Bug#784146: linux-image-3.16.0-4-armmp-lpae: Spurious RTC error messages on OpenBlocks AX3-4
Package: src:linux
Version: 3.16.7-ckt9-3~deb8u1
Severity: normal
Tags: upstream
On the OpenBlocks AX3-4, the kernel logs these messages at every boot:
[ 1.853325] rtc-mv d0010300.rtc: internal RTC not ticking
[ 1.863449] /build/linux-vwVRbb/linux-3.16.7-ckt9/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
The internal RTC is not expected to work on this model so it should
be disabled in the Device Tree:
<http://thread.gmane.org/gmane.linux.kernel.stable/131173>. That
will fix the first error message.
The second message also seems inappropriate in cases where no RTC
device exists. Also the path prefix isn't helpful.
Ben.
-- Package-specific info:
** Version:
Linux version 3.16.0-4-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-3~deb8u1 (2015-04-24)
** Command line:
console=ttyS0,115200 earlyprintk quiet
** Not tainted
** Kernel log:
[ 1.977147] orion-ehci d0050000.usb: EHCI Host Controller
[ 1.977418] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1
[ 1.977508] orion-ehci d0050000.usb: irq 27, io mem 0xd0050000
[ 1.987979] SCSI subsystem initialized
[ 1.989285] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[ 1.989504] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.989514] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.989521] usb usb1: Product: EHCI Host Controller
[ 1.989528] usb usb1: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 1.989535] usb usb1: SerialNumber: d0050000.usb
[ 1.990075] hub 1-0:1.0: USB hub found
[ 1.990113] hub 1-0:1.0: 1 port detected
[ 1.990533] orion-ehci d0051000.usb: EHCI Host Controller
[ 1.990923] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 2
[ 1.991027] orion-ehci d0051000.usb: irq 28, io mem 0xd0051000
[ 1.993768] libata version 3.00 loaded.
[ 2.001274] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00
[ 2.001492] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.001501] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.001509] usb usb2: Product: EHCI Host Controller
[ 2.001516] usb usb2: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 2.001523] usb usb2: SerialNumber: d0051000.usb
[ 2.002440] hub 2-0:1.0: USB hub found
[ 2.002476] hub 2-0:1.0: 1 port detected
[ 2.003311] libphy: orion_mdio_bus: probed
[ 2.045330] mvneta d0034000.ethernet eth3: Using random mac address 6e:77:de:5e:56:d5
[ 2.047218] sata_mv d00a0000.sata: version 1.28
[ 2.047387] sata_mv d00a0000.sata: slots 32 ports 2
[ 2.051994] scsi0 : sata_mv
[ 2.055838] scsi1 : sata_mv
[ 2.056058] ata1: SATA max UDMA/133 irq 31
[ 2.056066] ata2: SATA max UDMA/133 irq 31
[ 2.301274] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.446502] usb 1-1: New USB device found, idVendor=050d, idProduct=0249
[ 2.446511] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 2.446519] usb 1-1: Product: Multimedia Reader & Writer
[ 2.446526] usb 1-1: Manufacturer: BELKIN
[ 2.446532] usb 1-1: SerialNumber: 07102900000A
[ 2.451395] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.451690] scsi2 : usb-storage 1-1:1.0
[ 2.451977] usbcore: registered new interface driver usb-storage
[ 2.529272] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[ 2.545293] ata1.00: ATA-7: ST910021AS, 8.04, max UDMA/133
[ 2.545303] ata1.00: 195371568 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.569294] ata1.00: configured for UDMA/133
[ 2.569605] scsi 0:0:0:0: Direct-Access ATA ST910021AS 8.04 PQ: 0 ANSI: 5
[ 2.889258] ata2: SATA link down (SStatus 0 SControl F300)
[ 2.894916] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[ 2.895125] sd 0:0:0:0: [sda] Write Protect is off
[ 2.895135] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.895225] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.994017] sda: sda1 sda2 < sda5 >
[ 2.995163] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.996460] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.306187] device-mapper: uevent: version 1.0.3
[ 3.306421] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 3.450704] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: 0
[ 3.605268] scsi 2:0:0:1: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: 0
[ 3.606170] scsi 2:0:0:2: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: 0
[ 3.607042] scsi 2:0:0:3: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: 0
[ 3.607923] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.608673] sd 2:0:0:1: Attached scsi generic sg2 type 0
[ 3.614439] sd 2:0:0:2: Attached scsi generic sg3 type 0
[ 3.615270] sd 2:0:0:3: Attached scsi generic sg4 type 0
[ 3.620657] sd 2:0:0:2: [sdd] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 3.621332] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 3.623770] sd 2:0:0:2: [sdd] Write Protect is off
[ 3.623781] sd 2:0:0:2: [sdd] Mode Sense: 03 00 00 00
[ 3.629400] sd 2:0:0:2: [sdd] No Caching mode page found
[ 3.634763] sd 2:0:0:2: [sdd] Assuming drive cache: write through
[ 3.638275] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 3.640951] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 3.669339] sdd: sdd1
[ 3.682358] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 3.694403] PM: Starting manual resume from disk
[ 3.694420] PM: Hibernation image partition 254:1 present
[ 3.694425] PM: Looking for hibernation image.
[ 3.694722] PM: Image not found (code -22)
[ 3.694742] PM: Hibernation image not present or could not be loaded.
[ 4.101194] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 4.773812] random: nonblocking pool is initialized
[ 4.910503] systemd[1]: /etc/mtab is not a symlink or not pointing to /proc/self/mounts. This is not supported anymore. Please make sure to replace this file by a symlink to avoid incorrect or misleading mount(8) output.
[ 5.507885] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 6.016325] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 6.302002] systemd-udevd[189]: starting version 215
[ 6.936210] orion_wdt: Initial timeout 171 sec
[ 8.146488] Adding 4009980k swap on /dev/mapper/marmaduke--vg-swap_1. Priority:-1 extents:1 across:4009980k FS
[ 8.665821] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 8.675043] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 8.839530] systemd-journald[185]: Received request to flush runtime journal from PID 1
[ 9.273565] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.036516] RPC: Registered named UNIX socket transport module.
[ 10.036529] RPC: Registered udp transport module.
[ 10.036535] RPC: Registered tcp transport module.
[ 10.036540] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.074948] FS-Cache: Loaded
[ 10.110490] FS-Cache: Netfs 'nfs' registered for caching
[ 10.163280] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.273747] mvneta d0070000.ethernet eth0: link up
[ 13.273772] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
Hardware : Marvell Armada 370/XP (Device Tree)
Revision : 0000
** Loaded modules:
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
orion_wdt
evdev
leds_gpio
i2c_mv64xxx
autofs4
ext4
crc16
mbcache
jbd2
dm_mod
sg
sd_mod
crc_t10dif
crct10dif_generic
crct10dif_common
usb_storage
sata_mv
libata
scsi_mod
mvmdio
ehci_orion
ehci_hcd
mvneta
** PCI devices:
00:01.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:7846] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
** USB devices:
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 050d:0249 Belkin Components USB 2 Flash Media Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 8.0
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: armhf (armv7l)
Kernel: Linux 3.16.0-4-armmp-lpae (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-armmp-lpae depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-4-armmp-lpae recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-3.16.0-4-armmp-lpae suggests:
pn debian-kernel-handbook <none>
pn fdutils <none>
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-armmp-lpae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-armmp-lpae/postinst/depmod-error-initrd-3.16.0-4-armmp-lpae: false
linux-image-3.16.0-4-armmp-lpae/prerm/removing-running-kernel-3.16.0-4-armmp-lpae: true
linux-image-3.16.0-4-armmp-lpae/postinst/mips-initrd-3.16.0-4-armmp-lpae:
Reply to: