Bug#806304: linux-image-4.2.0-0.bpo.1-amd64: drm:gen8_irq_handler i915 *ERROR* The master control interrupt lied (SDE)!
Package: src:linux
Version: 4.2.6-1~bpo8+1
Severity: normal
Tags: upstream
Dear Maintainer,
After upgrading the kernel from 3.16 to version 4.2.0, the above error appears
in the kernel message buffer at start-up.
I have no HDMI, or VGA plugged, so in this circumstance the system seems to
work correctly.
For completeness I'm reporting also this:
francesco@debian-asus:~€ dmesg | grep -i drm
[ 0.564502] [drm] Initialized drm 1.1.0 20060810
[ 0.569177] [drm] Memory usable by graphics device = 4096M
[ 0.569180] [drm] Replacing VGA console driver
[ 0.577796] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.577798] [drm] Driver supports precise vblank timestamp query.
[ 0.597058] [drm:gen8_irq_handler [i915]] *ERROR* The master control
interrupt lied (SDE)!
[ 0.597227] [drm:gen8_irq_handler [i915]] *ERROR* The master control
interrupt lied (SDE)!
[ 0.597860] fbcon: inteldrmfb (fb0) is primary device
[ 0.598637] [drm] Initialized i915 1.6.0 20150522 for 0000:00:02.0 on minor
0
[ 1.728182] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
Could you be so kind to tell me something about it?!
Thanks for help,
Francesco
-- Package-specific info:
** Version:
Linux version 4.2.0-0.bpo.1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Debian 4.2.6-1~bpo8+1 (2015-11-18)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.2.0-0.bpo.1-amd64 root=UUID=28d11b58-7f20-4ed1-a0f0-14dc5581f989 ro initrd=/install/gtk/initrd.gz quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 7.784362] ath: phy0: WB335 2-ANT card detected
[ 7.784364] ath: phy0: Set BT/WLAN RX diversity capability
[ 7.793159] ath: phy0: Enable LNA combining
[ 7.794414] ath: phy0: ASPM enabled: 0x43
[ 7.794415] ath: EEPROM regdomain: 0x6a
[ 7.794415] ath: EEPROM indicates we should expect a direct regpair map
[ 7.794417] ath: Country alpha2 being used: 00
[ 7.794417] ath: Regpair used: 0x6a
[ 7.885712] iTCO_vendor_support: vendor-support=0
[ 7.886753] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 7.886786] iTCO_wdt: Found a Wildcat Point_LP TCO device (Version=2, TCOBASE=0x1860)
[ 7.886874] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.912518] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC3236: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 7.912520] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 7.912521] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 7.912522] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 7.912523] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 7.912524] snd_hda_codec_realtek hdaudioC1D0: Mic=0x1b
[ 7.918023] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 7.918086] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input16
[ 7.918150] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input17
[ 7.948000] AVX2 version of gcm_enc/dec engaged.
[ 7.948002] AES CTR mode by8 optimization enabled
[ 7.956172] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input18
[ 7.961400] psmouse serio4: elantech: assuming hardware version 4 (with firmware version 0x381f0a)
[ 7.965641] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 7.965816] ieee80211 phy0: Atheros AR9565 Rev:1 mem=0xffffc90001100000, irq=19
[ 7.975003] psmouse serio4: elantech: Synaptics capabilities query result 0x10, 0x14, 0x0e.
[ 7.989667] psmouse serio4: elantech: Elan sample query result 0b, 16, 75
[ 7.996443] asus_wmi: Initialization: 0x1
[ 7.996470] asus_wmi: BIOS WMI version: 7.9
[ 7.996496] asus_wmi: SFUN value: 0xa0077
[ 7.997116] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input19
[ 7.999761] asus_wmi: Number of fans: 1
[ 8.088406] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input14
[ 8.163469] sha256_ssse3: Using AVX2 optimized SHA-256 implementation
[ 8.720039] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[ 9.255031] media: Linux media interface: v0.10
[ 9.390173] Bluetooth: Core ver 2.20
[ 9.390186] NET: Registered protocol family 31
[ 9.390187] Bluetooth: HCI device and connection manager initialized
[ 9.390190] Bluetooth: HCI socket layer initialized
[ 9.390192] Bluetooth: L2CAP socket layer initialized
[ 9.390199] Bluetooth: SCO socket layer initialized
[ 9.569111] Linux video capture interface: v2.00
[ 10.033311] usbcore: registered new interface driver btusb
[ 10.038657] usb 1-7: USB disconnect, device number 3
[ 10.045606] intel_rapl: Found RAPL domain package
[ 10.045609] intel_rapl: Found RAPL domain core
[ 10.045611] intel_rapl: Found RAPL domain uncore
[ 10.045613] intel_rapl: Found RAPL domain dram
[ 10.176806] cfg80211: World regulatory domain updated:
[ 10.176808] cfg80211: DFS Master region: unset
[ 10.176809] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.176811] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.176813] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.176814] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.176815] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 10.176817] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.176818] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.176819] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.176820] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.199819] usbcore: registered new interface driver ath3k
[ 10.442646] uvcvideo: Found UVC 1.00 device USB Camera (0bda:57bc)
[ 10.448586] input: USB Camera as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input20
[ 10.448631] usbcore: registered new interface driver uvcvideo
[ 10.448633] USB Video Class driver (1.1.1)
[ 11.634519] Adding 4101116k swap on /dev/sda8. Priority:-1 extents:1 across:4101116k FS
[ 13.046020] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 13.666694] systemd-journald[187]: Received request to flush runtime journal from PID 1
[ 14.285171] RPC: Registered named UNIX socket transport module.
[ 14.285173] RPC: Registered udp transport module.
[ 14.285174] RPC: Registered tcp transport module.
[ 14.285175] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.333393] FS-Cache: Loaded
[ 14.377652] FS-Cache: Netfs 'nfs' registered for caching
[ 14.454391] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 15.531811] vboxdrv: Found 4 processor cores
[ 15.550313] vboxdrv: TSC mode is Invariant, tentative frequency 2396521069 Hz
[ 15.550316] vboxdrv: Successfully loaded version 5.0.10 (interface 0x00240000)
[ 16.309121] VBoxNetFlt: Successfully started.
[ 16.586850] VBoxNetAdp: Successfully started.
[ 16.887255] VBoxPciLinuxInit
[ 17.054581] vboxpci: IOMMU not found (not registered)
[ 20.632874] r8169 0000:02:00.1: firmware: direct-loading firmware rtl_nic/rtl8411-2.fw
[ 20.652813] r8169 0000:02:00.1 eth0: link down
[ 23.083413] bbswitch: version 0.8
[ 23.083418] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
[ 23.083422] bbswitch: Found discrete VGA device 0000:04:00.0: \_SB_.PCI0.RP05.PEGP
[ 23.083430] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150619/nsarguments-95)
[ 23.083499] bbswitch: detected an Optimus _DSM function
[ 23.083563] bbswitch: Succesfully loaded. Discrete card 0000:04:00.0 is on
[ 23.084932] bbswitch: disabling discrete graphics
[ 23.084942] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150619/nsarguments-95)
[ 78.699434] wlan0: authenticate with b8:a3:86:62:b1:96
[ 78.711773] wlan0: send auth to b8:a3:86:62:b1:96 (try 1/3)
[ 78.714165] wlan0: authenticated
[ 78.716062] wlan0: associate with b8:a3:86:62:b1:96 (try 1/3)
[ 78.720507] wlan0: RX AssocResp from b8:a3:86:62:b1:96 (capab=0x411 status=0 aid=6)
[ 78.720596] wlan0: associated
** Model information
sys_vendor: ASUSTeK COMPUTER INC.
product_name: X751LX
product_version: 1.0
chassis_vendor: ASUSTeK COMPUTER INC.
chassis_version: 1.0
bios_vendor: American Megatrends Inc.
bios_version: X751LX.403
board_vendor: ASUSTeK COMPUTER INC.
board_name: X751LX
board_version: 1.0
** Loaded modules:
ctr
ccm
bbswitch(O)
pci_stub
vboxpci(O)
vboxnetadp(O)
binfmt_misc
vboxnetflt(O)
vboxdrv(O)
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
grace
fscache
sunrpc
uvcvideo
x86_pkg_temp_thermal
intel_powerclamp
videobuf2_vmalloc
ath3k
videobuf2_memops
intel_rapl
btusb
videobuf2_core
btrtl
v4l2_common
coretemp
btbcm
btintel
videodev
kvm_intel
bluetooth
media
kvm
crct10dif_pclmul
crc32_pclmul
joydev
sha256_ssse3
sha256_generic
hmac
drbg
asus_nb_wmi
ansi_cprng
arc4
aesni_intel
aes_x86_64
snd_hda_codec_realtek
snd_hda_codec_hdmi
snd_hda_codec_generic
iTCO_wdt
iTCO_vendor_support
snd_soc_rt5640
ath9k
asus_wmi
lrw
gf128mul
sparse_keymap
glue_helper
ath9k_common
snd_soc_rl6231
snd_hda_intel
snd_hda_codec
snd_hda_core
snd_soc_core
ath9k_hw
snd_compress
regmap_i2c
ablk_helper
snd_hwdep
ath
snd_pcm
mac80211
cfg80211
snd_timer
cryptd
i2c_designware_platform
snd
psmouse
pcspkr
i2c_designware_core
rtsx_pci_ms
memstick
rfkill
serio_raw
ac
evdev
int3400_thermal
snd_soc_sst_acpi
dw_dmac
acpi_pad
battery
dw_dmac_core
acpi_thermal_rel
int3402_thermal
mei_me
soundcore
i2c_i801
shpchp
lpc_ich
mei
processor
processor_thermal_device
intel_soc_dts_iosf
int340x_thermal_zone
iosf_mbi
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
dm_mod
sg
sd_mod
sr_mod
cdrom
rtsx_pci_sdmmc
mxm_wmi
ahci
libahci
crc32c_intel
libata
scsi_mod
xhci_pci
r8169
mii
xhci_hcd
rtsx_pci
mfd_core
usbcore
usb_common
i915
i2c_algo_bit
drm_kms_helper
drm
fan
thermal
wmi
sdhci_acpi
video
sdhci
thermal_sys
mmc_core
i2c_hid
hid
button
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Broadwell-U Host Bridge -OPI [8086:1604] (rev 09)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: bdw_uncore
00:02.0 VGA compatible controller [0300]: Intel Corporation Broadwell-U Integrated Graphics [8086:1616] (rev 09) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 48
Region 0: Memory at f5000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:03.0 Audio device [0403]: Intel Corporation Broadwell-U Audio Controller [8086:160c] (rev 09)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at f731c000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:04.0 Signal processing controller [1180]: Intel Corporation Broadwell-U Camarillo Device [8086:1603] (rev 09)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7310000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: proc_thermal
00:14.0 USB controller [0c03]: Intel Corporation Wildcat Point-LP USB xHCI Controller [8086:9cb1] (rev 03) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:201f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at f7300000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation Wildcat Point-LP MEI Controller #1 [8086:9cba] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 51
Region 0: Memory at f7324000 (64-bit, non-prefetchable) [size=32]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:1b.0 Audio device [0403]: Intel Corporation Wildcat Point-LP High Definition Audio Controller [8086:9ca0] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:146f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 52
Region 0: Memory at f7318000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root Port #1 [8086:9c90] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root Port #3 [8086:9c94] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7200000-f72fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root Port #4 [8086:9c96] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f7100000-f71fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root Port #5 [8086:9c98] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f6000000-f70fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge [0601]: Intel Corporation Wildcat Point-LP LPC Controller [8086:9cc3] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation Wildcat Point-LP SATA Controller [AHCI Mode] [8086:9c83] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 50
Region 0: I/O ports at f0b0 [size=8]
Region 1: I/O ports at f0a0 [size=4]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7322000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation Wildcat Point-LP SMBus Controller [8086:9ca2] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7321000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
00:1f.6 Signal processing controller [1180]: Intel Corporation Wildcat Point-LP Thermal Management Controller [8086:9ca4] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:241a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 3
Region 0: Memory at f7320000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device [10ec:5287] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:202f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 46
Region 0: Memory at f7215000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at f7200000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: rtsx_pci
02:00.1 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 12)
Subsystem: ASUSTeK Computer Inc. Device [1043:200f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at f7214000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at f7210000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
03:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01)
Subsystem: AzureWave Device [1a3b:2130]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f7100000 (64-bit, non-prefetchable) [size=512K]
Expansion ROM at f7180000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
04:00.0 3D controller [0302]: NVIDIA Corporation Device [10de:139a] (rev ff) (prog-if ff)
!!! Unknown header type 7f
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 0bda:57bc Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 8.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.2.0-0.bpo.1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 4.0~bpo8+1
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.0.6-3
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22
pn linux-doc-4.2 <none>
Versions of packages linux-image-4.2.0-0.bpo.1-amd64 is related to:
ii firmware-atheros 0.44~bpo8+1
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.44~bpo8+1
pn xen-hypervisor <none>
-- debconf information:
linux-image-4.2.0-0.bpo.1-amd64/postinst/mips-initrd-4.2.0-0.bpo.1-amd64:
linux-image-4.2.0-0.bpo.1-amd64/postinst/depmod-error-initrd-4.2.0-0.bpo.1-amd64: false
linux-image-4.2.0-0.bpo.1-amd64/prerm/removing-running-kernel-4.2.0-0.bpo.1-amd64: true
Reply to: