Bug#783881: Jessie: hanging on shutdown after turning off display and disks
Package: src:linux
Version: 3.16.7-ckt9-3~deb8u1
Severity: important
If I do a shutdown from MATE, my system does the following:
* MATE closes as expected
* within a couple of seconds the display switches off (all OK so far)
* then very shortly after that I hear at least some of my disks spinning down (as I'd expect)
* However my CPU and power fans continue to spin, and my power LED remains on.
I would expect the system to power off at this point.
To power off, I have to press and hold the power button for a few seconds.
I can't see any kernel messages at this point because by this stage the graphics
card has switched off.
I can reboot normally, and I can also press the RESET button and boot fine
once the shutdown process has hung in the described not-quite-off state.
This problem is intermittent, but seems much more likely to occur
if shutting down after a cold boot than it is if shutting down having
rebooted the machine.
Have previously had this enabled in /etc/hdparm.conf, around the time I started to notice this issue:
/dev/disk/by-id/ata-WDC_WD30EZRX-00SPEB0_WD-WCC4EHHH3TH7 {
spindown_time = 240
}
/dev/disk/by-id/ata-WDC_WD30EZRX-00SPEB0_WD-WCC4ENVNFAV0 {
spindown_time = 240
}
/dev/disk/by-id/ata-WDC_WD20EARX-00ZUDB0_WD-WCC1H0246293 {
spindown_time = 240
}
I've now commented them out but it's still giving me problems, so
I doubt those spindown_times have caused the problem but thought I'd
mention it in case anyone disagrees (I'm unsure if they continue to take
effect across cold boots).
This is Debian Jessie, installed from scratch.
-- Package-specific info:
** Version:
Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-3~deb8u1 (2015-04-24)
** Command line:
BOOT_IMAGE=/vmlinuz-3.16.0-4-amd64 root=/dev/mapper/oak-debian ro
** Not tainted
** Kernel log:
[ 8.363510] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.363565] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000053f (\GPS0) (20140424/utaddress-258)
[ 8.363693] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.363748] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 8.418058] ACPI Warning: SystemIO range 0x0000000000000400-0x000000000000041f conflicts with OpRegion 0x0000000000000400-0x000000000000040f (\SMRG) (20140424/utaddress-258)
[ 8.418188] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.533746] input: PC Speaker as /devices/platform/pcspkr/input/input10
[ 8.673093] sound hdaudioC0D0: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 8.673151] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.673196] sound hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 8.673240] sound hdaudioC0D0: mono: mono_out=0x0
[ 8.673283] sound hdaudioC0D0: dig-out=0x11/0x1e
[ 8.673326] sound hdaudioC0D0: inputs:
[ 8.673369] sound hdaudioC0D0: Front Mic=0x19
[ 8.673412] sound hdaudioC0D0: Rear Mic=0x18
[ 8.673454] sound hdaudioC0D0: Line=0x1a
[ 8.685084] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input11
[ 8.685307] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 8.685392] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 8.685476] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 8.685560] input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[ 8.685645] input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[ 8.685730] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[ 8.685815] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
[ 8.685900] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input19
[ 8.874793] [drm] Initialized drm 1.1.0 20060810
[ 8.943573] wmi: Mapper loaded
[ 9.060348] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x298200a2
[ 9.060396] nouveau [ DEVICE][0000:01:00.0] Chipset: G98 (NV98)
[ 9.060440] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 9.060505] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 9.104555] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 9.104599] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 9.104732] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 9.104777] nouveau [ VBIOS][0000:01:00.0] version 62.98.29.00.00
[ 9.124978] nouveau 0000:01:00.0: irq 45 for MSI/MSI-X
[ 9.124987] nouveau [ PMC][0000:01:00.0] MSI interrupts enabled
[ 9.125058] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 9.125108] nouveau [ PFB][0000:01:00.0] RAM size: 512 MiB
[ 9.125158] nouveau [ PFB][0000:01:00.0] ZCOMP: 960 tags
[ 9.278717] iTCO_vendor_support: vendor-support=0
[ 9.334402] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 9.334564] iTCO_wdt: Found a ICH10 TCO device (Version=2, TCOBASE=0x0860)
[ 9.334915] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.404024] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
[ 10.404084] nouveau [ PTHERM][0000:01:00.0] fan management: automatic
[ 10.404136] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 10.404203] nouveau [ CLK][0000:01:00.0] 0f: core 567 MHz shader 1350 MHz memory 400 MHz
[ 10.404297] nouveau [ CLK][0000:01:00.0] --: core 566 MHz shader 1350 MHz memory 399 MHz
[ 10.404475] [TTM] Zone kernel: Available graphics memory: 3063378 kiB
[ 10.404526] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 10.404576] [TTM] Initializing pool allocator
[ 10.404629] [TTM] Initializing DMA pool allocator
[ 10.404687] nouveau [ DRM] VRAM: 512 MiB
[ 10.404736] nouveau [ DRM] GART: 1048576 MiB
[ 10.404788] nouveau [ DRM] TMDS table version 2.0
[ 10.404838] nouveau [ DRM] DCB version 4.0
[ 10.404887] nouveau [ DRM] DCB outp 00: 02000300 00000028
[ 10.404938] nouveau [ DRM] DCB outp 01: 01000302 00000030
[ 10.404988] nouveau [ DRM] DCB outp 02: 04011310 00000028
[ 10.405038] nouveau [ DRM] DCB conn 00: 00001030
[ 10.405123] nouveau [ DRM] DCB conn 01: 00000100
[ 10.412228] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 10.412279] [drm] Driver supports precise vblank timestamp query.
[ 10.421960] nouveau [ DRM] MM: using M2MF for buffer copies
[ 10.431121] BTRFS info (device sdb): disk space caching is enabled
[ 10.486906] nouveau [ DRM] allocated 1680x1050 fb: 0x70000, bo ffff8801a86d7800
[ 10.487035] fbcon: nouveaufb (fb0) is primary device
[ 10.487115] BTRFS: bdev /dev/sdb errs: wr 64, rd 69, flush 0, corrupt 0, gen 0
[ 10.556308] Console: switching to colour frame buffer device 210x65
[ 10.558238] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 10.558240] nouveau 0000:01:00.0: registered panic notifier
[ 10.568020] [drm] Initialized nouveau 1.1.2 20120801 for 0000:01:00.0 on minor 0
[ 11.076023] floppy0: no floppy controllers found
[ 11.718989] Adding 41943036k swap on /dev/sda5. Priority:-1 extents:1 across:41943036k FS
[ 12.140932] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 12.305124] systemd-journald[188]: Received request to flush runtime journal from PID 1
[ 13.221410] RPC: Registered named UNIX socket transport module.
[ 13.221703] RPC: Registered udp transport module.
[ 13.221968] RPC: Registered tcp transport module.
[ 13.222478] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.235469] FS-Cache: Loaded
[ 13.254559] FS-Cache: Netfs 'nfs' registered for caching
[ 13.292641] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 15.525096] cfg80211: Calling CRDA to update world regulatory domain
[ 15.648592] cfg80211: World regulatory domain updated:
[ 15.648808] cfg80211: DFS Master region: unset
[ 15.648812] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 15.649358] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.649776] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.650193] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.650610] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 15.651029] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 15.651443] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 15.651855] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.652276] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 16.315799] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.316068] ATL1E 0000:02:00.0 eth0: NIC Link is Up <1000 Mbps Full Duplex>
[ 16.316285] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1609.069778] perf interrupt took too long (2503 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
** Model information
sys_vendor: System manufacturer
product_name: P5QL PRO
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 1004
board_vendor: ASUSTeK Computer INC.
board_name: P5QL PRO
board_version: Rev 1.xx
** Loaded modules:
cfg80211
rfkill
cpufreq_powersave
cpufreq_conservative
cpufreq_userspace
cpufreq_stats
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
iTCO_wdt
iTCO_vendor_support
coretemp
kvm_intel
kvm
joydev
nouveau
evdev
mxm_wmi
wmi
video
ttm
drm_kms_helper
drm
i2c_algo_bit
snd_hda_codec_realtek
snd_hda_codec_generic
pcspkr
psmouse
serio_raw
i2c_i801
i2c_core
lpc_ich
snd_hda_intel
mfd_core
snd_hda_controller
snd_hda_codec
snd_hwdep
snd_pcm
snd_timer
snd
soundcore
button
asus_atk0110
shpchp
acpi_cpufreq
processor
thermal_sys
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
btrfs
xor
raid6_pq
dm_mod
sg
sd_mod
crc_t10dif
crct10dif_generic
sr_mod
cdrom
crct10dif_common
hid_microsoft
hid_generic
usbhid
hid
ahci
libahci
libata
scsi_mod
ehci_pci
uhci_hcd
ehci_hcd
atl1e
usbcore
usb_common
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:24:8c:2a:5c:52 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.4/24 brd 192.168.1.255 scope global dynamic eth0
valid_lft 206370sec preferred_lft 206370sec
inet6 fe80::224:8cff:fe2a:5c52/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
eth0: 9283083 8533 0 0 0 0 0 2 764721 6877 0 0 0 0 1 0
lo: 4325 37 0 0 0 0 0 0 4325 37 0 0 0 0 0 0
*** Protocol statistics:
Ip:
8237 total packets received
1 with invalid addresses
0 forwarded
0 incoming packets discarded
8236 incoming packets delivered
6602 requests sent out
32 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
117 active connections openings
2 passive connection openings
4 failed connection attempts
2 connection resets received
2 connections established
7604 segments received
6021 segments send out
12 segments retransmited
2 bad segments received.
22 resets sent
Udp:
657 packets received
0 packets to unknown port received.
0 packet receive errors
656 packets sent
UdpLite:
TcpExt:
37 TCP sockets finished time wait in fast timer
120 delayed acks sent
Quick ack mode was activated 2 times
1646 packets directly queued to recvmsg prequeue.
2309768 bytes directly received in process context from prequeue
4707 packet headers predicted
1642 packets header predicted and directly queued to user
383 acknowledgments not containing data payload received
519 predicted acknowledgments
1 congestion windows recovered without slow start after partial ack
1 other TCP timeouts
TCPLossProbes: 11
TCPLossProbeRecovery: 10
2 DSACKs sent for old packets
6 connections reset due to unexpected data
2 connections reset due to early user close
TCPRcvCoalesce: 263
TCPOFOQueue: 247
TCPChallengeACK: 2
TCPSYNChallenge: 2
TCPAutoCorking: 49
TCPSynRetrans: 1
TCPOrigDataSent: 946
IpExt:
InMcastPkts: 33
OutMcastPkts: 33
InOctets: 9153750
OutOctets: 650603
InMcastOctets: 4891
OutMcastOctets: 4499
InNoECTPkts: 8237
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e20] (rev 03)
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 4 Series Chipset PCI Express Root Port [8086:2e21] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-feafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at c800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at cc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller [8086:3a3e]
Subsystem: ASUSTeK Computer Inc. Device [1043:82fe]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f9ff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0000000-f03fffff
Prefetchable memory behind bridge: 00000000f8f00000-00000000f8ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 [8086:3a4a] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000f0400000-00000000f05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at c080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at c400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at c480 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f9fff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIB (ICH10) LPC Interface Controller [8086:3a18]
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller [8086:3a22] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=32]
Region 5: Memory at f9ffe800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller [8086:3a30]
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9fff400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G98 [GeForce 8400 GS Rev. 2] [10de:06e4] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:8321]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at dc00 [size=128]
Expansion ROM at feae0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
02:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet [1969:1026] (rev b0)
Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard [1043:8304]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febc0000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ec00 [size=128]
Capabilities: <access denied>
Kernel driver in use: ATL1E
** USB devices:
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 003: ID 045e:00db Microsoft Corp. Natural Ergonomic Keyboard 4000 V1.0
Bus 008 Device 002: ID 046d:c00e Logitech, Inc. M-BJ58/M-BJ69 Optical Wheel Mouse
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 003: ID 05f3:0007 PI Engineering, Inc. Kinesis Advantage PRO MPC/USB Keyboard
Bus 007 Device 002: ID 05f3:0081 PI Engineering, Inc. Kinesis Integrated Hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.16.0-4-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-4-amd64 recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-3.16.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-amd64/prerm/removing-running-kernel-3.16.0-4-amd64: true
linux-image-3.16.0-4-amd64/postinst/depmod-error-initrd-3.16.0-4-amd64: false
linux-image-3.16.0-4-amd64/postinst/mips-initrd-3.16.0-4-amd64:
Reply to: