Bug#806763: linux-image-4.2.0-0.bpo.1-amd64: aoe + bridged interfaces: aoe module prevents bridge from being taken down on shutdown or reboot with unregister_netdevice error
Package: src:linux
Version: 4.2.5-1~bpo8+1
Severity: important
Dear Maintainer,
* What led up to the situation?
On shutdown or reboot, an endless loop would be entered, with these lines being printed on occasion:
unregister_netdevice: waiting for lan0 to become free. Usage count = 6
where 'lan0' is a bridge device created via brctl
* What exactly did you do (or not do) that was effective (or
ineffective)?
I discovered that this only occurred when the lan0 bridge was taken down, and that I could repeat it w/o shutting down by using 'ifdown -a' or 'ifdown lan0'. Furthermore, I found that I had the 'aoe' module loaded but not used (lvm discovered AoE devices exported from another system that had LVM PVs on them, but no VGs on these devices were active on this system).
* What was the outcome of this action?
While the aoe kernel module was loaded, a system shutdown or reboot would be blocked while the system would attempt to bring the primary network interface down repeatedly in an endless loop. rmmoding the aoe module resolved the loop.
* What outcome did you expect instead?
A clean shutdown, with no requirement to rmmod the aoe module manually beforehand.
-- Package-specific info:
** Version:
Linux version 4.2.0-0.bpo.1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Debian 4.2.5-1~bpo8+1 (2015-11-02)
** Command line:
placeholder root=/dev/mapper/rohan-jessie--root ro iommu=soft
** Not tainted
** Kernel log:
[31025.250909] IPv6: ADDRCONF(NETDEV_UP): ExtVM1: link is not ready
[31025.259333] device eth0.7 entered promiscuous mode
[31025.267270] ExtVM1: port 1(eth0.7) entered forwarding state
[31025.267756] ExtVM1: port 1(eth0.7) entered forwarding state
[31025.680193] IPv6: ADDRCONF(NETDEV_UP): ExtVM2: link is not ready
[31025.692860] device eth0.8 entered promiscuous mode
[31025.700817] ExtVM2: port 1(eth0.8) entered forwarding state
[31025.701362] ExtVM2: port 1(eth0.8) entered forwarding state
[31026.113131] IPv6: ADDRCONF(NETDEV_UP): GuestNet: link is not ready
[31026.124270] device eth0.3 entered promiscuous mode
[31026.132267] GuestNet: port 1(eth0.3) entered forwarding state
[31026.132971] GuestNet: port 1(eth0.3) entered forwarding state
[31036.763554] GuestNet: port 1(eth0.3) entered disabled state
[31036.773369] device eth0.3 left promiscuous mode
[31036.775019] GuestNet: port 1(eth0.3) entered disabled state
[31036.908510] ExtVM2: port 1(eth0.8) entered disabled state
[31036.917998] device eth0.8 left promiscuous mode
[31036.919623] ExtVM2: port 1(eth0.8) entered disabled state
[31037.056552] ExtVM1: port 1(eth0.7) entered disabled state
[31037.065950] device eth0.7 left promiscuous mode
[31037.067529] ExtVM1: port 1(eth0.7) entered disabled state
[31037.205368] device eth0.6 left promiscuous mode
[31037.301798] lan0: port 1(eth0.2) entered disabled state
[31037.339777] device eth0.2 left promiscuous mode
[31037.341268] lan0: port 1(eth0.2) entered disabled state
[31037.640426] NoNet: port 1(eth0.5) entered disabled state
[31037.641744] device eth0.5 left promiscuous mode
[31037.642919] NoNet: port 1(eth0.5) entered disabled state
[31037.719875] device eth0 left promiscuous mode
[31037.721350] HomeDev: port 1(eth0.4) entered disabled state
[31037.722624] device eth0.4 left promiscuous mode
[31037.723799] HomeDev: port 1(eth0.4) entered disabled state
[31037.997187] NetworkManager[4029]: segfault at 38 ip 000000000042d68a sp 00007ffeef723508 error 4 in NetworkManager[400000+108000]
[31072.574843] e1000e: eth0 NIC Link is Down
[31098.153618] 8021q: adding VLAN 0 to HW filter on device eth0
[31098.162177] device eth0.7 entered promiscuous mode
[31098.167360] device eth0 entered promiscuous mode
[31098.176116] IPv6: ADDRCONF(NETDEV_UP): ExtVM1: link is not ready
[31100.506837] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[31100.508365] ExtVM1: port 1(eth0.7) entered forwarding state
[31100.509497] ExtVM1: port 1(eth0.7) entered forwarding state
[31100.510670] IPv6: ADDRCONF(NETDEV_CHANGE): ExtVM1: link becomes ready
[31100.718299] device eth0.8 entered promiscuous mode
[31100.727888] ExtVM2: port 1(eth0.8) entered forwarding state
[31100.729158] ExtVM2: port 1(eth0.8) entered forwarding state
[31101.137569] device eth0.3 entered promiscuous mode
[31101.147268] GuestNet: port 1(eth0.3) entered forwarding state
[31101.148503] GuestNet: port 1(eth0.3) entered forwarding state
[31101.559650] device eth0.4 entered promiscuous mode
[31101.568972] HomeDev: port 1(eth0.4) entered forwarding state
[31101.570231] HomeDev: port 1(eth0.4) entered forwarding state
[31101.980166] device eth0.5 entered promiscuous mode
[31101.989648] NoNet: port 1(eth0.5) entered forwarding state
[31101.990954] NoNet: port 1(eth0.5) entered forwarding state
[31102.400033] device eth0.6 entered promiscuous mode
[31103.969614] device eth0.2 entered promiscuous mode
[31103.977904] lan0: port 1(eth0.2) entered forwarding state
[31103.979157] lan0: port 1(eth0.2) entered forwarding state
[31115.538283] ExtVM1: port 1(eth0.7) entered forwarding state
[31115.730283] ExtVM2: port 1(eth0.8) entered forwarding state
[31116.178385] GuestNet: port 1(eth0.3) entered forwarding state
[31116.626311] HomeDev: port 1(eth0.4) entered forwarding state
[31117.010338] NoNet: port 1(eth0.5) entered forwarding state
[31118.994367] lan0: port 1(eth0.2) entered forwarding state
[31176.751835] aoe: AoE v85 initialised.
[31176.755306] aoe: e10.0: setting 1024 byte data frames
[31176.757033] aoe: e8.0: setting 1024 byte data frames
[31176.758655] aoe: e7.10: setting 1024 byte data frames
[31176.760260] aoe: e12.0: setting 1024 byte data frames
[31176.761928] aoe: e7.0: setting 1024 byte data frames
[31176.763507] aoe: e10.1: setting 1024 byte data frames
[31176.765090] aoe: bc5ff4e57ce7 e10.0 v4014 has 31457280 sectors
[31176.766647] aoe: bc5ff4e57ce7 e8.0 v4014 has 16777216 sectors
[31176.768173] aoe: bc5ff4e57ce7 e7.10 v4014 has 62914560 sectors
[31176.769918] aoe: bc5ff4e57ce7 e12.0 v4014 has 83886080 sectors
[31176.771423] aoe: bc5ff4e57ce7 e7.0 v4014 has 62914560 sectors
[31176.772912] aoe: bc5ff4e57ce7 e10.1 v4014 has 8388608 sectors
[31176.774563] etherd/e7.10: p1
[31176.777412] etherd/e7.0: p1 p2
[31176.778851] etherd/e12.0: p1
[31176.780774] etherd/e10.0: p1 p2 < p5 >
[31176.783241] etherd/e8.0: p1 p2 < p5 >
[31176.787351] etherd/e10.1: p1 p2 < p5 >
[31184.537864] lan0: port 1(eth0.2) entered disabled state
[31184.575459] device eth0.2 left promiscuous mode
[31184.576672] lan0: port 1(eth0.2) entered disabled state
[31194.868585] unregister_netdevice: waiting for lan0 to become free. Usage count = 6
[31205.108904] unregister_netdevice: waiting for lan0 to become free. Usage count = 6
[31667.235707] device eth0.2 entered promiscuous mode
[31667.245685] lan0: port 1(eth0.2) entered forwarding state
[31667.247353] lan0: port 1(eth0.2) entered forwarding state
[31682.274780] lan0: port 1(eth0.2) entered forwarding state
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 0204
board_vendor: ASUSTeK Computer INC.
board_name: M3A78-T
board_version: Rev 1.xx
** Loaded modules:
cfg80211
rfkill
xen_gntdev
xen_evtchn
xenfs
xen_privcmd
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
grace
fscache
sunrpc
8021q
garp
mrp
bridge
stp
llc
amdkfd
radeon
snd_hda_codec_realtek
snd_hda_codec_generic
snd_hda_codec_hdmi
psmouse
snd_hda_intel
serio_raw
snd_hda_codec
evdev
snd_hda_core
snd_hwdep
snd_pcm
snd_timer
snd
edac_mce_amd
edac_core
ttm
soundcore
pcspkr
drm_kms_helper
drm
k10temp
sp5100_tco
i2c_algo_bit
i2c_piix4
8250_fintek
wmi
asus_atk0110
shpchp
button
processor
thermal_sys
fuse
autofs4
xfs
crc32c_generic
libcrc32c
dm_mod
raid1
md_mod
sg
sd_mod
ata_generic
ohci_pci
firewire_ohci
firewire_core
crc_itu_t
ahci
libahci
pata_atiixp
e1000e
ohci_hcd
ehci_pci
ptp
pps_core
ehci_hcd
libata
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] RS780 Host Bridge [1022:9600]
Subsystem: ASUSTeK Computer Inc. Device [1043:834d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 1) [1022:960b] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:09.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 4) [1022:9608] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at 9000 [size=8]
Region 3: I/O ports at 8000 [size=4]
Region 4: I/O ports at 7000 [size=16]
Region 5: Memory at fe7ff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe7fe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:12.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe7fd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe7ff000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe7fc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe7fb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe7fa800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 3a)
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ff00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: ASUSTeK Computer Inc. Device [1043:82fe]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe7f4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d]
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B+ ParErr+ DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:834e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe7f9000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV635 [Radeon HD 3650/3750/4570/4580] [1002:9598] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited / Sapphire Technology Device [174b:e410]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe8f0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at c000 [size=256]
Expansion ROM at fe8c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] RV635 HDMI Audio [Radeon HD 3600 Series] [1002:aa20]
Subsystem: PC Partner Limited / Sapphire Technology Device [174b:aa20]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 62
Region 0: Memory at fe8ec000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
02:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV610 [Radeon HD 2400 PRO/XT] [1002:94c1] (prog-if 00 [VGA controller])
Subsystem: Dell Optiplex 755 [1028:0d02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 64
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe9f0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at d000 [size=256]
Expansion ROM at fe9c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
03:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Gigabit CT Desktop Adapter [8086:a01f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feae0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fea00000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at e800 [size=32]
Region 3: Memory at feadc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at fea80000 [disabled] [size=256K]
Capabilities: <access denied>
Kernel driver in use: e1000e
04:06.0 USB controller [0c03]: NEC Corporation OHCI USB Controller [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: Packard Bell B.V. Device [1631:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
04:06.1 USB controller [0c03]: NEC Corporation OHCI USB Controller [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: Packard Bell B.V. Device [1631:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
04:06.2 USB controller [0c03]: NEC Corporation uPD72010x USB 2.0 Controller [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: Packard Bell B.V. Device [1631:1600]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 23
Region 0: Memory at febfdc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
04:08.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW322/323 [TrueFire] 1394a Controller [11c1:5811] (rev 70) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. LSI FW322/323 IEEE 1394a FireWire Controller [1043:8294]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
not available
-- System Information:
Debian Release: 8.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 4.2.0-0.bpo.1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.0.6-3
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22
pn linux-doc-4.2 <none>
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.43
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
ii xen-hypervisor-4.4-amd64 [xen-hypervisor] 4.4.1-9+deb8u2
-- debconf information excluded
Reply to: