427809] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.434643] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.441888] usb usb4: Product: Generic Platform OHCI controller
[ 3.447828] usb usb4: Manufacturer: Linux 4.5.0-2-armmp-lpae ohci_hcd
[ 3.454284] usb usb4: SerialNumber: 1c1c400.usb
[ 3.462326] hub 4-0:1.0: USB hub found
[ 3.466232] hub 4-0:1.0: 1 port detected
[ 3.470321] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.969119] ata1.00: ATA-8: KINGSTON SV300S37A120G, 541ABBF0, max UDMA/133
[ 3.976080] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 3.989101] ata1.00: configured for UDMA/133
[ 3.994343] scsi 0:0:0:0: Direct-Access ATA KINGSTON SV300S3 BBF0 PQ: 0 ANSI: 5
[ 4.035664] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 4.043662] sd 0:0:0:0: [sda] Write Protect is off
[ 4.048490] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.048629] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.062127] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.291669] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[ 4.974693] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 4.993751] systemd[1]: Detected architecture arm.
[ 5.029616] systemd[1]: Set hostname to <cubie>.
[ 5.839888] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.863844] systemd[1]: Reached target Swap.
[ 5.876522] systemd[1]: Listening on Journal Audit Socket.
[ 5.892093] systemd[1]: Listening on Syslog Socket.
[ 5.903792] systemd[1]: Reached target Encrypted Volumes.
[ 5.915750] systemd[1]: Reached target Remote File Systems (Pre).
[ 5.932538] systemd[1]: Created slice User and Session Slice.
[ 5.948163] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 5.972077] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.987786] systemd[1]: Reached target Paths.
[ 5.999971] systemd[1]: Listening on udev Kernel Socket.
[ 6.012554] systemd[1]: Created slice System Slice.
[ 6.027845] systemd[1]: Reached target Slices.
[ 6.040590] systemd[1]: Created slice system-getty.slice.
[ 6.056586] systemd[1]: Created slice system-tor.slice.
[ 6.072570] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 6.088060] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.104019] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 6.120056] systemd[1]: Listening on udev Control Socket.
[ 6.132128] systemd[1]: Listening on Journal Socket.
[ 6.156509] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 6.184088] systemd[1]: Starting Journal Service...
[ 6.201759] systemd[1]: Mounting Debug File System...
[ 6.220844] systemd[1]: Mounting Huge Pages File System...
[ 6.271815] systemd[1]: Starting Load Kernel Modules...
[ 6.277922] EXT4-fs (mmcblk0p1): re-mounted. Opts: data=writeback,commit=600,errors=remount-ro
[ 6.312266] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.368751] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 6.416135] systemd[1]: Mounting Temporary Directory...
[ 6.429300] systemd[1]: Reached target Remote File Systems.
[ 6.476935] systemd[1]: Mounted Huge Pages File System.
[ 6.492054] systemd[1]: Mounted POSIX Message Queue File System.
[ 6.507999] systemd[1]: Mounted Debug File System.
[ 6.519999] systemd[1]: Mounted Temporary Directory.
[ 6.537655] systemd[1]: Started Remount Root and Kernel File Systems.
[ 6.556375] systemd[1]: Started Load Kernel Modules.
[ 6.574758] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 6.988644] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 7.009817] systemd[1]: Starting Apply Kernel Variables...
[ 7.037015] systemd[1]: Starting Load/Save Random Seed...
[ 7.124690] systemd[1]: Starting udev Coldplug all Devices...
[ 7.151379] systemd[1]: Started Apply Kernel Variables.
[ 7.165920] systemd[1]: Started Load/Save Random Seed.
[ 7.312129] systemd[1]: Started Create Static Device Nodes in /dev.
[ 7.525435] systemd[1]: Reached target Local File Systems (Pre).
[ 7.560847] systemd[1]: Starting udev Kernel Device Manager...
[ 7.620314] systemd[1]: Started udev Coldplug all Devices.
[ 7.786297] systemd[1]: Started udev Kernel Device Manager.
[ 7.947627] systemd[1]: Started Journal Service.
[ 8.278331] systemd-journald[149]: Received request to flush runtime journal from PID 1
[ 9.187510] random: nonblocking pool is initialized
[ 9.908005] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 10.880857] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 11.034906] sun4i-ss 1c15000.crypto-engine: no reset control found
[ 11.042824] sun4i-ss 1c15000.crypto-engine: Die ID 0
[ 11.162887] axp20x 0-0034: AXP20x variant AXP209 found
[ 11.207944] axp20x 0-0034: AXP20X driver loaded
[ 11.879475] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[ 11.893895] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[ 12.187621] raid6: int32x1 gen() 130 MB/s
[ 12.259757] raid6: int32x1 xor() 107 MB/s
[ 12.331663] raid6: int32x2 gen() 167 MB/s
[ 12.403674] raid6: int32x2 xor() 115 MB/s
[ 12.475927] raid6: int32x4 gen() 167 MB/s
[ 12.547711] raid6: int32x4 xor() 117 MB/s
[ 12.619689] raid6: int32x8 gen() 171 MB/s
[ 12.691707] raid6: int32x8 xor() 108 MB/s
[ 12.695991] raid6: using algorithm int32x8 gen() 171 MB/s
[ 12.701395] raid6: .... xor() 108 MB/s, rmw enabled
[ 12.706279] raid6: using intx1 recovery algorithm
[ 12.904843] xor: measuring software checksum speed
[ 12.947510] arm4regs : 1185.000 MB/sec
[ 12.991560] 8regs : 826.000 MB/sec
[ 13.035619] 32regs : 795.000 MB/sec
[ 13.039918] xor: using function: arm4regs (1185.000 MB/sec)
[ 13.443004] usbcore: registered new interface driver brcmfmac
[ 13.831029] brcmfmac_sdio mmc1:0001:1: firmware: direct-loading firmware brcm/brcmfmac43362-sdio.bin
[ 13.847097] brcmfmac_sdio mmc1:0001:1: firmware: direct-loading firmware brcm/brcmfmac43362-sdio.txt
[ 13.865579] Btrfs loaded
[ 13.869687] BTRFS: device label tank devid 1 transid 136454 /dev/sda
[ 14.114573] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
[ 14.143427] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code
[ 14.239859] BTRFS info (device sda): use ssd allocation scheme
[ 14.245797] BTRFS info (device sda): turning on discard
[ 14.251063] BTRFS info (device sda): disk space caching is enabled
[ 16.954837] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code
[ 18.710023] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.798302] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 19.502508] libphy: PHY stmmac-0:ffffffff not found
[ 19.507569] eth0: Could not attach to PHY
[ 19.511696] stmmac_open: Cannot attach to PHY (error: -19)
Reply to: