--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.32-5-sparc64: text console goes blank after ca. 10-15 minutes and doesn't unblank anymore
- From: Axel Beckert <abe@debian.org>
- Date: Wed, 19 Jan 2011 01:21:45 +0100
- Message-id: <87mxmxyc86.fsf@hz.deuxchevaux.org>
Package: linux-2.6
Version: 2.6.32-30
Severity: important
When I work on the framebuffer text console on my UltraSPARC 10 with an
13W3 monitor as primary screen, the console blanks after approximately
10 or 15 minutes even if I'm typing on that console at that moment.
Switching back to X with Alt-F7 works fine and I can continue to work
there, but switching back to the text console with e.g. Ctrl-Alt-F1
doesn't unblank it either. It remains black and unusable until the
system rebooted.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-sparc64 (Debian 2.6.32-30) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Wed Jan 12 04:10:58 UTC 2011
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-sparc64 root=/dev/mapper/vg0-root ro video=atyfb:off
** Not tainted
** Kernel log:
[ 4.867534] pata_cmd64x: active 3 recovery 1 setup 1.
[ 4.867561] pata_cmd64x: active 3 recovery 1 setup 1.
[ 4.882076] ata1.00: configured for MWDMA2
[ 4.884847] scsi: waiting for bus probes to complete ...
[ 12.221115] scsi 1:0:0:0: Direct-Access ATA ST39120A 3.11 PQ: 0 ANSI: 5
[ 12.225409] pata_cmd64x: active 10 recovery 10 setup 3.
[ 12.225435] pata_cmd64x: active 10 recovery 10 setup 3.
[ 12.381363] ata2.00: ATAPI: CRD-8322B, 1.05, max MWDMA2
[ 12.384299] pata_cmd64x: active 3 recovery 1 setup 1.
[ 12.384324] pata_cmd64x: active 3 recovery 1 setup 1.
[ 12.397175] ata2.00: configured for MWDMA2
[ 12.401846] scsi 2:0:0:0: CD-ROM LG CD-ROM CRD-8322B 1.05 PQ: 0 ANSI: 5
[ 12.522565] sd 1:0:0:0: [sda] 17803297 512-byte logical blocks: (9.11 GB/8.48 GiB)
[ 12.527093] sd 1:0:0:0: [sda] Write Protect is off
[ 12.530203] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 12.530363] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.534386] sda: sda1 sda2 sda3
[ 12.549122] sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
[ 12.552399] Uniform CD-ROM driver Revision: 3.20
[ 12.559095] sd 1:0:0:0: [sda] Attached SCSI disk
[ 12.574490] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 12.657115] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 12.660928] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 13.116435] device-mapper: uevent: version 1.0.3
[ 13.122993] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 14.009081] kjournald starting. Commit interval 5 seconds
[ 14.012839] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.688731] udev[183]: starting version 164
[ 20.997137] EXT3 FS on dm-0, internal journal
[ 21.652754] loop: module loaded
[ 23.530679] Adding 520176k swap on /dev/mapper/vg0-swap_1. Priority:-1 extents:1 across:520176k
[ 117.312988] kjournald starting. Commit interval 5 seconds
[ 117.317306] EXT3 FS on sda1, internal journal
[ 117.321183] EXT3-fs: mounted filesystem with ordered data mode.
[ 117.368485] kjournald starting. Commit interval 5 seconds
[ 117.372860] EXT3 FS on dm-5, internal journal
[ 117.376686] EXT3-fs: mounted filesystem with ordered data mode.
[ 117.410302] kjournald starting. Commit interval 5 seconds
[ 117.414500] EXT3 FS on dm-4, internal journal
[ 117.418244] EXT3-fs: mounted filesystem with ordered data mode.
[ 117.455781] kjournald starting. Commit interval 5 seconds
[ 117.460051] EXT3 FS on dm-2, internal journal
[ 117.463801] EXT3-fs: mounted filesystem with ordered data mode.
[ 117.506945] kjournald starting. Commit interval 5 seconds
[ 117.511260] EXT3 FS on dm-3, internal journal
[ 117.514995] EXT3-fs: mounted filesystem with ordered data mode.
[ 124.532199] eth0: Link is up using internal transceiver at 10Mb/s, Half Duplex.
[ 125.699049] fuse init (API version 7.13)
[ 131.687256] end_request: I/O error, dev fd0, sector 0
[ 136.330916] sr 2:0:0:0: [sr0] Unhandled sense code
[ 136.334866] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 136.338862] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[ 136.342901] Info fld=0xe416
[ 136.346861] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[ 136.350872] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 e4 14 00 00 04 00
[ 136.355009] end_request: I/O error, dev sr0, sector 233552
[ 136.359090] Buffer I/O error on device sr0, logical block 14597
[ 141.025344] sr 2:0:0:0: [sr0] Unhandled sense code
[ 141.029174] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 141.033260] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[ 141.037108] Info fld=0xe416
[ 141.040887] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[ 141.044756] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 e4 14 00 00 04 00
[ 141.048756] end_request: I/O error, dev sr0, sector 233552
[ 141.052592] Buffer I/O error on device sr0, logical block 14597
[ 146.772794] sr 2:0:0:0: [sr0] Unhandled sense code
[ 146.776808] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 146.780760] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[ 146.784616] Info fld=0xe416
[ 146.788405] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[ 146.792236] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 e4 14 00 00 04 00
[ 146.796220] end_request: I/O error, dev sr0, sector 233552
[ 146.799975] Buffer I/O error on device sr0, logical block 14597
[ 151.487568] sr 2:0:0:0: [sr0] Unhandled sense code
[ 151.491418] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 151.495266] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[ 151.499053] Info fld=0xe416
[ 151.502783] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[ 151.506581] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 e4 14 00 00 04 00
[ 151.510533] end_request: I/O error, dev sr0, sector 233552
[ 151.514335] Buffer I/O error on device sr0, logical block 14597
[ 156.222742] sr 2:0:0:0: [sr0] Unhandled sense code
[ 156.226554] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 156.230503] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[ 156.234448] Info fld=0xe416
[ 156.238336] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[ 156.242255] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 e4 14 00 00 04 00
[ 156.246394] end_request: I/O error, dev sr0, sector 233552
[ 156.250417] Buffer I/O error on device sr0, logical block 14597
[ 163.088915] vgaarb: this pci device is not a vga device
[ 163.209017] vgaarb: this pci device is not a vga device
[ 163.753373] tun: Universal TUN/TAP device driver, 1.6
[ 163.753397] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 164.347584] teredo: Disabled Privacy Extensions
[ 170.027080] ioctl32(powertweakd:1618): Unknown cmd fd(4) cmd(4010126a){t:12;sz:16} arg(ffaa9a10) on /dev/sda
[ 293.322504] tun: Disabled Privacy Extensions
[ 298.622018] teredo: no IPv6 routers present
[ 353.405479] vgaarb: this pci device is not a vga device
[ 353.418296] vgaarb: this pci device is not a vga device
[ 957.340240] vgaarb: this pci device is not a vga device
** Model information
cpu : TI UltraSparc IIi (Sabre)
fpu : UltraSparc IIi integrated FPU
pmu : ultra12
prom : OBP 3.19.4 1999/04/28 15:05
type : sun4u
** Loaded modules:
Module Size Used by
tun 11640 4
binfmt_misc 6807 1
fuse 48986 1
openpromfs 4455 0
loop 11079 0
evdev 7935 3
ext3 124832 6
jbd 34176 1 ext3
mbcache 5131 1 ext3
dm_mod 55620 21
sg 20523 0
sr_mod 13978 0
sd_mod 31604 3
cdrom 33647 1 sr_mod
crc_t10dif 1292 1 sd_mod
ata_generic 3199 0
pata_cmd64x 5390 2
sym53c8xx 71569 0
libata 147511 2 ata_generic,pata_cmd64x
scsi_transport_spi 20729 1 sym53c8xx
sunhme 25036 0
ide_pci_generic 2964 0
scsi_mod 132189 6 sg,sr_mod,sd_mod,sym53c8xx,libata,scsi_transport_spi
** PCI devices:
00:01.0 PCI bridge [0604]: Oracle Corporation Simba Advanced PCI Bridge [108e:5000] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Region 0: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 1: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Bus: primary=00, secondary=02, subordinate=ff, sec-latency=64
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[virtual] Expansion ROM at fffffe0100000000 [disabled] [size=1]
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:01.1 PCI bridge [0604]: Oracle Corporation Simba Advanced PCI Bridge [108e:5000] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Region 0: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 1: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[virtual] Expansion ROM at fffffe0100000000 [disabled] [size=1]
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:01.0 Bridge [0680]: Oracle Corporation EBUS [108e:1000] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (2500ns min, 6250ns max)
Region 0: Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 1: Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffffe0100000000 [disabled] [size=1]
01:01.1 Ethernet controller [0200]: Oracle Corporation Happy Meal 10/100 Ethernet [hme] [108e:1001] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (2500ns min, 1250ns max)
Interrupt: pin ? routed to IRQ 12
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=28K]
Region 1: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffffe0100000000 [disabled] [size=1]
Kernel driver in use: hme
01:02.0 VGA compatible controller [0300]: ATI Technologies Inc 3D Rage Pro 215GP [1002:4750] (rev 5c) (prog-if 00 [VGA controller])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 13
Region 0: Memory at e1000000 (32-bit, non-prefetchable) [disabled] [size=16M]
Region 1: I/O ports at fffffe0100000000 [disabled] [size=1]
Region 2: Memory at e2000000 (32-bit, non-prefetchable) [disabled] [size=4K]
Region 3: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffffe0100000000 [disabled] [size=1]
01:03.0 IDE interface [0101]: Silicon Image, Inc. PCI0646 [1095:0646] (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Silicon Image, Inc. PCI0646 [1095:0646]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at c00000 [size=8]
Region 1: I/O ports at c00008 [size=4]
Region 2: I/O ports at c00010 [size=8]
Region 3: I/O ports at c00018 [size=4]
Region 4: I/O ports at c00020 [size=16]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
[virtual] Expansion ROM at fffffe0100000000 [disabled] [size=1]
Kernel driver in use: pata_cmd64x
02:01.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c875 [1000:000f] (rev 14)
Subsystem: LSI Logic / Symbios Logic LSI53C876/E PCI to Dual Channel SCSI Controller [1000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (4250ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 0400 [size=256]
Region 1: Memory at 00002000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at 00004000 (32-bit, non-prefetchable) [size=4K]
Region 3: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffffe0100000000 [disabled] [size=1]
Kernel driver in use: sym53c8xx
02:01.1 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c875 [1000:000f] (rev 14)
Subsystem: LSI Logic / Symbios Logic LSI53C876/E PCI to Dual Channel SCSI Controller [1000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (4250ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 16
Region 0: I/O ports at 0800 [size=256]
Region 1: Memory at 00006000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at 00008000 (32-bit, non-prefetchable) [size=4K]
Region 3: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffffe0100000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffffe0100000000 [disabled] [size=1]
Kernel driver in use: sym53c8xx
** Sound cards:
-- System Information:
Debian Release: 6.0
Architecture: sparc (sparc64)
Kernel: Linux 2.6.32-5-sparc64
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-5-sparc64 depends on:
ii debconf [debconf 1.5.38 Debian configuration management sy
ii initramfs-tools 0.98.7 tools for generating an initramfs
ii linux-base 2.6.37-1~experimental.1 Linux image base package
ii module-init-tool 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-sparc64 recommends:
ii firmware-linux-free 2.6.32-30 Binary firmware for various driver
Versions of packages linux-image-2.6.32-5-sparc64 suggests:
ii fdutils 5.5-20060227-4 Linux floppy utilities
pn linux-doc-2.6.32 <none> (no description available)
ii silo 1.4.14+git20100228-1+b1 Sparc Improved LOader
Versions of packages linux-image-2.6.32-5-sparc64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-5-sparc64/postinst/missing-firmware-2.6.32-5-sparc64:
linux-image-2.6.32-5-sparc64/postinst/depmod-error-initrd-2.6.32-5-sparc64: false
linux-image-2.6.32-5-sparc64/postinst/ignoring-do-bootloader-2.6.32-5-sparc64:
linux-image-2.6.32-5-sparc64/prerm/removing-running-kernel-2.6.32-5-sparc64: true
linux-image-2.6.32-5-sparc64/prerm/would-invalidate-boot-loader-2.6.32-5-sparc64: true
linux-image-2.6.32-5-sparc64/postinst/bootloader-error-2.6.32-5-sparc64:
linux-image-2.6.32-5-sparc64/postinst/bootloader-test-error-2.6.32-5-sparc64:
--- End Message ---